Search Documents

By R. G. Bottge

To better understand those factors which increase mining costs in Alaska, a Bureau of Mines study was conducted to compare the estimated costs of operating a 100,000-tpd open pit copper mine located on a hypothetical ore body in the Lake Clark area, Alaska, with the costs of mining a similarly sized hypothetical copper ore body near Tucson, Ariz. The information derived should be beneficial to the State and Federal governments in appraising the potential for development of large, low-grade porphyry copper deposits in south-central Alaska. Conventional mining and concentrating methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The total price required for copper mined in Alaska and Arizona was $1.12 and $0.63 per pound, respectively, plus or minus 20 percent. These values were obtained assuming no leaching of low-grade copper, recovery of gold, silver, and molybdenum as byproducts, 100-percent equity financing, and a 12 percent discounted cash flow rate of return. The average domestic and international prices for copper in July 1973 were $0.60 and $0.916 per pound, respectively. The existence of a developed transportation and power system in Alaska would have reduced capital and operating costs subs tantially. The required price for copper would have declined from $1.12 to $1.05 per pound, plus or minus 20 percent.

Jan 1, 1974

By D. D. Bolstad

This report describes the construction and use of a direct-reading azimuth protractor (DRAP) by the Bureau of Mines for measuring fracture orientations in mines, tunnels, or other excavations having a magnetic environment. The DRAP allows a rapid and simultaneous measurement of dip and azimuth of dip of a fracture plane. The instrument is rugged, lightweight, and easily constructible from standard hardware items. The DRAP can measure dip to within ±0.5° and azimuth of dip to within ±5° of corresponding values obtained with a Brunton compass.

Jan 1, 1974

By R. Ward Stahl

This publication is a revision of Report of Investigations 5363 updated to reflect the improvement in fire protection at selected coal mines and contains suggestions on what may be considered good fire protective equipment, suggested methods of organizing the attack on fires at various locations underground, and helpful hints on testing and evaluating firefighting facilities.

Jan 1, 1968

By C. W. Owings

The Bureau of Mines has conducted a survey to determine potential exposure of mine workers to dust produced in connection with intermittent rock drilling in coal mines. Eighteen mines in 3 states were visited, and 30 different operations were observed, as follows: 10 drilling in draw slate, 8 drilling top rock for brushing or grading, 2 drilling in the coal face, 4 drilling in the bottom, 2 drilling top rock for overcasts, 2 drilling in faults or boulders, 1 drilling for roof bolting, and 1 drilling for trolley hangers. Dust respirators were worn by drilling crews during 16 of the 30 operations. Three hundred thirty-two samples of air-borne dust were collected during the survey. ACKNOWLEDGMENTS The information in this report is based on samples collected and observations made in bituminous-coal mines. Operating officials at these mines have contributed to this study, and their cooperation is gratefully acknowledged. All samples were counted by Thomas B. Kirby, chemist, and Dominick A. Ambrosia, scientific aid, and were analyzed by Gretta S. Baur, physicist, and Patricia M. Gussey, scientific aid, of the Health Branch of the Bureau of Mines.

Jan 1, 1953

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

Enable mine personnel to determine the effectiveness of and to optimize the mine fire stench warning system without resorting to costly trial and error fire drills. Approach The mine fire stench warning system is used by underground metal/nonmetal mines to warn mine workers of a fire or other emergency. Stench is released directly into the mine ventilation and/or compressed air lines, and its repulsive odor warns miners to evacuate the mine or to follow other established emergency procedures. Unfortunately, since most deep metal mines have complex ventilation systems, some areas of the mine may receive nauseatingly high concentrations of stench while other areas, in more remote locations, may receive no warning or greatly delayed warring at best. The Bureau of Mines, through research, endeavored to solve this problem with a computer modeling system designed to calculate the distribution of odorant by the stench warning system.

Jan 1, 1986

By M. J. Ankeny

The expression "firing open, unconfined shots," as used in this circular, means the firing of explosive charges not confined in boreholes. Examples are the so-called mudcap shots, adobe or dobe shots, or bulldozing shots consisting of explosive charges placed on, under, or between rocks for the purpose of breaking them. The practice of firing open, unconfined shots is not uncommon in coal mines, despite the fact that numerous mine explosions and dust ignitions have resulted from this practice. The usual method of preparing such shots is to place the explosive with its detonator on top of a piece of rock or coal and cover it with clay, loam, sand, or road dust; frequently no covering of any kind is used. In some mines, an open charge of explosive is placed on timbers to dislodge them or in crevices in the roof to break down loose rock that cannot be dislodged with a bar or pick. The explosive charges may be made and fired singly, although sometimes several charges are placed on one large piece of rock with a detonator in each charge, and all charges are fired simultaneously. Although it is general practice to use permissible shot-firing devices, which will not ignite gas or dust to fire these charges, electric power from the regular mine circuits is sometimes used. When the shot is fired, any coal dust that may be present is thrown into suspension by the blast and may be ignited by the intense hot flame of the explosive or by an arc or spark at the leg wires or the end of the firing leads if power from the regular mine circuit is used to fire the shot. Even if there is not enough coal dust present to form a dust cloud, open, unconfined shots can readily ignite methane.

