Search Documents

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By Arne Landsberg

Experiments were made with a batch reactor to determine the effect of gas pressures, temperature, and gamma radiation intensity on the reaction CO + Ch ? COC12. The equation, [dp = 0.0110 (1 - 0.01t) (PCOI)1/2 PC12] where [dP] is the change of pressure of phosgene with time (atm/hr), t is the temperature (°C), PCO and PC12 are the reactant pressures (atm), and I is the radiation intensity (r/hr), was found to best fit the data. Oxygen and a large ratio of reactor surface to volume retarded the reaction, but inert gases had no effect. A low-temperature reactor system is proposed to take advantage of the conditions which give a high reaction rate with gamma radiation and a simple scheme of product purification.

Jan 1, 1970

By Oliver Bowles

Limestone is the most widely used of all racks and is essential to a great many industries, including tae building trades, highway construction, metallurgy, agriculture, end many chemical and manufacturing enterprises. It occurs in some form in every State and is produced in thousands of quarries. Production in 1930 exceeded 134,000,000 tons. It has more numerous and more diversified uses than any other rock. This paper is designed to furnish general information on the various branches of limestone quarrying and their economic importance. Brief reference is made to dimension stone, and a more complete discussion follows of the uses, requisite qualities, quarry methods, grid processes of preparation of crushed and broken limestone. Footnote references serve to guide the reader to more detailed information.

Jan 1, 1933

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

By Allan J. Clark

This paper, describing the milling practice of the Homestake Mining Co., is one of a series being prepared by the Bureau of Mines. The author acknowledges the assistance of T. G. Chapman, one of the consulting engineers of the Bureau of Mines, in arranging this paper for publication.

Jan 1, 1931

By Roy H. Grau

Increased awareness of a healthy work environment is common to all industries and the stone industry is no exception. The presence of operating diesel equipment, welding, stone production blasting, and silica dust in a working environment all contribute to air quality issues in underground stone mines. Particularly recognized is the exposure of workers to diesel particulate matter (DPM). Recent regulations call for a DPM standard of 160TC ug/m3 (TC = Total Carbon). The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of these mines and consequently reduce the exposure of workers to harmful airborne contaminants. The results have shown that the ventilation of underground stone mines can be significantly enhanced using improved ventilation controls and techniques. Large-opening stone mines present specialized ventilation challenges because their entries are much larger than in other types of mines. Most stone mines have entries about 40 feet wide and up to 30 feet high, with bench areas that may extend even higher. These large entries present the positive opportunity to move large air quantities at relatively low mine fan pressures resulting in lower fan horsepower and reduced operating costs. However, the difficulty in ventilating large-opening mines is that even with large air volumes, the air velocity is often less than 100 feet/minute. Higher ventilation velocities more quickly dilute and remove contaminants from the face areas. Higher ventilation airflow velocities can be achieved by effective ventilation planning and proper choice of ventilation fans.

Jan 1, 2009

By H. E. Powell

Over 5 million lb of chromium, 1 million lb of nickel, and 90,000 lb of molybdenum are lost annually in the dusts generated in the production of stain-less steel. Additional losses of these metals in the form of mill scale and grinding swarf may be double the dust losses. This Bureau of Mines report describes a process for recovering these and other metals in the form of an alloy steel suitable for recycling. Zinc and lead, when present in the wastes, are recovered as byproducts in the form of oxide fumes. The laboratory-scale process (10-to 25-lb charges) recovers up to 95 pct of the chromium, 100 pct of the nickel, and 100 pct of the iron. The resultant alloy contains from 10 to 20 pct chromium, 6 to 12 pct nickel, and 55 to 65 pct iron, with lesser amounts of molybdenum and manganese. The alloy is essentially free of zinc, lead, and sulfur. The zinc-lead fume obtained from the treatment contains about 40 pct zinc and 20 pct lead and represents essentially complete recovery of these metals.

Jan 1, 1975

By E. R. Cole

A lead smelting process that appears to present minimal pollution problems has been developed at the Bureau of Mines, Rolla Metallurgy Research Center. Ten and 100 g samples of PbS mill concentrates were vaporized at 1,000° to 1,100° C in a furnace with an inert gas atmosphere during a 2-hour period. The PbS vapor was transported by the inert carrier gas to the reduction zone of the furnace where it was reduced at the same temperature with excess hydrogen to metallic lead. Lead of 99.9 pct purity was produced. The H2S formed can be decomposed into elemental sulfur and water vapor by a modified Claus process. Approximately 90 pet of the Cu and 70 pct of the Ag and Zn remain in the residue and are potentially recoverable. More than 98 pct of the lead in the concentrates was extracted.

