Search Documents

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By K. E. Waters, J. E. Nesset, F. Rosenblum, R. Langlois, J. A. Finch

"Some sulphide mineral mixtures when exposed to air and a warm and humid environment can exhibit a self-generating temperature rise, referred to as self-heating or spontaneous heating. The observed self-heating derives from the oxidation reactions of the active sulphides. In previous publications by the authors, it was proposed that the self-heating of sulphides proceed in three distinct stages; namely, Stage A, Stage B and Stage C. In Stage A (<100OC) the sulphides, in the presence of moisture are oxidized, generating heat through a series of sequential reactions and forming elemental sulphur as one of the products. In Stage B (>100OC) the elemental sulphur produced in Stage A is further oxidized to generate additional heat and SO2. Stage C (>~380OC), sometimes referred to as thermal runaway or roasting, is not addressed in this paper. This communication focuses on the type and role of elemental sulphur found in Stages A and B, and the sequence of reactions that is occurring in Stage A. The sequence is divided into two phases, the first based on galvanic interaction between the sulphide minerals that generates an acidic environment but little heat, and the second involving the production of H2S which rapidly oxidizes to produce heat and elemental sulphur. To date, data suggest that the primary oxidation product formed in Stage A is the stable orthorhombic a-S8 form of elemental sulphur. Above 96OC the a-S8 transforms to a monoclinic ß-S8 structure which is less stable and will readily oxidize to generate heat and SO2. Above 159OC a proportion of the ß-S8 sulphur will transition to a polymeric Sµ form of sulphur which can readily volatilize. INTRODUCTION Some particulate and granular materials, when exposed to appropriate atmospheric and physical conditions, can exhibit a self-induced temperature rise resulting from accumulated heat due to internal exothermic oxidation reactions. This phenomenon is commonly referred to as self-heating or spontaneous heating. Under favorable physical and environmental conditions, these reactions can elevate the temperature of a given material from ambient to the point of auto-ignition. Self-heating behaviour should not be equated to pyrophoric behaviour which describes a group of materials (e.g. certain finely powdered metals) that will ignite spontaneously in air below 55OC. There are numerous materials such as coals, hay, forestry wood products, food products to name a few that can exhibit self-heating behaviour. This publication continues the focus of the authors on the self-heating of sulphide mineral mixtures. Many of the metals of commercial use found in nature are in the form of these sulphides which must be mined, crushed, ground and concentrated prior to smelting or hydrometallurgical processing in order to produce primary metal. The issues of sulphide self-heating therefore pertain to the mining and processing of metals."

Jan 1, 2018

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By G. J. Mei

Separation of hematite and iron-containing silicate gangue - aegirine by Flotation using fatty acid collector and (NH4)2SiF6 depressant was investigated in this paper. The flotation tests with single minerals show Ammonium hexafluorosilicate (AHFS) is a selective depressant for aegirine in hematite flotation in weakly acidic medium, which can strongly reduce the flotation recovery of aegirine in the pH range of 4~5 while has no evident effect on the flotation of hematite. The results of flotation tests with actual ores show the separation of hematite from aegirine gangue by forth flotation was possible, and good selectivity was achieved. Chemisorptions were observed on aegirine mineral surface treated by AHFS solution by using SEM and IR spectrum measurements. On the basis of coordination chemistry, a comprehensive mechanism, which reasonably explains the selective depression of AHFS for iron-containing silicate, is also proposed.

Jan 1, 2014

Results of the study of chloride ion concentration effect to osmium-187 sorption from wastewater of copper smelter with use of foreign anionites of different basicity and structure are presented in the work. It was found that the increase of chloride ion concentration in the wastewater helps to increase recovery of osmium using anionites regardless of their nature. The ways to intensify the process are proposed. The method for osmium elution from the anionites with potassium iodate solution was developed. It was shown that the method lets to recover up to 99% of osmium from the anionites. Recommendations for selection of eluents for better recovery of osmium from the anionites were elaborated. Keywords: wastewater, osmium, anionite, sorption, chloride ions, eluent, recovery

Sep 1, 2012

By Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Istanbul Technical University, Mustafa Tarkan

