Search Documents

By R. V. Peche

Since 1952, Bond’s equation has been used as a standard to predict the specific energy of grinding for a given duty. The Bond’s equation considers that the exponent is constant for all conditions. Hukki, in 1961, pointed out that the exponent is a function of the particle size, and concluded that the Bond’s equation applies successfully for an intermediate range of sizes; out of this range the Bond’s equation leads to high error as demonstrated in this paper. More recently, in 2004, S. Morrell presented a new formula in which the exponents vary with the feed and product size. This paper is based on Hukki’s approach and presents a new general formula, in which the exponent varies only with the feed particle size. This new equation has been proven in 82 observable cases in Peru and other countries around the world, involving ball mills and vertimills in different configurations over a wide range of feed and product sizes, work indices and mill diameters; in most cases, the predicted value has an error less than 10% with regards to the observed value and no need for any correction factor. Keywords: Grinding, specific energy, particle size, work index, variable exponent

Jan 1, 2020

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By M. Getz, G. Asbjörnsson, M. Evertsson, E. Clausen

The mining and minerals processing industry is gradually being digitalised to improve efficiency and reduce waste. One aspect of this transition is to ensure that relevant process-data in sufficient quality and quantity is given to the operator in the right format and at the right time to improve decision-making. Augmented reality (AR) can serve as a potential ICT-based support tool for human operators to achieve this goal. With AR, virtual information is combined with the real world in real-time. Therefore, AR technology has the potential to fulfil the need for improved data visualisation in Industry 4.0. This article is the result of a collaborative effort of Chalmers University of Technology and RWTH Aachen University to identify selected state-of-the-art applications of AR that are currently being applied in the mining and minerals industry or selected related industries. This paper aims to show opportunities for the application of AR in the mining and mineral processing industry with selected conceptual applications. This paper concludes with several requirements identified as necessary to implement the conceptual applications of AR in the mining and minerals industry. Keywords: Augmented reality, mining, mineral processing

Jan 1, 2020

By J. E. Dickinson, R. Campbell, M. J. Cole, K. P. Galvin, M. C. Cole

It is common practice in the beneficiation of iron ore ultrafines to apply reverse flotation, and hence float the gangue minerals, leaving behind a high-grade iron ore product. Given the difficulty in floating particles finer than 20 μm, especially those finer than 10 μm, it is necessary to subject the feed to desliming ahead of flotation. There are two problems with this approach. Firstly, given the known inefficiencies of cyclones, desliming needs to be aggressively applied to particle sizes upwards of 45 μm to ensure all the offending ultrafine gangue is removed. Secondly, desliming also removes a significant portion of the valuable iron ore. Thus, a significant portion of the ultrafines, including the iron ore, is lost to the tailings. This paper examines the direct flotation of iron ore fines using the Reflux Flotation Cell. The RFC operates using a concentrated bubbly zone, in the absence of a conventional froth zone, for delivering strong counter current washing through an inverted fluidised bed of bubbles ahead of the product discharge. A system of parallel inclined channels in the lower part of the cell provides enhanced segregation of the bubbles from the tailings, preventing the loss of air bubbles into the tailings. Experiments conducted under semi-batch conditions produced encouraging results with concentrates of ~65% Fe grade in a single flotation stage. Comparatively, up to five successive batch flotation stages were required when using a laboratory scale batch mechanical flotation cell to achieve similar Fe grades. For a given grade, lower Fe recoveries were typically achieved by the RFC. This was attributed to the effective prevention of ultrafine particles succumbing to hydraulic entrainment under a positive bias flux, as well as an increasing feed volume involved in the semi-batch operation using inverted fluidisation water for cleaning. Overall, similar grade-recovery curves were produced, however, significantly higher grades were obtained by the RFC and with fewer separation stages. Keywords: Desliming flotation, iron ore, modified release analysis, reflux flotation cell

Jan 1, 2020

By A. Chagnes

This paper presents a modelling tool that can be used to predict the behaviour of solvent extraction processes. In particular, this model allows calculating metal extraction efficiency as a function of pH, solvent flowrate, stripping flowrate and aqueous feed flowrate in the mixers-settlers. This model is applied to the recovery of cobalt from acidic chloride media by using CYANEX® 272 as extractant diluted in kerosene. Keywords: Cobalt, mixer-settler, modelling, solvent extraction

