Search Documents

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986

By L. S. Harner

This paper which describes the milling practice at the Golden Cycle mill is one of a series of similar papers being prepared by the United States Bureau of Mines. The mill of the Golden Cycle Corporation, formerly known as the Golden Cycle Mining and Reduction Co., is located at Colorado Springs, Colorado, and has been operated since 1907. It is now and has been from its inception almost exclusively a custom mill.

Jan 1, 1933

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By Martin H. Stanczyk

Bench scale, laboratory batch attrition grinding tests were made of a coarse commercial kaolin in a stainless steel, 5-inch-diameter attrition grinding machine to study the effect of a number of basic operating variables on particle size reduction and electric energy consumption. The results of the investigation showed that the more important operating variables influencing the efficiency of kaolin comminution and energy consumption requirements were type, size, and shape of grinding media, grinding media to clay weight ratio, peripheral rotor speed, clay slip pulp density, degree of pulp dispersion, and the angular arrangement of the rotor and stator bars. The tests also indicated that variables having less influence on grinding efficiency and energy consumption were pulp temperature, design of rotor cage, rotor clearance, rotor-stator bar interval, addition agents, pulp level, degree of pulp aeration, and chamber liners. The research showed that grinding media had the greatest influence on abrasion of machine parts and that spherical-shaped grinding media were superior to sharp angular or long bladed media with respect to media degradation, machine abrasion as well as grinding efficiency.

Jan 1, 1968

By John E. McCullough

The purpose of this development program is to design and develop a known volume air sampling pump for use in measuring the amount of radio-active material in the atmosphere of an underground uranium mine. The principle nuclear radiation hazard to underground uranium mines comes from the mine atmosphere. Daughter products of 222-radon, namely 214-polonium, 214-lead, 214-bismuth and 214-polonium, are inhaled by the miner, resulting in a relatively high lung cancer rate among these workers.

Jan 1, 1976

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940

By Seth C. Scharfer

"As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the Gibbs energies of formation of MoS2 (molybdenite) and WS2 (tungsten disulfide) were determined with high-temperature galvanic cells employing stabilized Zr02 (zirconia) as the electro¬lyte. In the temperature range from 867 to 1,209 K, potential measurements were obtained for the cellPt, MoS2 , Mo02 , SO2 = 1 atm // Zr02 // 02 = 0.0112 atm, Pt, with the overall cell reactionMoS2(c) + 3 02(g, 0.0112 atm) = Mo02 (c) + 2 S02(g). (1)These results, combined with the best available values for Gibbs energies of formation (?G°f) of Mo02 (molybdenum dioxide) and SO2 (sulfur dioxide) from the literature, give the standard Gibbs energy of formation of MoS2, ?G°f, for the reactionMo(c) + S2(g) = MoS2(c) (2)?G°f = -96.681 + 43.76 x 10-3T±0.538 kcal/mole, (3)where temperature (T) is expressed in Kelvins.Similar measurements in the temperature range from 872 to 1,210 K were obtained for the cellPt, WS2 , W03 , SO2 = 1 atm // Zr02 // 02 = 0.0114 atm, Pt, with the overall cell reactionWS2(c) + 3.5 02(g, 0.0114 atm) = W03 (c)+ 2 S02(g). (4) Combination of these results with the best available data of ?G°f for W03 (tungsten trioxide) and SO2 from the literature gives the Gibbs energy of formation of WS2 in the temperature range from 872 to 1,210 K for the reactionW(c) + S2(g) = WS2 (c)(5)?G°f = -92.429 + 43.88 x 10-3T ± 0.280 kcal/mole. (6)A third-law analysis yields a standard enthalpy (?H°f) for the reaction298Mo(c) + 2 S(rh) = MoS2(c), (7)?H°f = -67.36±0.60 kcal/mole, (8)298where the standard states are pure crystalline MoS2 / and rhombic sulfur."

