Search Documents

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

By W. C. Joughin

The science of soil mechanics is 100 years old, and rock mechanics is about 80 years old. While methods of analysis and design have been developed and have evolved over time, these are relatively young sciences. The rapid increases in computing power and new technologies have enabled more sophisticated modelling and monitoring. However, there are still many aspects of soil and rock mechanics that are not well understood. Geotechnical failures, which have major consequences, still occur. These consequences may include environmental damage, major production holdups and associated loss of revenue, damage to infrastructure, and loss of life. High-consequence events, which are rare, are more difficult to anticipate and to design for, because by their nature they involve extraordinary circumstances or conditions, often geological in nature. The risks are usually mitigated by conservative designs and monitoring. Detailed geotechnical investigations help us to understand the natural variability of soil and rock masses and identify unusual or unexpected conditions. Investigating and researching major geotechnical failures is essential to enable these unusual circumstances to be anticipated. In the past, severe unanticipated events may have been treated as natural events or ‘acts of God’. However, society now has much greater expectations and it is essential to have policies and procedures in place that enable appropriate management of these rare, high-consequence risks. A good example is the Global Industry Standard on Tailings Management (GISTM), which was introduced after the catastrophic dam collapse at Vale’s Corrego de Feijao mine in Brumadinho, Brazil. The address will explain the concepts of uncertainty and variability, and how they should be taken into account in geotechnical design. The challenges facing geotechnical engineers, mine owners, and managers will be discussed. referencing a number of real case studies.

Sep 6, 2023

By P. M. Mashaba, S. O. Bada

An advanced high internal phase water-in-oil (HIP W/O) emulsion binder and flotation with an internal dispersed water phase of 95 vol% was used to beneficiate South African weathered coal from discard dumps. Five coal samples with calorific values ranged from 8.48 MJ/kg to 20.94 MJ/kg were utilized. The performance of the HIP W/O emulsion was compared to that of kerosene in terms of the physicochemical properties of the clean coal products. A 5 kg/t emulsion binder addition produced a high-quality coal concentrate with 11.76% ash and a heating value of 28.61 MJ/kg from a sample containing 29.34% ash. Using the same dose and coal sample, kerosene resulted in a clean coal concentrate with 17.47% ash and a calorific value of 26.42 MJ/kg. Further samples were also beneficiated using 5 kg/t of W/O emulsion. The highest increase in calorific value was achieved from the beneficiation of a sample containing 48.71% ash, from 8.48 MJ/kg to 18.16 MJ/kg. It has been established that emulsion binders can upgrade coal samples dumped many decades ago.

Aug 2, 2022

By T. Bruce, R. C. A. Minnitt

Mining operations are generally reluctant to install high-cost sampling systems at operations that have been functioning for many years. The principal objection to installing appropriate equipment to extract correct and representative samples in process flows is the time and costs involved. The Theory of Sampling (TOS) provides a structured framework for identifying and quantifying the errors and bias associated with any sampling event, but this may be insufficient to initiate substantial investment in correctly designed sampling equipment. Financial losses arising from substandard sampling installations are usually disregarded because the value-add from a good quality sampling solution is invisible, but the cost is quite obvious. Depending on the needs, a less-than-perfect or fit-for-purpose sampling solution may be acceptable, provided the magnitude of sampling errors is understood and the assay results are interpreted accordingly. Categorical levels of acceptable accuracy and precision can be established depending on the sampling position in the mining value chain and the nature of the decisions to be made. The objective benefits of proposed fit-for-purpose sampling solutions should be presented to relevant decision-makers in such a way that adverse subjective decisions are countered so that appropriate solutions are implemented. Practical examples of the benefits from motivating the implementation of fit for purpose sampling solutions at sampling facilities around the world are provided.

Jul 2, 2022

By C. Ndou, T. Mothupi, H. Mandende

The technological advances in efficient, rapid, and non-destructive hyperspectral core logging systems for systematic mineral mapping have led to the discovery and exploitation of new mineral deposits Hyperspectral imaging in the long-wave infrared range has been recently used successfully to identify various phosphatebearing minerals (monazite, xenotime, and britholite), with limited work on apatite associated with mafic-ultramafic layered intrusions. In this study we investigate the effectiveness of a hyperspectral imaging (HSI) system with long-wave infrared (LWIR) bandwidthsto identify apatite in the Upper Zone of the Bushveld Complex. The accuracy of the HSI results was validated by mineralogical and geochemical data. The two apatite-enriched zones detected by HSI suggesting widespread development of apatite throughout the uppermost 600 m of the Upper Zone. The lower apatite-enriched zone is approximately 40 m thick, while the upper apatite-enriched zone is about 23 m thick, consistent with previous thickness determinations by traditional logging and analytical methods. Spectral mixing observed in the response of apatite is ascribed either to the common association of apatite and olivine in these rocks, or to differences between the spatial resolution of the hyperspectral image and the size of apatite grains. The VNIR-SWIR wavelength region did not show prominent spectral features of apatite. Nonetheless, HSI in the LWIR range is effective in mapping apatite and should therefore be considered as an exploration tool. This research advances our knowledge of the reflectance spectroscopy of REE-bearing minerals, which makes it easier to detect, identify, and quantify REE-bearing silicate minerals by HSI.