Jan 1, 2020

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

By J. Ojeda, R. Kuyvenhoven, M. Ziemski M

This paper focusses on the identification of operational opportunities in a 1100 tph pellet plant to reduce the specific energy consumption in its comminution circuit, which is designed to process magnetite ore and produce pellets to be used as raw material in the iron and steel industry. The assessment is carried out through a frequency analysis for three of the four processing lines of the plant, consisting of one ball mill each with an installed power of 4.5 MW and 280 tph of mill throughput design capacity. The methodology, as described in this paper, facilitates the visualisation and quantification of plant performance and provides a good first approach to prioritise alternatives for optimisation. In a pellet plant, grinding is a critical stage due to its high energy consumption and its major impact on the physical properties of the iron pellets, which quality depends to a large extent on grind size and Blaine index. From the evaluation that was performed it can be concluded that production line 2 has the lowest specific energy consumption of 15.1 kWh/t, while line 1 has the highest with an average of 16.6 kWh/t for the same type of ore. On the basis of the results and current operational practices, it is recommended to increase the average mill throughput from 240 tph to 265 tph, translating into specific energy reduction of 10%, without affecting the chemical and physical properties of the final product. The implementation of an HPGR for regrinding the magnetic concentrate is proposed to assure adequate specific surface area in case grinding coarser becomes an alternative, which would also be beneficial for the subsequent water recovery stages. Keywords: Iron ore pelletisation, grinding circuit, energy efficiency, particle size, frequency analysis

Jan 1, 2020

By S. Banisi, M. R. Yarahmadi, S. R. Mortazavi

Nowadays the development of automatic on-line sampling systems has enabled large amounts of data to be available to plant managers. These data are inevitably prone to random and sometimes systematic errors. Data reconciliation methods are used to deal with random errors. In these methods, the measured data are adjusted in accordance to their error, so that the mass conservation law is satisfied at the same time. Measured data may also contain systematic errors, using these data in mass balancing software will result in inaccurate or even irrational results. In this paper three methods for detecting systematic errors (global test, node constraint test and maximum power constraint test) were presented. A step by step method to locate the systematic errors was demonstrated. Then, the new version of Movazen©, a mass balancing software, was introduced and used to locate systematic errors in the measurements taken from the Sarcheshmeh pilot plant copper flotation circuit. Keywords: Mass balancing, data reconciliation, random error, systematic error

Jan 1, 2020

By F. Dong, F. Yang, J. Wang, Z. Wang, D. Mingxia

Antimony oxide ores are important antimony resources, but their recovery is still a problem. In this paper, the adsorption behaviour and mechanism of dodecamine and quaternary ammonium salt on the surface of cervantite and quartz were investigated. The flotation behaviour of cervantite and quartz using quaternary ammonium salts and dodecylamine as collectors was studied by single mineral flotation experiments. The adsorbed amount was measured and infrared spectroscopy was used to study the ability of several cationic collectors to float cervantite and quartz. The results show that quaternary ammonium salts can simultaneously float the cervantite and quartz. It is difficult to achieve separation of the two minerals using quaternary ammonium salts as collectors. At pH>10, dodecylamine can float quartz but not cervantite, which can achieve reverse flotation separation of the two minerals. The difference between the abilities of quaternary ammonium salts and dodecylamine to float cervantite and quartz lies in the different ionisation properties of the two reagents. Quaternary ammonium salt is a strong electrolyte that is completely ionised in the pulp and exists mainly in the form of quaternary ammonium ions. Dodecylamine is a weak electrolyte and predominantly forms molecules under alkaline conditions. Keywords: Cervantite, quartz, dodecylamine, quaternary ammonium salts, flotation

Jan 1, 2020

By X. Cao, R. Wang, H. Han, Y. Hu, Z. Wei, W. Sun, H. Tang, J. Wang

Flotation reagents play a vital role in mineral flotation. In the past century, most studies focused on the modification of anion or cation collectors and the synergistic effect of mixed collectors, which have contributed to research. In this study, we reviewed brand-new reagents, metal-organic/inorganic complexes, with the functional group of metal ion, which are totally different from the traditional anion or cation collector and show absolute specificity for some minerals. For example, Pb-BHA complex collector was developed to realise the atmospheric flotation of scheelite due to the absolute specificity for calcium minerals. Calcium oleate collector was found to be the effective species in the flotation of calcium minerals, and has been employed to selectively separate fluorite from calcite. Selective adsorption of Al-Na2SiO3 polymer on calcite surfaces proved the self-assembly of H2SiO3 polymer using Al3+ had stronger selectively adsorption ability than Na2SiO3. Also that Fe3+-starch complex was a better depressant for iron minerals than caustic starch and contributed to a more efficient reverse flotation. In conclusion, metal ions are good templates for molecular assembly and can be used to control the structure of metal complexes and exhibit special properties, which provide possibilities for the design of new flotation agents. Keywords: Metal-organic/inorganic; flotation; collector; depressant