Jan 1, 1974

By Kevin A. Rider, Bernard J. Martin

Reaching movements are planned and subsequently executed [1] using visual and somatosensory feedbacks [2], where absence of visual feedback is known to increase endpoint variability [3]. Visual occlusion decreases the ability to make rapid online compensatory movements, which results in initial radial deviations that are highly correlated with radial dispersion at the target. Perturbations of rapid, visually-guided reaches are compensated on-line and result in endpoint dispersions poorly correlated with initial deviations, emphasizing the strong effect of visual feedback in temporally-constrained reaching tasks. In control conditions (no vibration), these uncompensated, rapid reaches serve as estimates of the individual’s intended trajectory. When ride motion is present, trajectories of rapid, visually-occluded reaches provide a measure of the natural biodynamic response of the cantilevered spine-arm-hand linkage. These intended movement trajectories and the biodynamic response (vibration feedthrough) are used to predict the effect of ride motion on the performance of rapid reaching tasks. Goals of this study are to investigate the influences of vehicle motion on human reaching and pointing, and to reveal movement strategies used in visually-occluded reaching tasks. Methods A six degree of freedom human-rated Ride Motion Simulator (RMS) was used to generate a dynamic vehicle environment. Participants performed discrete, rapid pointing tasks to targets presented on three touchpanel displays under stationary and random whole-body vibration. Reach instructions included successfully reaching identical circular targets (Ø = 0.25”) with the right index fingertip as fast as possible. Targets were presented on resistive-touch displays mounted approximately 60 cm from the participant’s nasion. The touchpanel displays were located in the forward and lateral directions at eye level, and forward at 45° of elevation. These displays measured the spatial error of the reach destination. A ten-camera VICON motion capture system recorded the upper body kinematics of the participant. Reflective markers were placed on the participant’s torso, head, and arms. Initial kinematics of the fingertip (i.e. time and magnitude peak tangential velocity) and tangential velocity at target were used to estimate the planned endpoint of the reach. Results and Discussion Ride motion resulted in increased endpoint variability compared to reaches performed in the stationary condition. Reaches to the elevated touchpanel consistently resulted in the largest variability across all motion conditions, suggesting that a vehicle occupant would not be capable of accurately activating a control in that location. Principal axes of endpoint ellipses were along and perpendicular to the direction of fingertip movements. Example graphs of endpoint variability with ellipses containing 95% of the data points are shown in Figure 1. These ellipses

Jan 6, 2006

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor'ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t'le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By Carl F. Wingquist

In support of Bureau of Mines studies of thermal fragmentation of rock, the elastic moduli of four types of rock were measured at temperatures ranging from room temperature up to 1,500° F (1,089° K). The sonic method was employed to determine the resonant frequencies of the rock specimens and from these frequencies, the elastic moduli were calculated. Data for Young's modulus, shear modulus, and Poisson's ratio are given as a function of temperature for Dresser basalt, Reserve taconite, Jasper quartzite, and Charcoal granite. Young's modulus and the shear modulus decreased with increasing temperature up to about 1,200° F and then became relatively insensitive to temperatures from 1,200° to 1,500° F.

Jan 1, 1969

By R. A. Isberg, D. A. Parrish, H. Kramer

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75% coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 3, 1981

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

By Thomas P. Mucho

Cable bolts are emerging as the newest ?twist? for roof support in U.S. underground coal mines. For decades cable bolts installed in underground metal mines in the United States and Canada used cement-based grouts for anchoring. The cement anchoring process, because of the time and expense for installation, made cable bolts impractical for use in coal mines. Today, the introduction of resin-anchored cable bolts provides a system more consistent with tradi­tional U.S. coal mine roof bolting practices and requirements. Expecta­tions are that the utilization of cable bolts for a number of U.S. mining applications will expand, particularly in coal mining.

