Search Documents

By F. L. Wang

The purification process of water-mining carnallite and rough potassium chloride concentrate from Qinghai Salt Lake Industry Group Co. Ltd. are investigated by the preprocessing-reverse flotation technology respectively. The results show that the impurities such as calcium sulfate and sodium chloride can be effectively removed from water-mining carnallite ore and rough potassium chloride concentrate by the new technology, the low-sodium carnallite is obtained and the final potassium chloride product greatly upgraded. The content and the recovery of KCl in the low-sodium carnallite are 25.78% and 97.50%, meanwhile the content of NaCl, CaSO4 in the low-sodium carnallite are 0.56% and 0.24%, and the removal of sodium chloride and calcium sulfate in the low-sodium carnallite are 97.48%, 85.10% respectively. The KCl content and recovery of high quality potassium chloride product are 98.25%, 96.70%, and CaSO4 content is 0.40% with 83.24% calcium sulfate removed in the high quality potassium chloride product.

Jan 1, 2014

By A. Bahrami

Andalusite, silimanite and kyanite are polymorphs of aluminosilicate known as kyanite group. Minerals of this group are used in refractory. Sarband andalusite deposit is located in Markazi province in Iran. Mineralogical studies showed that the main minerals of this sample are andalusite (5%~10 %), mica, quartz and feldspar. Processing of the samples was carried out using two sizes, i.e. +500 µm and -500 µm. In the processing of +500 µm scrabble test was carried out on -4750 +500 µm and -2380 +500 µm. For -500+300 µm shaking table and magnetic separation were applied. For -300 µm fraction, flotation was carried out. The results of this tests showed that the processing of Shazand andalusite was not possible, because silica and iron impurities were diffused inside the andalusite mineral grains.

Jan 1, 2014

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

By Bianca Foggiatto, Marko Hilden, Malcolm Powell

"Since the introduction of the concept of flexible circuits (Powell and Bye, 2009), it has been further developed and refined to the definition of ‚FlexiCircuits leverage ore variability to maximise resource utilisation?. The focus of flexible circuits is to investigate processing options that provide extra capacity through sophistication rather than scale. This requires a combination of smart ore characterisation, economic modelling and innovative processing plant design. Flexible circuit design can reduce energy requirements through gangue rejection or progressive ore upgrade; and increased robustness and controllability by leveraging off ore variation. Each rock type, as characterised through Geometallurgical ore modelling, may be processed more efficiently by individually optimising processing paths. The objective of FlexiCircuits is to transform the processing capability of comminution and concentrator plants - targeting step change in performance through integrating a range of interrelated improvement opportunities. Considerable effort has been applied to developing the modelling and simulations tools required to develop and demonstrate the potential of this concept. This paper presents a practical application as a test case. A realistic application of flexible circuits is provided through a conceptual circuit design of an iron ore processing plant. It is simulated as a multi-component feed with a range of new models in the researcher’s Model Developers’ Kit (MDK) to trial the ability of different circuit designs to respond to variable ore and quantifying the potential of these circuits to transform processing capability of variable ore feed. The outcomes of the simulations are presented and discussed, providing a practical demonstration of the level of modelling and simulation required and the potential of flexible circuit design."

Jan 1, 2014

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By J. J. Lui

Surfactant plays a critical role in many industrial processes such as petroleum, mining, environment and food processing, and daily life. For ionic surfactant systems, adsorption of surfactant at oil-water interface imposes a net charge to the interface. The nature and magnitude of the charges at the oil-water interface depend on charge characteristics of surfactant molecules, concentration of surfactant and solution pH. In our previous study, zeta potential measurement of hexadecane drop-lets in industrial process water was shown to be a simple, yet powerful method for identifying various types of ionic surfactants present in the aqueous system. In this paper, the site-binding model was applied to prediction of zeta potential of oil droplets in aqueous solutions containing a mixture of cationic and anionic surfactant molecules. The total number of interfacial sites for various types of surfactant involved was determined by applying the Gibbs adsorption equation to the measured interfacial tension-surfactant concentration profiles. The distribution of various types of surfactant molecules at the interfaces was evaluated by Langmuir isotherm constants. With the ionization constant of surfactant taken from the literature, the predicted zeta potentials of oil droplets in surfactant solutions from site binding model were shown in a reasonable agreement with the measured zeta potential values.

Jan 1, 2014

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By R. Hejazi, Saghaeian. M., H. Abedini

Continuous vacuum belt filters mainly carry out an important duty in the solid-liquid separation processes such as iron ore concentrate dewatering. However as the particles become finer, the resistance to filtration and dewatering would increase and as the result cake moisture content tends to increase. So in recent decades, using additives in order to improve the filtration performance has been considered by many researchers. In the present study, the effect of several surfactants on the filtration rate and cake moisture content of Chadormalu iron ore concentrate (80% =40 micron) was investigated using a laboratory scale vacuum filter. The results of several tests indicated that a non-ionic surfactant (Lauryl Alcohol Ethoxylated, LAE) has the best performance on reducing the moisture content of the cake and reducing the cake formation time. The optimum dose of LAE was found to be 300 g/ton which reduced the concentrate cake moisture content from 13.76 to 11.28% (wet weight base). Some industrial filtration tests were performed in Chadormalu iron ore concentrate plant to prove the effectiveness of this surfactant. The surfactant is mixed with water and added to the concentrate slurry before distributing on the vacuum belt filter. The industrial and experimental results were almost similar, so that adding about 300 g/ton of LAE would reduce the final cake moisture content from 12.87 to 10.76%.