Jan 1, 2020

By P. M. Solozhenkin, O. I. Solozhenkin

Currently lead nitrate is used as the recommended activator in Au-Sb flotation. However, due to high levels of hazard, the application of lead nitrate constitutes a potential risk for human health and ecosystems. To mitigate the harmful impact of activators on the environment, further research on activation by alternative reagents has been launched to promote the efficiency of antimony ores. In the present study, adsorption of lead, copper and zinc cations has been investigated by nuclear quadrupole resonance (NQR), which has revealed copper and zinc cations penetration into the mineral lattice, although lead cations remain adsorbed on the mineral surface. However, the combination of zinc and copper cations leads to preferential volumetric adsorption of zinc in the mineral lattice and further surface adsorption of copper which positively affects the activation process. It has been established that activation of stibnite can be achieved effectively with the mixture of Cu2+:Zn2+=1:1 as much as with lead cations in antimony ore flotation. As a part of this work, the computational modelling has been used in prognosis of reagent activity evaluation (PRAE) for stibnite and aurostibite flotation by sulfhydryl collectors. The lower PRAE value the stronger the ability of a collector to form a stable complex with a mineral. PRAE has shown a strong negative trend to complex formation on the mineral surface of aurostibite and stibnite. Based on these studies, several collectors have been proposed for effective flotation. To verify the feasibility of proposed collectors tetramethyl (ethyl) thiuram disulfides (TMTD and TETD) have been used for flotation of stibnite, sphalerite, pyrite and arsenopyrite. Flotation performance has been improved significantly with TMTD that allows the avoidance of lead nitrate application and increases the recovery of antimony by 8,16%. Keywords: Stibnite, aurostibite, activation, lead, copper, flotation reagents

Jan 1, 2020

By J. W. Drelich, H. Zeng, L. Xie, X. Cui, Z. Gao, M. Tian, Y. Hu, W. Hu, W. Sun

Flotation is a mineral separation technology that uses the surface hydrophobic difference of valuable minerals and their associated gangue minerals to separate them. The flotation collector adsorbs on the valuable mineral surface to improve its hydrophobicity, and metal ions are usually used as activators to enhance the collector adsorption. Different mineral surfaces show different charging properties and adsorption behaviours with the collector or metal ions. Moreover, the order of adding metal ions and the collector also show significant and different flotation performance for the same mineral. The adsorption or flotation behaviour or both are governed by mineral surface chemistry, such as surface charging and reactivity. In our recent studies, force measurement using atomic force microscopy (AFM) was employed to study the surface charging and adsorption mechanism of metal ions and collectors. By preparing collector-functionalised AFM tips, AFM can directly measure the adsorption strength of the collector on the mineral surface to determine the anisotropy of mineral surface reactivity. The preparation of collector-functionalised AFM tips provides the foundation for further study of the activation role of metal ion in the collector adsorption. The application of AFM for force measurement in the surface chemistry of mineral flotation can provide important information on developing flotation reagents and lays the foundation for the specific regulation of mineral surface characteristics. Keywords: Scheelite; flotation; surface chemistry; AFM force measurement

Jan 1, 2020

By P. Pięta, A. Surowiak, T. Niedoba

In a flotation process of copper ore three factors were measured: copper grade in concentrate (β), copper grade in tailings (J) and recovery of copper in concentrate (e). The experiment was conducted by means of the Jameson cell. The factors influencing the quality of the process were particle size (d), time of separation (t), type of the collector (k) and dosage of the collector (s). The considered vector function was then [β(d, t, k, s), J(d, t, k, s), e(d, t, k, s)]. Optimisation achieved was based on determining the values of the adjustable factors (d, t, k, s). The goal was to obtain the highest possible values of functions β and e (maximum) and the lowest possible values of function J (minimum). To this purpose the taxonomic methods were applied. Keywords: Flotation, copper ore, lithology, flotation agents, particle size distribution, taxonomic methods

