Search Documents

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By Xiaoxu Sun, Jianchao Yao, Jiancheng He, Shijie Lu, Hongxi Zhou

"With the trend of increasingly more mineral resources turning low-grade and refractory, more and more new ore bodies being developed worldwide are more finely grained, which drives the rapidly development and application of techniques related to tower mills (vertical spiral stirred mills). However, the lacking in fundamentals of fine grinding, as well as standard procedures for equipment selection and scale up, seriously restraint high efficient application of tower mills. Taking grinding media motion characteristic and grinding intensity as a breakthrough point, this paper studies mechanisms behind how critical parameters affect grinding efficiency of tower mill, including ratio of screw pitch and diameter, agitator rotation speed, grinding media size. Several sets of orthogonal test are conducted on the quartz ore using the grinding system of KLM-3 tower mill. All the tests are under the same character of feeding mineral and undergo the consistent sampling for at least 60min grinding time. The input power is measured by a torque measurement system and the grinding products are analyzed by the laser particle size analyzer. The test results show the influence of parameters on grinding efficiency. Among the three important parameters, the effect of grinding media diameter is the biggest, followed by the agitator tip speed, and finally the ratio of screw pitch and diameter. For the different particle size of grinding products, the best combination of grinding parameters is different, with the mineral size becoming finer, the ratio of screw pitch and diameter become smaller, the diameter of grinding media become smaller, while the agitator tip speed does not change too much. The conclusions of the study help us to improve the grinding efficiency of the tower mill, to assist in the selection and optimization of working parameters, establish new scale up method on the basis of grinding model and eventually provide theoretical basis of rational selections of structural and media physical parameters within tower mill."

Jan 1, 2018

By C. B. Yu

The ore comprise of chalcopyrite, valleriite, pyrite, pyrrhotite and so on. Serpentine and talc are chief gangues. Copper phase of the tail shows that mostly valleriite be losed in tail, 70% mineral of copper is valleriite in tail, so severity reduce the recovery of copper. The traditional flow-sheet in acidity mine pulp to flotat the valleriite, but copper-sulphur separated in high alkaline pulp, so the valleriite be losed else. Explores the characters of the valleriite?s surface, studys on the flow-sheet of flotat valleriite and copper-sulphur separated. In neutral mine pulp, adopt of cationic collector to flotat valleriite, adopt of hyposulphite to depressant pyrite in low alkaline pulp can advance the recovery of copper to 5.06%.

Jan 1, 2014

By Sudhir Srivastava

India hosts a wide range of globally significant mineral resources, including four fuel minerals; 11 metallic minerals; 22 minor minerals and 52 non-metallic minerals. The country ranks among world?s top five nations for its commodity reserves of coal and iron ore. Interestingly, only small part of country&apos;s landmass has been explored that provides opportunity for future substantial mineral discoveries. India plans to double infrastructure investments to US$ 1trillion. Despite the challenges in infrastructure project implementation, mining sector remains a key driver of demand growth for commodities in the years to come with a good prospect to grow in future.

Sep 1, 2012

By Z. H. Wang

The internal parameters of ball mill are very important in the grinding process and have significant impact on the grinding results. Accurate measurement of the internal parameters of ball mill is crucial and indispensable for optimization and control of grinding process. In this paper, a novel tri-sensor measurement method was used to measure the external signals (i.e., bearing pressure, sound intensity and power consumption) of ball mill. Mathematical models, which link the external signals of ball mill with its internal parameters, were established to predict the internal parameters of ball mill. Experimental results showed that the mathematical models could directly predict the internal parameters of ball mill once the external signals were obtained. The tri-sensor measurement method and the mathematical models proposed in this paper provided a new way and solid basis for optimization and control of ball milling.

Jan 1, 2014

By F. J. Sotiuo

Variability of the quality of phosphate ore feed to the flotation plant has been of great concern for the industry. This variability sometimes resulted in 10% to 50% decrease of P2O5 recovery, a reduction of P2O5 concentrate grade and/or both due to depression of the system. For this investigation, samples of refractory ore and easy-to-float ore were obtained from the same mining area in Central Florida; and then submitted to bench flotation tests using fatty acids (FA). To understand the cause of difference in flotation behavior of these apparently similar ores (grade, mineralogy, and physical appearance), bulk and surface characterization studies were conducted. Based on the results of characterization studies and bench flotation tests on both refractory and easy-to-float samples, it was possible to determine FA surface coverage. It was found that the surface coverage for the refractory ore was between 6.9% and 9.8%, corresponding to 0% and 80% recovery, respectively; whereas the easy-to-float ore showed surface coverage of 17.2% (89% recovery) to 24.6% (98% recovery). Since size analysis, surface area and pore size measurements showed small differences, it was thought that the surface coverage differences could be caused by the ad-sorption of natural compounds onto the phosphate ore surfaces, depressing the system. SEM, EDS, and Leaching and Solvent Extraction (LSX) studies were performed on the phosphate ores to demonstrate the proposed mechanism. This paper summarized our characterization studies, flotation results, and findings. The study showed that the new identified compounds were responsible for the flotation behaviors of the Florida refractory phosphate ores.

