Search Documents

By Al Cropp, Julie Hunt, Will Goodall, Ron Berry, Dee Bradshaw

Geometallurgy aids the understanding of ore body variability but has the most value if the data is easily available along the entire mining value chain. This requires cross-discipline communication and collaboration across traditional silos, and an organizational culture that encourages that to flourish. Data that are collected by the numerous groups (i.e. mining, geology, milling, processing, refining, smelting, marketing, environmental etc.) involved in the mining process may have relevance to other stakeholders; mineralogical and textural data for example has value to all these groups. Data required for modeling comminution or identifying acid potential from waste rock may already exist, however it needs to be made available to all the relevant stakeholders in the right format at the right time. As part of the GeM (AMIRA P843 & P843A) project the opportunity has been taken during the sponsor meetings, short courses, case studies etc. to ask the question: ‚What information do you want from further up the chain?? For example, to metallurgists ‚What information would you like from the geology group before the ore enters the mill?? The geology group may already have information important to mineral processing but not know it is of interest. This could, for example, be in the form of a geometallurgical drill core log that contains quantitative measured values. This paper focuses on the interaction between the mining, geology, mineral processing and environmental groups, using ore properties resulting from geological alteration to identify potential impacts throughout the mining process and discusses how a cross discipline approach can benefit all.

Jan 1, 2014

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or EPD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to – 2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to –2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: –2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals."

Jan 1, 2003

By M. Evertsson, K. Bhadani, E. Hulthén, M. Bengtsson

"Modelling and simulations for mineral processing plants have been successful in replicating and predicting predefined scenarios of an operating plant. However, there is a need to explore and increase the potential of such simulations to make them attractive for users. One of the tools to increase the attractiveness of the simulations is through applying optimization schemes. Optimization schemes, applied on mineral processing simulations, can identify non-intuitive solutions for a given problem. The problem definition itself is subjective in nature and is dependent on the purpose of the operating plant. The scope of this paper is to demonstrate two optimization schemes: Multi-Objective Optimization (MOO) using a Genetic Algorithm (GA) and Multi-Disciplinary Optimization (MDO) using an Individual Discipline Feasible (IDF) approach. A two stage coarse comminution plant is used as a case plant to demonstrate the applicability of the two optimization schemes. The two schemes are compared based on the problem formulations, types of result and computation time. Results show that the two optimization schemes are suitable in generating solutions to a defined problem and both schemes can be used together to produce complementary results. INTRODUCTION The comminution process for a mineral processing plant consists of multiple crushing and classification stages and aims to produce fine material to liberate ore from the minerals. The modelling and simulation of such processes are well established using static process models (King, 2001; Napier-Munn et al., 1996). A recent development in the dynamic modelling for such processes has shown further increase in fidelity compared to the static process models (Asbjörnsson, 2015). The developed simulations can be utilized to design, operate and control mineral processing plants based on the requirements of users (Bhadani et al., 2017). Typically, the requirements in the operation of the comminution process are conflicting in nature, as for instance, reduction of power draw by process units, maximization of production of fine materials, and increasing utilization of the process units. These conflicting requirements leads to a Multi-Objective Optimization (MOO) problem to operate a mineral processing plant. The MOO problems are normally referred to as non-linear problems and its fundamental understanding with respect to process behaviour is difficult to achieve."

Jan 1, 2018

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By Luís Marcelo Tavares, Juliana Segura

Comminution is one of the most energy consuming stages in a mineral processing plant. This consumption is not only related to the power supplied to equipment, but also to the indirect or embodied energy, mainly associated to materials that are worn during operation, including grinding media and liners. Until recently, preparation of iron ores in Brazil did not use comminution intensively, given that plants mainly produced sinter feed, natural pellet fines, besides lump ore. However, with decreasing ore grades, size reduction now occupies a centre stage in nearly all new plants. Technologies used up to date for processing low-grade iron ores in Brazil, in particular itabirites, have consisted of three or four stages of crushing followed by ball milling. A number of new plants are either being built or are currently being designed that will process the same type of ore, so that engineers are investigating alternative comminution routes. The paper analyses comparatively four comminution routes for processing a particular itabirite ore, many of which using technologies and layouts that have not yet been used in such application. Using data from bench scale and/or pilot-plant tests, the different routes are compared on the basis of sustainability principles in accordance to the Brazilian energy matrix, which is quite particular. It is concluded that if the sustainability criterion is used, then the optimal route would correspond to a circuit that uses HPGR technology with truncated feed followed by ball milling. Given the particular case of itabirite iron ores and specially to the one in the present work and the source of Brazilian energy, it is evident that indirect energy expenditure in comminution plays a significant role in greenhouse gas emissions when compared to direct energy, being the reason for the great attractiveness of HPGR technology. Evidently that these will have to be balanced against CAPEX, OPEX, NPV and other qualitative criteria, which can certainly lead to a different optimal circuit.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini

Vertical ring and Pulsating Wet High Intensity Magnetic Separator (VP-WHIMS) is widely used for week magnetic mineral beneficiation or ferrous impurity removal from non-metallic minerals. Because of the complexity of this machine, mathematical modelling of its process is complicated and time consuming. In this paper, artificial neural network (ANN) and response surface methodology (RSM) were applied to evaluate the VP-WHIMS performance and optimize its main operating parameters in beneficiating of the Chadormalu hematite sample. The operational parameters of this magnetic separator are considered as: magnetic field intensity (2500-8500 gauss), pulsating frequency (20-100 %max), ring rotation speed (0.6-4.6 r/min) and slurry concentration (15-35 w/w %). Concentrate grade and recoveries (weight and Fe) are monitored as responses. Centre composite design (CCD) was used for experimental study. Four process variables were set using small CCD. Eight star points (a=±1), eight axial points (a=±2) and five replicates at the centre point (a=0) were chosen as experimental points. In ANN system, the best network topology was obtained as (4-5-3). The weights connection and biases were obtained using batch back propagation (BBP) method for 21 experimental data points. The results indicate that ANN

Jan 1, 2014

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By M. Mirnezami

Pentlandite samples were obtained as Ni concentrate from three Canadian plants and one specimen sample from Ward?s Scientific Establishment. The samples were upgraded using gravity and magnetic separation techniques. Nickel concentration was determined by atomic absorption spectroscopy. Microprobe analysis identified a range in Co and Cu lattice substitutions. All samples exhibited similar zeta potential-pH trend with isoelectric points from 2 to 3, and similar responses to copper activation and addition of xanthate. The similar trends indicate that the variations in lattice substitution identified have no significant effect on electrokinetic properties; that is, samples from any source likely yield results that can be generalized.

Sep 1, 2012

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By Tchingis Lekhatinov, Lev Filippov, Vyacheslav Severov, Alexandre Matinin, Victor Samyguin, Inna Filippova

"Comparison of flotation efficiency of the new multi-zone flotation cell (MZFC) and different conventional cells was carried out at lab and pilot scales on the various samples: high contrast pyrite tailings and old copper containing tailings. MZFC is a cell of intensive flotation, which provides optimal hydrodynamic conditions for all flotation sub processes. Enhancing of particle attachment, creation of conditions for coalescent flotation, selection of spatially separated zones according to optimal hydrodynamic conditions for flotation sub-processes are proposed as main principles to design an MZFC. The bubbles/pulp stratification was pointed out as a limiting step in the existing intensive flotation machines. Two strategies to improve bubbles/pulp stratification in the MZFC were studied: (a) impact of pulp-bubble jet to the surface of a prismatic insert inside of cell, which provides the detachment of low hydrophobic particles from bubbles, and (b) profiling the pulp/bubbles jet from the reactors due to a specific geometry of cell walls. The new continuous MZFC devices were demonstrated similar or higher efficiency in comparison with laboratory batch flotation cells for pyrite flotation. Higher flotation efficiency (82%) with pure pyrite concentrate (51.2% of sulfur) and a recovery level of 92% was obtained in MZFC when the cell with stratification by impact was used. Similar results were obtained with old Cu-containing tailings. Although MZFC had 1.5 times greater yields of concentrate than a batch flotation cell, it provided the increase of chalcopyrite recovery by 29.4% and concentrate grade by 4.8%. An original organization of pulp/bubbles stratification in the separator part of the new intensive flotation machine using variable geometry inserts allowed the best flotation selectivity with a bubble mineral loading coefficient 1.5 fold higher than the laboratory mechanical or pilot cells."