"Zeolites are naturally occurring as hydrated aluminosilicate minerals. They belong to the class of minerals known as “tectosilicates” and are related to the common minerals feldspar and quartz. Seven natural zeolites that occur in large, commercially exploitable deposits, are: clinoptilolite, chabazite, mordenite, phillipsite, erionite, analcite, and ferrierite. Among them, clinoptilolite is the most abundant one and is not the best known, but is one of the more useful natural zeolite. Clinoptilolite [(Na3K3) (Al6Si30O72) 24 H2O] is very closely related to heulandite and is currently being considered for disuse it self as it may just be a variety of heulandite. It differs from heulandite significantly only in its enrichment in potassium and slightly more silica and it is argued that a separate mineral is not needed.There are large zeolite deposits in western part of Turkey. The sample used in this study was taken from the Gördes region of these deposits. Screen, chemical, XRD and mineralogical analyses were used to determine properties of the natural zeolite sample used in this work.According to the size distribution of the sample, it is found that the zeolite sample used in this study is below 1 mm in size and almost 80% of it is below 0.5 mm. X-Ray Diffraction (XRD) and mineralogical analyses show that the natural zeolite is found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. XRD analysis also shows that the sample contains approximately 58-60% clinoptilolite, 5% quartz, 5% feldspar, 10% smectite, 5- 10% illite and mica and remaining volcanic tuffs. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals."

Jan 1, 2003

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By M. Y. Zhou

The paper elaborates on the significance of producing ultra-low-moisture ore concentrate, the operating principle and technical features of thermocompression- filtration process, the kinetics involved in the dewatering process, and the technological process system and equipment used. It is pointed out that it is possible to reduce the moisture of fine ore concentrate to a minimum. By way of example, the case of the treatment of flotation molybdenum (Mo) using the thermocompression- filtration process is cited.

Jan 1, 2014

By S. K. Chaurasiya

o meet the ever increasing demand of iron oxide feed stock for rapidly growing domestic steel industries and to effectively manage the depleting reserve of high grade lumpy iron ore, Pelletization of iron ore fines/slimes are expected to play a dominant role in the near future. Use of pellets will also enable the blast furnace operator to achieve higher levels of productivity with lowering of operating cost. The effective utilization of Iron Ore Slimes is important not only from the point of view of optimum utilization of Iron values in the mined ore but also for preventing environmental pollution. A significant amount of slime is being accumulated at the tailing dam of one of the iron ore mines and with the present scale of operation the tailing dam will be filled in another 10 years. Hence to increase the life of tailing dam and for better utilization of the iron values a study has been carried out for the suitability of pellet manufacturing with slimes and fines at our laboratory. The pelletization studies are aimed for optimization of various parameters for production of Blast furnace/ DR grade pellets from beneficiated slimes and Fines. This paper attempts to describe the production of blast furnace grade pellets from beneficiated slime and fines and its characterizations.

Sep 1, 2012

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By A. Kurkov

Flotation process is based on the formation of primary collector-based supramolecular associates at the mineral surface and within the pulp. Supra molecular chemistry allows studying within a common framework, all kinds of molecular associates, from dimers to large assemblies, resulting from spontaneous association of a large number of interacting components of the flotation system, where the collective action of non covalent bonds can have an important role. Self-organization of supra molecular assemblies in the flotation process can be controlled by modifying the chemical structure of the collector, the nature and arrangement of functional group in it, by introducing secondary agents (SA) into the process, to adjust the interaction between the collector and the surface and to control the hydrophobicity of the adsorption bed. This offers broad opportunities to build supramolecular assemblies to improve the efficiency of flotation. Besides, the more complex is the system, the weaker are the interactions, that determine its behavior. This powerful factor still is not employed deliberately to control the flotation process. Organophosphorus compounds (OPC) - dialkyl phosphoric acids whose radicals contain ethoxylated groups ? are considered as nanocompounds, that can be used in building supramolecular assemblies. The presence in an OPC molecule of functional groups (P=O, P (O) O-, P (O) OH), ethoxylated groups, and aromatic rings is the basis for the formation of stable supramolecular associates. Gross formula: C54H94KO16P. Molecular weight is 1069.39. Phosphoryl anion has a regular tetrahedral structure with the angle of 109.5°. Lengths of -P-O- bonds in a PN molecule are 1.7345Å; length of the hydrocarbonic radical C42-C72 = 33.942Å. In an alkaline environment, PN is in the form of the anion, in an acidic environment ? in the form of the polycation due to protonation of the oxygen in the EO group. Chem Office software suite was used to generate three-dimensional images of an OPC molecule in acidic and alkaline environments, to reveal the OPC geometry (bond lengths, valence angles, aliphatic radical length), to identify the collector&apos;s binding sites with the mineral surface, to find the most stable and energy-efficient molecular conformations of an OPC molecule and its complexes with minerals under various conditions. Mechanisms of interaction between OPCs and the mineral surfaces are different. In ores whose minerals are dominated by ionic bonds (fluorite), the interaction mainly involves the anionic form of the collector; in ores, whose minerals are dominated by covalent bonds - the oxygen of the phosphoryl group (donor-acceptor interaction) and the oxygen of the ethoxylated groups. This difference is responsible for the formation of spatial associates with different surface layer structures. Introduction of supramolecular chemistry concepts into the analysis of flotation phenomena and mechanisms can become an effective tool for better understanding the flotation process and offers new means of consistently improving its effectiveness.