Feb 6, 2023

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By F. Hörtkorn, Y. Narainsamy

Rather quietly, a new generation of European norms dealing with earthworks has been developed over the past few years, in particular a part of EN 16907 pertaining to extractive waste. Whereas the majority of the parts deal with routine geotechnical aspects, one part deals specifically with tailings dams. The standard is currently in draft form but if this becomes a European Standard, members of the European Union are bound to comply with the regulations. As such, the standard has the capacity to influence mining in Europe and potentially in South Africa. In this paper we review the standard and compare it to the South African standard on mine residues and the recently published Global Industry Standard on Tailings Management (GISTM). We conclude found that although the European norm makes great strides towards increasing tailings dam safety, there is room for improvement. The current South African standard has served well since its inception, but can be improved by using concepts from the European and global tailings standards.

Jun 2, 2022

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

By A. Atta-Quayson

Since 2012, Ghana has been implementing local procurement regulations in the mining sector to broaden and deepen linkages between mining and other sectors of the economy. The regulations have been implemented in collaboration with the mining industry. This paper offers an in-depth analysis of how the local procurement regulations and related initiatives have been implemented so far. Primary data gathered with semi-structured interviews and secondary sources of data indicate a steady improvement in both in-country procurement and local manufacturing of inputs for the mining industry. There are, however, some challenges relating to tariff structure and support (financial and technical) for local suppliers and manufacturers to meet high standards and demands of the mining industry. This calls for a well-thought-out strategy and programme of activities to sustain and improve on progress made.

Feb 2, 2022

By G. Jandieri

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling industrial waste. The methodology is based on the break-even control mechanism, but at the same time provides for the introduction of new evaluation criteria such as the threshold of conditionality and the degree of ore substitution. Based on an improved analysis, it becomes possible to more precisely predict recycling efficiency. A more refined determination of the lower limit of concentration of recoverable metals, at which technogenic waste can be assigned the status of secondary raw materials and processed profitably, leads to a significant expansion of the secondary raw material base suitable for recycling. The potential for recycling manganese-containing dust from the production of ferrosilicomanganese, dehydrated sludge from the hydro separation of slags, and cake from the production of electrolytic manganese dioxide at the Chiatura mining enterprise is used as an example. It is shown that with a threshold of –24% Mn content, the highest recycling efficiency can be achieved by the production of low-phosphorus manganese slag and conversion to ferrosilicomanganese using the above waste to replace 40-60% grade III and IV manganese concentrates in the feed.

Jan 26, 2023

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

By D. F. Malan, D. Ile

This study explores the use of backfill in hard rock bord-and-pillar mines to increase the pillar strength and extraction ratio at depth. The use of backfill will also minimize the requirement for tailings storage on surface and the risk of environmental damage. A literature survey indicated that backfill is extensively used in coal mines, but rarely in hard rock bord-and-pillar mines. To simulate the effect of backfill confinement on pillar strength, an extension of the limit equilibrium model is proposed. Numerical modelling of an actual platinum mine layout is used to illustrate the beneficial effect of backfill on pillar stability at greater depths. The magnitude of confinement exerted by the backfill on the pillar sidewalls is unknown, however, and this needs to be quantified using experimental backfill mining sections equipped with suitable instrumentation.

May 3, 2023

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By P. W. J. van Rensburg

Our mineral heritage - PRESIDENTIAL ADDRESS given by P. W. J. van Rensburg, Pr. Eng.. B.Sc. (Eng.)(Rand) INTRODUCTION Stone Age people were living in various parts of South Africa as recent,ly as a thousand years ago, when they were displaced by Iron Age people with a culture developed in the far north. These invaders brought farming, building, and the earliest mining developments to the Transvaal, thus ushering in the beginning of our great mineral heritage. It is of particular interest to record that, up to comparatively recent times, some of these people were excavating iron-bearing shale rocks for their smelting furnaces on the Melville Koppies in J ohannesburg. Although the most recent the iron-smelting furnaces discovered on these koppies is estimated to be some five-hundred years old, it believed that these Iron Age people were driven out, and their settlements destroyed, by Zulu impis only one-hundred-and-fifty years ago.

Jan 10, 1973

By John Freer

On 25th November, 1983, nearly forty members of The South African Institute of Mining and Metallurgy, together with Doris Gardner and Judith Money from Kelvin House, travelled by luxury motor coach to Secunda, there to visit the coal-mining and conversion operations of Sasol Limited.

Jan 1, 1984

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023