Search Documents

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006

By James Westfield

Following is a brief history of Bureau of Mines Division of Coal-Mine Inspection activities that have favorably effected health and safety and reduced Injuries at coal mines: The Federal cline Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines for the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consulting with representatives of management and mine workers, and was incorporated in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, betweeen the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines considered imminently dangerous, but authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1962

The National Personal Protective Technology Laboratory (NPPTL) of the National Institute for Occupational Safety and Health (NIOSH) has undertaken a collaborative study with the Mine Safety and Health Administration (MSHA) to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), withstand the underground coal mining environment with regard to both physical damage and aging. Apparatus tested included the CSE SR-100, the Draeger OXY-K Plus, the MSA Life-Saver 60, and the Ocenco EBA 6.5 and M-20. This report presents findings regarding laboratory-tested SCSRs in the tenth phase of testing, from July 2004 to March 2006. The SCSRs were tested on a breathing and metabolic simulator and on a human subject walking on a treadmill. The tests performed in this study are not the tests used for certification (Title 42 of the Code of Federal Regulations, Part 84). The tests performed in this study continue until the apparatus are empty to enable comparison of new versus deployed apparatus. The method for obtaining deployed SCSRs for this evaluation was not a random selection from the deployed population of SCSRs. We sought older apparatus with visible environmental impact rather than newer apparatus, and we attempted to sample a wide range of deployment modes. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. This report is the last of 10 report phases begun in 1982. Previous reports describe phases 1 through 9 [Kyriazi et al. 1986; Kyriazi and Shubilla 1992, 1994, 1996, 2000, 2002, 2004, 2006] A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the applicability of the results. The results of these studies suggest that the large majority of SCSRs that pass their inspection criteria can be relied upon to provide a safe level of life support for mine escape purposes. However, the storage and handling in the mining environment seems to have caused performance degradation in some of the apparatus. In this phase, phase 10, we found some CSE SR-100s (93 tested) that exhibited high CO2 levels, stuck-together breathing hoses, starter-O2 failure, breathing hose punctures and tears, high breathing pressures, and loose particulates in the breathing hose. The loose particulates caused coughing in human-subject tests. One MSA Life-Saver 60 (20 tested) in this phase had a stuck-open relief valve. One Ocenco EBA 6.5 (50 tested) had an unattached O2 supply hose. An unexplained phenomenon occurred with two Ocenco M-20s (20 tested): low O2 flow rates preventing their successful use. Almost all of the failures noted involved units that failed their inspection criteria.

Jan 6, 2008

By Allen L. Frank

A portable radon diffusion chamber has been tested with electrical collection of the radon daughter nuclei for enhancement of sensitivity. The detector size was small enough to be worn suspended from the belt. With a battery-supplied high voltage the sensitivity was found to be 1.43 tracks/cm2 per pCi-hr/l of ambient radon at Sot relative humidity. The track densities on the surfaces of the CR-39 plastic nuclear track detectors were found to be non-uniform, making difficult the determination of average densities with high accuracy. The fabrication of electrets for use in the detector was investigated in accordance with published techniques with negative results.

Jan 1, 1983

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By Robert B. Hoekzema

This Bureau of Mines report describes the history, characteristics, distribution, and mineral development potential of 21 lode gold deposits in or near the Chugach National Forest (CNF), AK. It includes findings from a 4-yr (1979 to 1982) mineral evaluation of the CNF conducted by the Bureau and the U.S. Geological Survey (USGS). This evaluation, undertaken to provide the U.S. Forest Service with mineral resource data for use in making decisions on land use, included site-specific mapping and sampling of more than 200-lode gold deposits. The data presented here were compiled from the findings of this 4-yr evaluation and from existing literature. Fourteen of the 21 lode gold deposits described in this report contain a combined identified resource of 117,750 short tons (st) averaging 0.55 oz/st Au and 0.2 oz/st Ag. Two mineralized felsic dikes in the Summit Lake-Palmer Creek area contain a combined identified resource of 18 million st grading 0.02 oz/st Au and 0.16 oz/st Ag. Identified resources were not determined for the remaining five deposits because of a lack of information.

Jan 1, 1987

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A fire detection research program conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) recently demonstrated the advantage of multiple fire sensors for early fire detec¬tion and nuisance alarm discrimination in underground coal mines. As an example, research has shown that an appropriate combination of smoke, CO, and metal oxide semiconductor (MOS) sensors has the capa¬bility to detect a smoldering conveyor belt fire which produces low visibility due to smoke, but CO concentrations too low for an early fire alarm. Such a sensor combina¬tion has the additional advantage of being able to distinguish a nuisance alarm event such as those produced by diesel engines or acetylene torches from mine fire products¬-of-combustion (POC) produced by a real tire. Research has also shown that the problem of hydrogen (H2) gas cross-interference with chemical CO sensors at battery-charging operations in diesel-emissions backgrounds can be resolved with a smoke sensor and a MOS sensor sensitive to NOx associated with diesel emissions. Other underground conditions, such as rock dust, exacerbate the problems with sensors. NIOSH has developed a neural network that takes many of these variables into account as it assesses real-time sensor data to discriminate nuisance alarms.