Jan 1, 2014

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By A. Y. Senchenko, Y. V. Kulikov

"The most common technique for selection of grinding equipment is the Bond method implying determination of a ball mill work index (BWi). The method is perfect for greenfield projects where a ball mill must be sized to grind an ore to 80% passing 75-100 µm. Finer grinding will require application of specific correction factors to a standard equation since initially the method was not designated for sizing of fine (minus 75 µm) grinding mills. Significant issues are related to selection of grinding equipment for treatment of originally fine materials when the standard procedure is not applicable. In 1984, Levin published his special technique titled as “A proposed test for the determination of the grindability of fine materials”, where he offered to use the standard Bond ball mill for determination of a specific grinding energy. However, this method did not meet with wide recognition. In 2017, Institute TOMS under guidance of JKMRC’s specialists performed a testwork aimed at verification of a new universal technique for determination of grindability of initially fine materials. An object was to test three aged tailings samples for the subsequent modelling of comminution circuit and evaluation of potential throughput of the existing ball mills with final grind size of ?80 passing 53 µm. In parallel with development of the universal approach, TOMS’ specialists carried out tests according to the Levin method in order to compare the data resulted from two methods. The results from lab ball mill testing on three products following the alternative test methods are presented in this paper along with the testing methodology and results analysis. Specific energy was calculated for regrinding of the materials to the required size. Difference of the examined methods and assessment of their applicability for sizing of full-scale equipment are explored."

Jan 1, 2018

By G. Mucsi, F. Kristály, Á. Rácz, É. Gregus, K. Bohács

"Stirred media mills are widely used in the industry for fine grinding. Most of the applications work in wet mode, however dry grinding in stirred media mill comes forward more frequently nowadays. The present paper deals with the differences and similarities of the wet and dry grinding in stirred media mill from energetic and mechanochemical point of view as well. Grinding experiments in batch stirred media mill were carried out with different materials. During the experiments zeolite and kaolin were used as feed material. The grinding experiments were carried out at different stress energy and stress number values; the grinding work was measured during milling. After grinding X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), particles size analyzes by laser scattering were carried out on the ground materials. As a result of the systematic grinding and analytical measurements a comprehensive comparison was carried out on the wet and dry grinding and their usefulness for mechanical activation in stirred media mill. INTRODUCTION The natural zeolites are crystalline hydrated aluminosilicates of alkali and alkaline earth characterized by the structure that contains frameworks responsible for the high cation exchange capacity (CEC) and absorption capacity. The frameworks are interconnected by cavities and resided by cations variable in size, coordinated by water molecules. Since zeolite comprises SiO4 and AlO4 tetrahedra interlocked by oxygen atoms that are situated in the structural nodes, their characteristics differ due to the varieties in the structure-directing agents and Si/Al ratio (Colella and Wise, 2014; Malekian et al., 2011; Terzic et al., 2017). The most common natural zeolite occurring in high amount, of industrial importance and involved in milling and MA is the clinoptilolite, in the literature equivalent to “natural zeolite” designated for high clinoptilolite bearing volcanic tuffs. Its amount in the host rock must reach ~ 40 % by weight to obtain the CEC and adsorption desired in its applications. In the highest quality rock might reach 80-90 % by weight (Favvas et al., 2016), but most often is the 40-60 % by weight content, associated with smectites, improving the CEC and adsorption of the tuffaceous rock. The application of such natural zeolites is problematic in many cases due to high silica (quartz, cristobalite and volcanic glass) content and beneficiation (concentration and extraction of pure zeolite) are not feasible. Thus, mechanical activation is a possible way to alter the other than clinoptilolite minerals generating high specific surface area and functionalized particle surfaces to enhance adsorption, reaction or particle adhesion. The zeolites easy availability and the utilization cost-effectiveness have prompted the research on their physicochemical and structural properties (e.g. adsorptive and molecular-sieve activity, heat resistance, and microporous cage structure) and finding new options for their application (Kusuma et al., 2013; Musyoka et al., 2014; Rida et al., 2013; Terzic et al., 2015b). Apart from the presence of exchangeable framework cations which are crucial for the adsorption ability, and a certain degree of pozzolanic reactivity. The thermal stability of dehydrated phases is another important characteristic for use of the zeolite in composite materials that are exposed to high temperature. Thereby, the zeolites found a wide application possibility in the design of the construction composites (Albayrak et al., 2007; Najimi et al., 2012; Vejmelková et al., 2015), as well as for resolving of the environmental protection issues like wastewater refining or heavy metal elimination (Gómez-Hortigüela et al., 2014) even from contaminated groundwater using passive methods like permeable reactive barriers (Gombköto et al, 2016). The grinding treatment of zeolite is a common and frequently applied procedure, both on laboratory (Bohács et al. 2017, Faitli and Czél, 2014)"

Jan 1, 2018