Jan 1, 1952

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

Determine the effectiveness of remining operations in reducing contaminant load (acidity, iron, and sulfate) of discharges emanating from abandoned surface and underground coal mines. Background Until the implementation of remining initiatives, most States had regulations that held the operator remining an abandoned site responsible for preexisting acid mine drainage (AMD) discharges. For example, if a mining. company wanted to remine an area hydrologically connected to an existing AMD discharge, the company became responsible, as soon as the site was activated, for treating that discharge to meet effluent standards. If the mining operation improved the quality of the discharge, but the discharge failed to meet effluent standards, the company was held accountable for perpetual treatment. Because of this regulation, most mine operators avoided abandoned sites with minable coal reserves and AMD discharges. However, changes in remining legislation allow coal companies to be released from treatment liability as long as the post-remining pollution load does not exceed the pre-remining level. If remining can improve water quality through improved mining and abatement techniques, abandoned mine land (AML) areas that previously were liabilities could become

Jan 1, 1994

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By Fred D. DeVaney

Copper sulphate is a common flotation reagent for blonde ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation food may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it, is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss. That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.

Jan 1, 1929

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials for removing metal contaminants from waste waters. The beads, designated as BID-FIX beads, are prepared by blending biomass, such as sphagnum peat moss or algae, into a polymer solution and spraying the mixture into water. Laboratory studies were conducted to determine bead sorption and elution characteristics. Batch and continuous tests demonstrated that BIO-FIX beads sorbed arsenic, cadmium, lead, and other toxic metals from acid mine drainage waters collected from several sites. Selectivity for heavy and toxic metal ions over calcium and magnesium was demonstrated. The beads exhibited excellent metal sorption and handling characteristics in stirred tanks, column contactors, and a low-maintenance passive system. The sorption process was reversible, and metal ions were eluted from the beads using dilute mineral acids. Cyclic tests indicated that the beads continued to extract metal ions after repeated loading-elution cycles.

Jan 1, 1991

Improve the reliability and accuracy of subsurface images using constrained tomography with enhanced ray-tracing capabilities. Background Geophysical tomography is a technique for imaging the structure of a rock mass using seismic or radio waves, in the same way that medical CAT scans image human tissue using X-rays. Tomography has found numerous practical applications related to mining, including lithologic and structural characterization, fracture detection and fluid monitoring, void detection, and evaluation of stress state and integrity of mine structures. Problems Two fundamental problems have largely prevented geophysical tomography from enjoying the tremendous success achieved by medical tomography. The first is a consequence of practical limitations on the placement of sources and receivers of wave energy: ideal resolution can be attained only when the region being imaged is entirely surrounded by sources and receivers, so that it is crossed by rays traveling in all possible directions. When such coverage is impossible or impractical, the inversion becomes underdetermined: there id not enough information in the measured data to provide a mathematically unique solution. The second major problem in geophysical tomography is the necessity for detailed ray tracing. Commercial software, as well as previous U.S. Bureau of Mines (USBM) software, employs a ray-shooting algorithm that may be unable to model some ray paths when velocity contrasts are larger than about 100%. These ?shadow zones" result in loss of data and degradation of reconstructed images.

Jan 1, 1994

By H. R. Beard

The citrate process for sulfur dioxide emission control was developed in pursuit of the Bureau of Mines goal of minimizing the adverse environmental impact of mineral-processing operations. This publication describes the gas analysis procedures used during development of the process. The research required the capability to analyze SO2, H2S, CO, CO2, COS, volatile hydrocarbons, NO, NO2, O2, N2, and H2. The methods described include gas chromatography, electrochemical detection, infrared spectroscopy, and the use of a computer program to predict the product composition in complex reactions. Laboratory and pilot plant applications are discussed.

Jan 1, 1979

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

By Raymond P. Maloney

The Bureau of Mines investigated the White Mountain mercury deposit, in the Kuskokwim River Basin, to better determine the extent of mercury mineralization and to encourage its development by private industry. A program of diamond drilling, augering, bulldozer trenching, and sampling was carried on during four field seasons, from 1960 to 1963, inclusive. Significant amounts of cinnabar, with only trace amounts of arsenic and antimony, occur in dolomite over an area about 4,000 feet long and 1,500 feet wide. The deposit differs from other mercury deposits in the Kuskokwim River Basin by the absence of silica-carbonate and rhyolite intrusives. Small-scale mining was started in 1963 as the result of Bureau investigation and continued during the summers of 1964 and 1965. The investigations indicate that open pit mining might be the most feasible method of working this deposit.

Jan 1, 1967