Jan 1, 2014

By K. Saberyan

In this study, solvent extraction of zirconium by using triphenylphosphine oxide as extractant has been investigated. The results showed that extraction of zirconium by triphenylphosphine oxides in nitric acid and hydrochloric acid media were negligible. Extraction of zirconium in acetic acid media with concentration of 0.01~0.2 M has been studied and the results showed that the maximum percent of zirconium extraction was 40% in acid acetic with concentration of 0.01 M. By addition complexing agents such as potassium thiocyanate with the concentration of 0.01~0.2 M zirconium extraction increased up to 86% in 0.2 M potassium thiocyanate. By addition of sodium salicylate with concentration of 0.01 M and in pH=2.5, the maximum extraction of 96% was achieved. The striping of zirconium from organic phase can be carried out by 0.5 M solution of sulfuric acid.

Jan 1, 2014

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By Weiran Zuo, Emmy Manlapig, Fengnian Shi

The effect of metalliferous grains on electrical comminution efficiency was investigated by comparative experiments using natural rocks and synthetic samples. The result indicated that the existence of metalliferous grains affects the breakage probability and product size distribution of electrical comminution. On average, metalliferous grains increased the breakage probability of particle in the first pulse discharge by 55% and generated finer product at the coarse end. As a result, particles with metalliferous grains exhibited higher energy efficiency than that without metalliferous grain in electrical comminution. A positive linear relation between product fineness and specific energy in electrical comminution was observed. With the assistance of numerical simulation on the electrical field distribution of ore particle, the role of metalliferous grains in electrical comminution is confirmed and the mechanism of metalliferous grains effect is elucidated. Understanding of the effect of metalliferous grains on electrical comminution is important to evaluate the feasibility of applying electrical comminution to ores with different mineral composition, and to understand the breakage behavior in electrical comminution.

Jan 1, 2014

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014

By Polezhaev S. Yu, I. V. Ukraintsev, Boduen A. Ya, Saburbayeva L. Yu

"Comparison studies of different technologies are performed when selecting optimum option for gold ore and concentrate processing. Methods of ultrafine grinding, oxidizing roasting, bacterial leaching and pressure oxidation are used to extract gold from refractory ores and concentrates. Refractory gold flotation concentrate produced from pyrite-arsenopyrite ores of Bestobe deposit is a case study in this paper. The results of the experimental tests of the direct leaching of flotation concentrate and pre-oxidation products using different methods (oxidizing roasting cinder, pressure oxidation and bacterial leaching cakes) are the following: - cyanidation of original flotation concentrate provides recovery of Au at 46.6 %; - oxidizing roasting increases gold recovery from 46.6 % to 85 %; - BIOX increases gold recovery up to 86 %; - preliminary pressure oxidation of flotation concentrate ensures steadily high Au extraction in the follow-up cyanidation at 94.9-96.5 %. Pressure oxidation and bio-oxidation has changed dramatically the strategy of refractory gold ore processing. These solutions provided for development of ore deposits that considered earlier non-commercial. However, refractory ore processing has a complex character in terms of developing process flowsheet and requires large amount of studies to be performed for each new project. Gold extraction is the basic but not the only criteria to technology selection for gold ore and concentrate processing. Opex and capex, ore reserves, regional geography, developed infrastructure and skill personnel should be considered. Process studies and feasibility study of the developed technology shall be provided for each specific gold ore deposit. INTRODUCTION Due to changes in available feedstock and depletion of easy-to-process ores, refractory ores containing finely disseminated gold and silver in sulphides (primarily, in pyrites and arsenopyrites) are more and more involved into processing. Experts say that such ores amount above 40 % of the world’s gold reserves. Conventional technologies of gold extraction from refractory ores include flotation, roasting and cinder cyanidation (Fraser etal., 1991). However, today’s best available practice for refractory gold ore processing are bacterial (BIOX) and pressure (POX) oxidation."

Jan 1, 2018

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By Carlos Rabanal, Levi Guzmán

"The concern regarding grinding media consumption rates is as old as the invention of the tumbling mill. Over the years many materials and grinding media shapes have been tested. Through all this, steel grinding balls have proved to be the most effective media for comminution in tumbling mills. There have been several approaches to be able to the wear of the ball charge in any given mill, all of them based on limited empirical evidence. The mining industry still utilizes the Bond Abrasion test that was developed in the 1960´s. As shown later in this publication, this approach shows error greater than 60%. More recently, in 2007, Radziszewski from Mc Gill University has proposed a different total grinding media wear model; this model is based on decoupling the effects of the abrasion, corrosion and impact wear mechanisms. Also in 2007, Benavente, at the time with Moly-Cop Peru, presented an empirical model relating both ore properties and operational conditions that would affect the wear performance of the grinding media. For the database referred in this article, Benavente’s model shows an average error of ± 12% which represents a higher degree of improvement in comparison with previous approaches. The current paper presents recent research conducted by Moly-Cop Peru to further improve the capability of the empirical model originally developed by Benavente to estimate grinding media wear rates. The work performed included extensive determinations of the Bond Abrasion Index for different types of ores, collected at industrial grinding applications where the corresponding operational information was made available. The results of the research enabled us to build a more robust and confident model for estimating the grinding media wear rate. The average error of this new model is in the order of ± 9% which is a significant improvement over the models previously described."