Jan 1, 2020

By T. Mützea, L. Schützenmeister, G. Kacheb

High-Pressure Grinding Rolls (HPGR) are employed in cement plants worldwide. Although the technology has been mastered in the majority of applications, design-, scale-up- and operationalchallenges still exist today. In addition to modelling throughput, energy requirement and comminution success, the prediction and avoidance of malfunctions is of great importance in current research. The performance of the mill is highly influenced by the roll speed and the fineness of the feed material. Another parameter influencing the composition of mill feed is the circulating load, which is determined by the grinding circuit configuration, the target fineness and the separation efficiency of the classifier. In order to meet this circumstance and simultaneously maintain a reasonable level of material input and testing effort, a complete grinding circuit on a small technical scale was set up in the research centre of Thyssenkrupp Industrial Solutions AG. The present study varied the roll speed (0.5-2 m/s) and the proportion of fines in the feed (0-75 %) in order to investigate the influence of both parameters on the finish grinding of a Portland cement with a target fineness of 4000 cm²/g according to Blain. The experimental results are compared with model concepts and critically examined with regard to their transferability to industrial plants. Keywords: Cement grinding, grinding circuit, HPGR

Jan 1, 2020

By M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmanna, G. van den Boogaart, U. Peuker

The multidimensional characterisation of processes based on various particle properties is a key requirement for a detailed prediction on certain process streams. To access the relevant particle properties (e.g. particle size, particle density and mineral content) automated mineralogy (i.e. Mineral Liberation Analyser) is applied. The kernel density estimation is used to transfer the received discrete particle data into continuous distributions without the necessity of binning the information and the related loss of information. From these continuous distributions, multidimensional separation curves are estimated. The uncertainty of these representations is tracked via bootstrap resampling. For the evaluation of the separation efficiency of the multidimensional separation curves, the statistical entropy is calculated. The statistical entropy represents a local (for each property combination) as well as a global (for the investigated property range) measure of separation efficiency and can be weighted with various property distributions (e.g. mass or mineral mass distribution) to allow for a comparison of different parameter settings and processes. With the help of a case study of a dry magnetic separation of a cassiterite bearing skarn ore from the Erzgebirge (Germany), the methodology is presented and the results are discussed in detail. Keywords: Multidimensional, magnetic separation, kernel density estimation, mineral liberation, statistical entropy

Jan 1, 2020

By G. Mahieu, L. Perez-Barnuevo, P. Barbeau-Verreault, O. Gravel

Raglan mine is a copper-nickel mining operation, part of Glencore, and located at the northern border of the province of Quebec, in Canada. The concentrator is fed by a mix of four different underground mines, thus it must accommodate periodic variations in run-of-mine mineralisation and composition. In order to concentrate nickel and copper sulphides, the flotation circuit also includes a regrind step at the cleaner stage. This leads to challenges in maintaining optimal recoveries and in diagnosing potential disturbances. This paper advocates for the combination of automated mineralogical analyses, reconciliated mass balances from diagnostic sampling campaigns and innovative multidimensional visualisation to assist in tackling these challenges. Through this approach, it has been possible to quantify the regrind step influence on the liberation of valuable mineral particles in the final flotation concentrate. The methodology also allows for virtual sieving of the products in order to track unit loss in the flotation process. The proposed analysis scheme presents an opportunity to easily diagnose flotation circuit performance based on mineralogical information. Keywords: Flotation diagnostics, multi-dimensional visualisation, mineral liberation analysis

Jan 1, 2020

AFRICAN NATIONAL COMMITTEE ON TUNNELLING In 1970, the South African Institution of Civil Engineers, the South African Institute of Mining and Metallurgy, the South African Institute of Mechanical Engineers, and the Geological Society of South Africa held an international conference on tunnelling, known as Tuncon 1970. SUID-AFRIKAANSE NASIONALE TONNELBOUKOMITEE In 1970 het die Suid-Afrikaanse Instituut van Siviele Ingenieurs, die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie, die Suid-Afrikaanse Instituut van Meganiese Ingenieurs en Die Geologiese Vereniging van Suid-Afrika 'n internasionale konferensie in verband met tonnelbou gehou, wat bekend gestaan het as Tonkon 1970.

Jan 5, 1974