Sep 1, 2012

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018

By Xiqing Wu, Tao Yue

"Magnetic seeding co-agglomeration, i.e. adding magnetic seeds, organic depressant (such as the starch), and pre-magnetization for co-agglomeration, was applied in the reverse flotation for hematite ore slimes. Samples of the hematite ore slimes and the pure hematite fines were investigated by the co-agglomeration, respectively. Flotation tests suggest that the depressing effect of starch in the flotation was further enhanced with the addition of magnetic seeds and the pre-magnetization. Following the laser size analysis and flotation tests, TOC adsorption analysis, VSM, surface charge measurement, AFM, FTIR study, and SEM imaging have been utilized to understand the depressing mechanism. Based on the results it was demonstrated that with the addition of magnetic seeds and the low field pre-magnetization, the adsorption of starch onto hematite minerals was strengthened through the magnetic seeding co-agglomeration. The co-agglomeration improved the flotation performance by introducing the magnetic interactions and acting the bridging adsorption of starch between fine hematite and magnetic seeds in a suspension, and then resulting in an intensified coverage of the starch onto hematite particles and positive action in the coagglomeration under the pre-magnetization.INTRODUCTIONFlotation is undoubtedly the most important and versatile mineral processing technique, and both its use and application are continually being expanded to treat greater tonnages and to cover new area. However, its influence was limited to a relatively narrow particle size range of 5–300 µm (Wills and Napier-Munn, 2006). The main reason behind this limitation lies in that fine particles have high specific surface area, so need relatively high dosage of reagents (collectors or depressants), and exhibit poor flotation performance while intermediate or properly-sized particles produce high flotation kinetics and need low consumption of reagents. In order to increase the recovery of fine particles, quite a few of flotation techniques have been investigated. Most of them are based on particle aggregation, namely, by enlarging the apparent particle size, such as carrier flotation (Valderrama and Rubio, 1998; Zhu et al., 2009), shear flocculation (Duzyola and Ozkan, 2010; Yin et al., 2011), selective polymer flocculation (Rubio et al., 2007; Song et al., 2012; Ng et al., 2015), oil agglomeration (Laskowski and Lopez- Vladivieso, 2004; Forbes, 2011), temperature responsive polymer flocculation flotation (Forbes et al, 2011), and etc. However, these techniques above-mentioned are mainly studied for the direct flotation of fine minerals, and most of these techniques have not found applications for iron ore slimes especially recovered by the reverse cationic or anionic flotation."

Jan 1, 2018

By Jury P. Nazarov

"At present the traditional study of crystal lattices of nmerials in a topic “flota tion mineralogy ” is used up. The present investigation is development of the a sclsical approaches to t he analy sis of ideal crystal lattices and f ormation on the basic obtained results of consultation, having practical chara cter.The strategy of develop ment floatation reagents i s offered, which basic pr inciple – complementary assembling m olecules forming surface co mpounds so thatth e steric charact eristic of the “visitor "" (of a polar gro up of molecule SAS) corresponded to the st er ic requirements of the ""o wner"" (elementary cell of a mineral), or coincided inter molecular cavities). In itsh case process of for mation of surface com pounds ca n be considered(a first approximation) as a realization of a principle of the design er "" LEGO "".The approach, which basic idea consi deration actioonf reactant ions and ions of ele mentary cell as three-di mensional objects is developed. And at suchp paroach the laws of a ster eometry - laws describin g spatial effect s are applicable. Thus it is possible toconsider a miner al surface as a mat r ix - basis for formation of the requirem ents to polar group of a molleec cuollector, and or (it is possible) depressant. As a whole approach represents a generalized principle double com plementation, enveloping both power, and geometric asp ects (concept ""lock "" and “key "" - spatial conform ity. Figure 7 (left). Fragment of a crystal lat tice of ap atite. Oleic acid ions interact on ly with th e calcium cations locate d on a long axi s of an elementary c ell. Magenta colour represe nts the calciu m cations, which are n ot particip atin g in interactio n, as th e degree of screening by ions neighbours exceeds 1.Figure 2. (right)The illustration of space complementary. “Afterbuilding” an elementary cell of apatite (radical PO4) related molecules of the visitor – alkyl phosphate (polar group PO4). Cations of calcium are not shown."

