Search Documents

By S. P. Mishra, G. R. Chaudhury

The adsorption of Cu2+ ions by Penicillium sp. displayed a dual rate, with an initial faster phase followed by a slower one. The adsorption rate increased with increasing pH due to chemical and biochemical reactions. The Cu-loading capacity of the biomass increased at higher initial Cu2+ concentrations. Above 40 degrees C the adsorption rate decreased which may be due to partial hydrolysis of biopolymers which are essential constituents of the cell wall. Adsorption kinetics followed the Freundlich isotherm and the equilibrium concentration that was calculated on the basis of the isotherm matched the observed value well. A series of theoretical adsorption curves were produced using mathematical correlations between the mass transfer coefficient, the Cu2+ ion concentration at equilibrium and at time t. The correlation between the theoretical and observed adsorption rates for different experimental conditions was good. It was concluded that the results from the study were best explained using a mass-transfer adsorption model

Aug 1, 1995

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By B. S. Terry, C. L. Harris

After measuring the kinetics of Ni reduction from a SiO2-saturated fayalite slag into a Cu-based metallic phase on a laboratory scale, a general model was developed that is capable of simulating mass transfer to and from metal-slag, slag-gas and metal-gas interfaces for multiple species. The model was used to simulate the reactions that occur when Cu and Ni are reduced from fayalite-based slags into a Cu-based metallic phase. Good agreement was achieved between model predictions and experimental data

Aug 1, 1995

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By R. Venugopal, T. C. Rao, N. Suresh

Experiments were carried out using the cyclone to treat coal in the size range -2.0+0 mm. The diameters of the cyclone outlets (vortex finder and spigot) were varied to study their effects on cyclone performance. The cyclone products were deslimed over a screen with an aperture of 0.075 mm. The performance of the separator was studied for washing coarse coal (-2.0+0.075 mm) and fines (-0.075 mm). Performance curves were plotted for the separation of -2.0+0.075 mm coal. The concept of a generalised distribution curve was adopted to predict cyclone performance. A mathematical representation was derived from the generalised distribution curve. The specific gravity of separation for individual size fractions showed a decreasing trend with decreasing particle size down to 0.85 mm, beyond which a reverse trend was noted. It was also found that the fine size fraction (-0.075 mm) does not separate on the basis of size or specific gravity but follows the water distribution

Apr 1, 1995

By B. Denby

sintered ores, to be removed by a pneumatic,

Apr 1, 1995

By R. J. Gochin, M. A. Diaz

A modified Hallimond tube is described which allows the determination of the ultimate recovery R and the flotation rate constant k in a single, continuous experiment. The range of fine particles which can be satisfactorily floated with the modified apparatus can be extended by increasing the length of the bottom part of the tube. Findings suggest that pyrite and arsenopyrite can be separated in alkaline suspension using the so-called F series of collectors. Lime was found to act as a depressant. The collectors operate under pH and dosage control and do not require other depressants. Collectors used in the study were thio-amine (a cationic surfactant) and alkyl propionamide (a non-ionic surfactant)

Apr 1, 1995

By ed. comp., S. H. White, A. J. Naldrett, P. R. Simpson

Peter Simpson's introduction, Tony Naldrett's concluding remarks and discussion by Prof. White of D.M.A. Flight's report of the proceedings are presented from the conference held in Keyworth, UK, in April 1992

Apr 1, 1995

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

horizontal-type classifier prior to charging into a blastfurnace.

Apr 1, 1995

By F. Tailoka, G. Zhao

Pb is an unwanted impurity in Al for which there is no established method of removal. As it interacts strongly with alkali metals, separation was achieved by adding Na or K to molten Al at 953-1 003 K. Direct Na addition led to considerable evaporative loss but in-situ addition by electrochemical titration from a eutectic NaCl-KCl or KCl-BaCl2 mixture was found far more effective, in some cases reducing Pb content below detection levels within 2 h of titration. K appeared more effective than Na at low Pb concentrations but the use of Na was preferred as it is less toxic and explosive. Na removal from Al-Na and Na-Pb alloys was also carried out electrochemically, the use of these two alloys rather than the eutectic salt as a source of Na avoiding liberation of Cl2 at the anode

Apr 1, 1995

By B. E. Burakov, S. D. Lupal, O. A. R. Thalhammer, B. Saini-Eidukat

Electric-pulse disintegration is a mineral separation technique that liberates all mineral grains from any igneous or metamorphic rock irrespective of its lithology or grain-size distribution. The normal mechanical crushing of whole-rock samples is replaced by the rending effect of an explosion, produced by applying an electric current from a high-voltage power source. A voltage greater than the 100 kV necessary for the electrical breakdown of rock samples is achieved by using capacitors charged in parallel, but discharged in series. The sample sits in a water bath and the rapid distribution of electric pulses leads to an explosion which occurs preferentially along grain boundaries of the sample. Individual, undamaged mineral grains can be recovered in their original shape and form regardless of grain size. Examples are given of the liberation and concentration of important accessory minerals from different rock types. The examples show the recovery of diamond from two types of non-kimberlitic host rock in Popigai and Kumdykol in Kazakhstan and platinum group minerals associated with chromitites from the Konjdor intrusion and sulphides from intrusions in the Kola Peninsula in Russia

Apr 1, 1995

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995