Jan 1, 1980

Coal is a combustible, carbonaceous, sedimentary rock that is formed by the accumulation, compaction, and physical and chemical alteration of vegetation [Simon and Hopkins 1981; Bates and Jackson 1987]. Coal is classified according to its type, grade, and rank. The type of coal relates to the plant materials from which the coal originated. The grade of coal refers to the purity of the coal-or the amount of inorganic material (including ash and sulfur) left after the coal is burned [Bates and Jackson 1987; Stefanko 1983]. The rank of coal indicates its degree of metamorphosis and roughly correlates to the geological age of the coal or the geological environment from which it has been mined [Bates and Jackson 1987]. Rank also indicates the percentage of carbon in dry, mineral-free coal [Whitten and Brooks 1973] and the degree to which the coalification process has progressed [Larsen 1981]. The geological process of coalification begins with organic materials (e.g., celluloses, lignins, and other plant compounds that are deoxygenated and then dehydrogenated) and ends with coal of various geological ages, from lignite to anthracite [Larsen 1981]. Table 3- 1 presents the American Society for Testing and Materials (ASTM) classification of coals by rank. According to Parkes [1982], high-rank coal includes anthracite and semianthracite coal ("hard coal," with 91% to 95% carbon); intermediate-rank coal includes low-, medium-, and high-volatile bituminous and sub-bituminous coal ("soft coal," with 76% to 90% carbon); and low-rank coal includes lignite (with 65% to 75% carbon or less). The rank of coal tends to increase from the western to the eastern United States, with anthracite occurring primarily in eastern Pennsylvania [Schlick and Fannick 1971]. Most of the coal currently mined in the United States is bituminous [Given 1984]. A classification of the coal in the United States is provided in Table 3-2.

Jan 1, 1997

By John C. Machisak

THE INJURY data and related employment experience of the coking industry in the United States for 1955 arc presented in this publication under the following general sections: (A) General Injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, injury-frequency rates, and accident agencies involved in causing injuries. Data are tabulated for the industry as a whole, for each typo of oven: and for the States in which coke is produced.

Jan 1, 1958

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

By Robert W. Geehan

The Bureau of Mines developed, by core drilling, the property of Nevada Scheelite, Inc., from October 5, 1943, to February 24, 1944. Claims of the corporation are near Rawhide in the northern portion of Mineral County, Nev. The purpose of the work was to determine possible reserves in the lateral and vertical extensions of a tactite zone which was being mined for scheelite. Production from this zone to January 1, 1944, was said to be 64,500 tons, with a recovery of 50,618 units of tungsten trioxide. The development work was done by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, mapping the areas, and exploring the deposit by diamond drilling, trenching and sampling. Eleven holes were drilled for a total footage of 2,365 feet of holes.

Jan 1, 1950

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933

By H. P. Holmes

Tonnage quantities of hafnium metal have been prepared in Kroll-process equipment designed for producing zirconium. Some slight process modifications have been necessary, but overall operation is the same as for zirconium. Hafnium oxide is chlorinated in the presence of carbon and the resultant hafnium tetrachloride reduced by magnesium metal. Byproduct magnesium chloride is removed in a high-vacuum distillation step and the hafnium sponge metal crushed for further use. Arc-melted metal can be forged and rolled to sheet, but the best material produced to date would not be considered cold ductile. INTRODUCTION This investigation is part of the program for the production of pure metals from domestic and foreign ores that has been underway at the Bureau of Mines for several years. It was done in cooperation with the Atomic Energy Commission and the Bureau of Ships.

Jan 1, 1955

The National Institute of Occupational Safety and Health has classified diesel exhaust as a potential human carcinogen. Though standards for diesel particulate matter (DPM) in the work place have not been established, concern for the health of miners is prompting mine operators to consider methods for reducing worker exposure to diesel exhaust. Approach One of many methods for reducing DPM being investigated by the Bureau of Mines is the use of additives in diesel fuel to improve combustion. Research Results Three fuel additives have been tested in Caterpillar and Deutz diesel engines which are similar to types used in underground mines. One iron-based additive containing ferrous picrate had no effect on emissions. A second iron-based additive containing ferrocene reduced DPM between 5 and 45 pet depending on engine operating conditions. The 37-pct reduction for an 8-minute duty cycle, which includes a wide range of transient loads and speeds, is considered to represent in-mine performance.

Jan 1, 1990

By Eric E. Cather

A mineral survey of the Fisher Gulch RARE II area (A5299), Trinity County, California was conducted by the U.S. Bureau of Mines and U.S. Geological Survey. The Bureau of Mines was responsible for detailed examination of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. The area is underlain by the Salmon Hornblende Schist. Tonalite stocks 1.5 mi (2.8 km) to the east and northeast of the area intrude the schist and are closely associated with the nearby nines (Cox, 1967). The mines have quartz veins containing sulfides and gold in shears trending east to north past in the schist and tonalite (Hotz, 1972). Strewn and terrace gravel s occupy most of the drainages, many have yielded substantial quantities of gold.

Jan 1, 1981