Jan 1, 1998

By Laurance L. Oden

Titanium-enriched smelter slag produced commercially by Quebec Iron and Titanium Corp., Sorel, Quebec, was evaluated as feed material for a process developed by the Bureau of Mines to prepare rutile. Glass-forming agents including P205, B203, and two binary mixtures were added individually to the as-received and preoxidized smelter slag, and the nonferrous tramp oxides were effectively partitioned into the resulting noncrystalline phase. Iron in the ferrous oxidation state was moderately soluble in the glass of reduced specimens but less soluble under oxidizing conditions. The solubility of iron oxide in phosphate glass exceeded the solubility of iron oxide in borate glass. Effective conversion of titanium oxide to rutile was not achieved in the high-iron commercial smelter slag, and 20 to 30 pct of the titanium remained as pseudobrookite, a mixed iron-titanium oxide.

Jan 1, 1973

By E. D. Gardner

About 300 tons of gold ore per week was being produced in February 1934 by Thomas D, Herron and Con Laster from the old lake Superior and Arizona workings; the ground was leased from the Magma Copper Co. The workings adjoined but were not a part of the Magma mine. The lessees had been employees of the Magma Copper Co, at the time the Magma closed down for the summer of 1932. Work on the lease began in July 1932 on an exposure of $2-per-ton ore disclosed in a drift; after a few hand-drilled rounds were blasted the gold content increased to about $30 per ton. Extensive sampling by pannings elsewhere of exposed portions of the vein indicated that other ore shoots existed. The last work previously done in the mine was during the World War, when lessees mined a number of small shoots of copper ore. In some of the stapes the copper miners had left a quartzose streak on the hanging wall that carried $15 per ton of gold. This material did not look as if it cried values and evidently never had been sampled. The first shipment of gold ore was made on September 28, 1932. Up to April 1, 1933, 3,778 tons had been shipped and from September 1, 1933, to January 31, 1934, 3,125 tons.

Jan 1, 1934

By J. M. Kuchta

Ignition and flammability test methods were developed by the Bureau of Mines for use in the classification of flammable solids by the Department of Transportation. A rotating disk ignition apparatus and a flame-spread-rate apparatus are proposed for determining the ignitability and flammability, respectively, of most flammable solids. Extremely flammable solids, such as pyrophoric materials, are evaluated by determining their ease of spontaneous ignition in an environmental chamber at high-humidity conditions. Data are presented for various representative solids to show the reliability of the test methods for classifying the materials. A classification system is also proposed for use in government transportation regulations.

Jan 1, 1972

This surveillance report summarizes data on work-related fatal and nonfatal injuries, illnesses, and hazardous exposures in the mining industry for the 10-year period 1986-1995. The term ?surveillance,? as used in public health, may be new to many readers of this report. With regard to occupational safety and health, the goal of surveillance is to describe the occurrence of work-related injuries, illnesses, and known hazardous exposures; to identify new hazards that may occur due to the introduction of new technology or other factors; and to assess the effects of preventive measures designed to improve worker safety and health. Surveillance provides an overall picture, which can be used to focus resources on areas most in need of prevention programs or further research. Surveillance generally requires the use of multiple sources of data, all of which have their own strengths and limitations. Surveillance in the U.S. mining industry is complicated by the fact that U.S. national data systems that provide information on mining are based on two different definitions of the mining industry. One is established by the Mine Safety and Health Administration (MSHA), the other by the Standard Industrial Classification (SIC) System [Office of Management and Budget 1987] and the 1980 U.S. Bureau of the Census (BOC) Classification System [U.S. Bureau of the Census 1982].

Jan 1, 2000

By Thomas H. Dubaniewicz

Thirteen miners died as a result of 2 explosions in the Jim Walter Resources No. 5 mine near Brookwood AL in September 2001. Both explosions were ignited in intake air entries, and both were probably ignited by electrical equipment. With few exceptions, permissible equipment is not required in intake air entries of US underground coal mines Researchers with the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. studied the electrical equipment ignition sources for the Brookwood and other w disasters to develop recommendations for preventing similar disasters Adherence to National Electrical code® requirements for flexible cords installed in hazardous (classified) locations may have prevented the second massive Brookwood explosion. The 30 CFR Part 7 requirements for battery assemblies should be reevaluated, taking into consideration United Mine Workers of America recommendations and the Zone 1"increased safety" standard requirements for battery assemblies, Class 1 Division 2 or Zone 2 explosion protection techniques are recommended for intake air equipment so that they do not present a methane air ignition source under normal operation before mine power is shut down during emergencies Battery powered circuits intake air that are likely to remain energized during emergencies should be protected by more stringent protection techniques, to protect rescue/recovery personnel. Index Terms -Class 1 hazardous location, mine explosion, flexible cord, battery assembly, permissible equipment