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a method for determining the helium-3 CHe) content of natural gas and mixtures eontaining 0.5% to 100% helium. The helium is preconcentrated by passing samples through anhydrone, a liquid-nitrogen-cooled chareoal trap, and a titanium absorption trap. The mass spectrometer used to analyze the samples is tuned to 3He at mle ::=; 3.016. Hydrogen deuteride (HD+) interference is minimized by the titanium absorption trap and high instrument resolution. Sample measurements are compared with identically made measurements of a gravimetrically prepared primary standard. The method has a limit of detection of 0.15 ppb with a relative deviation of 13% below the 1~ppb level. The relative deviation is less than 7% for gases eontaining over 100 ppb 3He. The helium isotope ratios of natural gases from the Bureau's Tuck-Trigg Dome Red Cave, the Bush Dome Red Cave, and the Bush Dome Brown Dolomite Formations are distinguishable from one another and from the isotope ratio of crude helium produced from the Panhandle-Hugoton Gasfield.

Jan 1, 1990

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By Robert H. Merrill

This report contains a summary of the various studies made to determine the structural design of the production mine area of the Oil-Shale mine, Rifle, Colo. Prior to this investigation, it had been determined from a study of the geology, the structure of the deposit, and mining costs that the deposit should be mined by open stoping. The problem remained to determine the maximum safe roof span, the optimum extraction ratio, and the size of the pillars. These factors were determined from a study of the geologic structure of the deposit, the physical properties of the oil shale, and the magnitude and distribution of the stress around proposed underground openings. The latter was determined from both theoretical calculations and model studies. Safe roof spans, pillar sizes, pillar contours, and optimum extraction ratios were calculated from elastic theory and the physical properties of the mine rock. Safe roof spans, pillar sizes; and time effects were determined by Wright and Bucky by testing mine models in a centrifuge. The models were made from rock specimens taken from the proposed mine roof and pillars. The results from both studies agreed.

Jan 1, 1954

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part 1 of the report contains the results of the field tests. The studies were made on an oil lease in a so-called "sour district," near Borger, Tex., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field test proved that aluminum lease tanks will withstand corrosion by hydrosulphide, but it as found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore &apos;the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By V. E. Homme

This report describes methods of using sodium for reducing titanic chloride, developed as part of Bureau of Mines activities at Boulder City, Nev., to improve the extractive metallurgy of titanium. Theoretical indications pertaining to the major chemical reactions and possible side reactions of the process are compared with experimental observations. Low-temperature reduction equipment is described, in which titanic chloride was reduced with sodium at temperatures between 97.5° C., the melting point of sodium, and 200° C. Techniques employed in making reductions in ball-mill and high-surface sodium reactors are given.

Jan 1, 1958

By Powell. Alfred R.

"An investigation has been made of the applicability to a variety of coals, other than those from Illinois, of the Powell and Parr method of analysis for the forms of sulphur in coal.A complete study was made of the sulphur in the following coals:- Upper Freeport, Pa.; Pittsburgh seam, Pa.; Pocahontas No. 3, W, Va..; Letcher Co., Ky.; Morgan Co., Tenn.; and Cherokee Co., Kan.The method of analysis gave excellent results when applied to these coals. In the determination of pyrite, the iron-sulphur ratio checked in every case with the theoretical. After the extraction of the pyrite and sulphates, the remaining sulphur was proved to be organic in nature.This work indicated that sulphur exists in coal in three typical forms: - pyrite or marcasite, sulphates, and organic sulphur. A study of the changes which these forms undergo during coking has been made on a variety of coals, and the following five classes of reactions established.First. Complete decomposition of the pyrite and marcasite to ferrous sulphide, pyrrhotite, and hydrogen sulphide. This reaction begins at 300°C., is complete at 600 °C., and generally reaches its maximum between 400 and 500°C."

Mar 1, 1920

By A. C. Fieldner, S. H. Katz

"Introduction.Recent experiments (Fieldner, A.C., Katz, S.H., Kinney, S.P., and Longfellow, E.S., Poisonous gas from carbon tetrachloride fire extinguishers, Jour. Franklin Institute, October, 1920, pp. 543-565), by the Bureau of Mines have shown that carbon tetrachloride extinguisher liquids when applied to fires produce small quantities of irritating and poisonous gases which may be dangerous in very closely confined spaces where conditions are such that the user can not escape without breathing the fumes. The results of the experiments have been confirmed in an independent investigation by the Underwriters Laboratories (Nuckalls, A.H., Corrosive action and products formed when carbon tetrachloride extinguisher liquids are applied to fires, Nat. Fire Protection Assoc. Quarterly, vol. 14, January, 1921, pp. 221-236) who conducted similar experiments for the purpose of determining the corrosive action of these fumes on metals. Both investigations showed that carbon tetrachloride vapor, hydrochloric acid gas, and phosgene were produced in addition to the ordinary products of combustion, such as smoke, carbon monoxide and carbon dioxide. The Bureau of Mines' tests were made by applying a one-quart extinguisher to a wood fire of excelsior in a gas-tight room of 1000 cubic foot capacity. The glass and metal construction of this chamber limited the experimental fire to very small dimensions. It was, therefore, deemed desirable to make a test on a larger scale in the entry of the Bureau's experimental mine in order to similate more nearly the practical use of carbon tetrachloride and other types of extinguishers in mines.Description of extinguishers.Two series of tests were made under identical conditions on different days. Commercial carbon tetrachloride extinguishers were used in the first series of tests and ""foamite firefoam"" extinguishers in the second series of tests."

Jun 1, 1921