Jan 1, 2014

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By Markus A. Reuter, Joep Verwoerd, Marc J. A. Pijnenborg, Yongxiang Yang

"Incineration is a proven disposal technology for all waste materials with heat release potentials, and provides high degree of toxic destruction and control for a broad range of hazardous materials. In the Netherlands, all the hazardous wastes are processed at AVR-Chemie located at the Rotterdam harbour, through rotary kiln incinerators. The newly enforced regulations from the European Union with stricter emission levels require a better understanding of the incineration process and improved process control. However, the transport phenomena and combustion processes within the kiln system are very complex and not well understood. In order to get better understanding of the incineration process, research has been carried out to study the fluid flow and combustion behaviour of the incineration system. Computational Fluid-dynamics (CFD) was used to simulate the gas flow and waste combustion process, and temperature measurements of the operating rotary kiln incinerator were conducted to validate the CFD model. This paper will present the latest results from the current research project for simulating gas flow and combustion heat transfer for a wide range of hazardous waste streams.The simulation of the waste incineration process was carried out using a general-purpose CFD code Phoenics. The rotary kiln and the secondary combustion chamber (SCC), with a waste processing capacity of 50,000 ton/y and an energy input of 30 – 40 MW, is translated into a CFD model. The model includes a k-e turbulence model and a global gas-phase combustion model (3-gas or 7-gas combustion model). The 3- gas model (Simple Chemically-Reacting System, SCRS) predicts only the thermal effect of the fuel combustion, and only one global fuel is used, therefore, real chemical species are not taken into account. In the 7-gas combustion model, (an Extended SCRS, ESCRS), different forms of waste fed into the incinerator have been modelled into a mixture of a general hydrocarbon fuel C3H4 and other components such as CO, CO2 and H2O. Thus, all the incoming fuel streams with different compositions and calorific values can be properly converted into separate inlets. The combustion of the waste is assumed to take place only in gas phase in two steps: (1) primary combustion of the main fuel component C3H4 to form CO and H2, (2) secondary combustion of CO and H2O to form CO2 and H2O. The rate of each combustion reaction is assumed to be controlled by turbulent mixing of fuel and oxidant (air or oxygen), i.e. the Eddy-Break-up (EBU) model. The resulted temperature field was validated with temperature measurement data, and the simulated temperature distribution from both 3-gas and 7-gas model have reasonable agreement with the measured data."

Jan 1, 2003

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By B. McFadzean

Thiol collector mixtures are commonly used in the flotation of base metal sulfides and platinum-bearing ores. There are synergistic benefits claimed for these collector mixtures, with mixtures lowering total dosage requirements, improving coarse particle recovery and the rate of flotation. Some of the secondary collectors are known to have frothing effects. Therefore, a previous study aimed to decouple froth and pulp effects and considered only the bubble-particle attachments in the pulp. This was achieved through microflotation experiments, where various ratios of the ethyl and isobutyl chain lengths of xanthates, dithiocarbamates and dithiophosphates were used as collectors. Results from these experiments showed a marked increase in galena recovery using mixtures of xanthate with either dithiophosphate or dithiocarbamate. In the current study, the froth phase was introduced in the form of batch flotation studies to determine whether benefits noted during microflotation experiments would be carried through to a more realistic froth flotation scenario. The findings show that there was no significant difference in the flotation recovery between the best single collectors and mixtures of these collectors. In addition, single collectors that behaved poorly in microflotation experiments showed good flotation performance in the batch flotation experiments. The differences between the microflotation results and the batch flotation results are attributed to differences in particle froth stabilizing properties and/or differences in energy input between the microflotation and batch flotation cells. In addition, galena and pyrite showed marked differences in frothing effects and in their preferences for collector type. Keywords: froth flotation, collector mixtures, sulphide minerals

Sep 1, 2012

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

By Q. Huo

The alumina production might not continue when the sulfur content of bauxite was too high. In order to bring down the sulfur content in bauxite, we studied on the bauxite desulfurization by bacteria screened from the acid mine drainage at mines of high sulfur content. The screened bacteria were domesticated by the high sulfur content bauxite. The experiments of bauxite desulfurization were carried out under the conditions of 5% pulp density, temperature of 30?, rotate speed of 120rpm. Bacterial desulfurization for 30 days, the sulfur content of the bauxite was reduced from 5.73% to 1.55% and the desulfurization percent was 72.9%. The recovery percent of alumina was 94.3%. The study showed that it was feasible to bring down the sulfur content of bauxite by bioleaching and this technique might make full use of the low grade bauxite.

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Peter Ay, Florian Logsch, Satyanarayana Narra

"The traditional lignin separation process from the precipitated suspension creates severe filtration problems by plugging of the filter medium due to the small particle size (20 to 60 µm) of the suspended lignins. The plugging causes further problems in the successive processing of the filter cake. A new lignin separation process has been developed at the Brandenburg University of Technology (BTU) Cottbus as a part of the Research and Development and Demonstration (R & D & D) project "LignoBioFuel". The new developed process separates lignin in the form of granules with diameters ranging from 100 µm to 300 µm. The restrainment of the granule’s size in their successive treatments is expected to result in higher filtration efficiencies and reduction in plugging of filter mediums. To evaluate the filtration efficiency, the filtration resistance of the produced granules as well as the conventional suspensions has been investigated. The results show that there is a 60 to 80 % filtration efficiency increase and around 60 % reduction in plugging of filter mediums with the lignin granules in comparison to the conventional suspensions. Furthermore the successive processing of lignin granules was easier due to their porous structures removing the impurities such as adherent acids and salts. The purity of the separated lignin was measured with their sulphur (reduced from 7 % to 2.7 %) and ash (reduced from 46 % to 0.5 %) contents. The newly developed process has displayed better results in comparison to that of the conventional process. The new process displays high potentials in optimizing and improving the present state of the art treatments and is promising several ecological, economical and environmental improvements."

Jan 1, 2014