Jan 1, 2003

By Brian Hart, Rong Fan, Roger Smart, Andrea Gerson, Ning Xu

A complete strategy has been developed for identification of the reasons for losses in recovery and/or grade, due to changes or complications in mineralogy and in mineral surface conditioning, and their subsequent correction. The sequence of methods starts with comparison of mineral phases between QEMSCAN/MLA (compositional) and Rietveld XRD (crystalline diffraction) with bulk assay reconciliation. This methodology has recently led to identification of unrecognised amorphous content (12-40 wt.%), previously attributed to crystalline phases, in the fine fraction (<35 µm) of some problematic flotation feeds. Attached amorphous silica, talc- and chlorite-like fines have direct influence on the hydrophobic/ hydrophilic ratio on value mineral surfaces adversely affecting flotation. SEM/EDS is used in the backscattered imaging mode to determine possible problems with liberation (e.g. remnant local locking), not detected in standard liberation analysis, resulting in gangue flotation. EDTA extraction is used to assess bulk feed pre-oxidation and sequential oxidation product loading through the circuit. Changes in circuit solutions are assayed with speciation modelling of precipitates and potentially adsorbing species. ToF-SIMS with principal component analysis is then used to correlate surface species with specific minerals and can be used to assess the effectiveness of specific reagents particularly collectors. This approach identifies unwanted activating species and interference with value surfaces by adsorbed hydrophilic ions, precipitates and fine particles. When the interference or ineffective reagents are specifically identified, remedial action can be targeted. This method has identified residual talc-like layers (<10 nm thick) inducing gangue flotation of pyroxene and chromite in PGM flotation. Recent case studies of application of the full methodology to losses of molybdenite at KUCC and to sphalerite activation in the Cu/Pb circuit at Brunswick Mines with remedial action are discussed.

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By P. M. Solozhenkin, V. N. Kovalev

Russia is a global antimony market leader. The three major antimony production provinces are Sakha Republic (Yakutia), Krasnoyarsk Territory and Trans-Baikal Territory. Russia’s largest antimony resources are Zhipkozhinsky and Solonechensky deposits in Sakha Republic (Yakutia) and Olimpiadinskoe deposit in Krasnoyarsk Territory. This work demonstrates the efficiency of computer programs and chemical technology aimed at the study of the behavior of collectors used in the processes of flotation of antimony, arsenic and Au (I – III) minerals. The most promising collectors for the flotation of ores containing antimony and gold on the basis of P(V) and compounds with S, O and N atoms were chosen. The mechanisms of interaction with the mixtures of two or three components of collectors were studied. High recovery of antimony and gold was reached in the processing of Au-Sb ores of Sarulah and Sentachan deposits in Sakha (Yakutia). X-ray radiometric methods of separation of antimony ores of Trans-Baikal Territory deposits were proposed. In order to choose the most cost-effective solvents for hydrometallurgical processing of Sb, Au-containing concentrates the method based on clusters formation between transition solvents and antimony minerals was suggested. The nature of Au losses was theoretically revealed in the sulfide-alkaline process. On the base of computer simulation, the formation of various complexes of (KAu) types was developed, for example, hydrosulphidic gold, thiosulfates of gold - Na3AuS4O6, antimony and arsenic gold, trithiostibate (III) and trythioarsenate (III) KAu were produced. The practice of processing of goldantimony concentrates to produce high-quality antimony trioxide and antimony-gold containing alloy (AGCA) regarding the special conditions of the Far North region, were analyzed. The affinage of AGCA was recommended. Creative project development of antimony industry in Russia in order to produce antimony compounds and pigments, including pyriform compounds and flame retardants (antipyrenes) is discussed.

Jan 1, 2018