Jan 1, 2014

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018

By Seungwoo Park, Gaurav Soni, Roe-Hoan Yoon, Hyunsun Do, Kaiwu Huang

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing bubble size to increase, bubble surface area to decrease, and hence casing less hydrophobic particles to drop off to the pulp phase below. Thus, bubble coarsening provides an important mechanism by which product grades are increased. On the other hand, excessive bubble coarsening results in low recoveries. In the present work, a model describing the process of bubbles becoming coarser in a foam as they rise to the top by deriving a mathematical relation between the Plateau border area, which controls film drainage rate, and the lamella film thickness, which controls bubble-coalescence rate. The model has been derived by assuming that liquid drainage rate increases due to slip at the air/water interface, and that the critical rupture thickness is determined by the capillary waves created by thermal motion. The model developed in the present work can predict the bubble size ratio between the top and bottom of a foam as functions of aeration rate, foam height, and surface tension (frother dosage). The model predictions are in good agreement with the changes in bubble sizes measured using a high-speed camera.

Jan 1, 2014

By C. B. Wu

This paper presents an analysis of comminution behavior of using cast iron segment (CIS) as fine grinding media with comparison to conventional steel ball. Grinding experiments utilize just one-size medium and mixed size media in laboratory were carried out and its efficiency is expected to be improved. The results show that no matter whether one-size medium or mixed size media employed, grinding efficiency of CIS media can be considerably equal to that of steel ball, on the other hand, grinding product by two kinds of media can conform to Robin-Rammler?s size characteristic curve and distribute in function of . )exp(100nbxy-= Comparing with steel ball, the milling capacity with CIS media could be increased up to about 8.6 percent, overcomminution decreased 3.96 in percentage and qualified size increased 3.98 in percentage in case of grinding fineness retained. At the same time, due to the improvement of grinding product size characteristic and its metal distribution characteristic, the grade and recovery of easy to separation size increased 0.24 in percentage and 6.47 in percentage respectively. Based on these results, the CIS media can be employed as novel fine medium for grinding process substituting for steel ball.

Jan 1, 2014

By Jochen Petersen, Harro von Blottnitz

"The landfill disposal of slags is common practice in the metallurgical industry. Chromium may be a minor constituent in many cases. It is present mostly in the form of chromites, which are considered environmentally benign and hence safe for disposal. Wastewaters from metal finishing operations are most commonly treated by reduction and precipitation of dissolved metals, including chromium, by lime addition, and subsequent landfill disposal of the resulting sludge. The metals contained in such sludges are mostly in the form of hydroxides, and as such considered environmentally stable.Thermodynamically, trivalent chromium, which is the predominant form in these waste materials, can be oxidised to the hexavalent form by atmospheric oxygen. Detailed research work on both slags and sludges has shown that a gradual emergence of hexavalent chromium can indeed be observed. The mechanism is governed by close physical contact between chromium oxide (or hydroxide) phases on the one side and calcium oxide (or hydroxide), which is present as flux in slags and residual lime in sludges, on the other. If oxygen can migrate to the points of contact, gradual formation of calcium chromate ensues.Hexavalent chromium is associated with high environmental toxicity, and hence undesirable in landfilled materials. Moisture migrating through landfill deposits can mobilise the highly soluble chromates and thus potentially transport them into natural waterways. Such gradual release from stainless steel and ferrochromium slag deposits has been demonstrated in a column experiment."

Jan 1, 2003

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By Sergey S. Gudkov

In the current climate of changing the approach to mining and treatment of mineral resources, processing technologies are being developed that require little maintenance and are economically as well as ecologically sustainable. This may also involve the development of entirely new ways of ore processing. One promising approach is to use bioleaching for the pretreatment of gold refractory ores to cyanidation. Capital costs for vat bioleaching of concentrates and ores are very high and cannot be applied for small or medium-size deposits. IRGIREDMET JSC carried out bio heap leaching test work on refractory ore samples from three Russian deposits. Following this biological treatment a combination of flotation, vat bioleaching, and cyanidation are used to recover gold. After heap bioleaching, gold recovery was 75-80 per cent. It was found that efficiency of heap bioleaching process depends on ore feed size. High duration of this process is another feature and it lasts for about a year. This process can be also used for carbonates in the combination with other process during which acid generation occurs. The results of our studies have shown that this technology is amenable for refractory gold ores. Its introduction allows an increase gold recovery and to solve a number of environmental problems. Keywords: heap biooxidaton, the refractory of the ores, the degree of oxidation, arsenopyrite, pyrite, CIL

Sep 1, 2012