Search Documents

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Paul J. Axtell

The results of in-situ geophysical cross-hole tests on improved soil by soil mixing (SM) and jet grouting (JG) are described. This testing was conducted on soil improved by SM and JG columns constructed in the downstream free-field of Tuttle Creek Dam near Manhattan, Kansas as part of the seismic retrofit. Results of similar geophysical testing performed on untreated soil in the vicinity of the Downstream Test Program (DTP) area, as well as beneath the embankment at several locations, are also described and used for comparison purposes. In-situ shear moduli are also compared with those determined in laboratory resonant column tests. The increase in stress wave velocities and associated shear moduli by SM and JG treatment are presented for use in liquefaction potential and seismic deformation analyses of SM or JG treated soil. This data is required to determine the decrease in liquefaction potential and earthquake-induced permanent deformations due to SM or JG with respect to that of untreated soil.

Jan 1, 2008

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

1.1 The parties agree to submit all claims, disputes or controversies arising out of, or in relation to, the interpretation, application or enforcement of this agreement, including dispute resolution procedures, to sequential mandatory discussion, mediation and arbitration for resolution of all disputes before, and as a condition precedent, to self-help, arbitration, judicial action or other remedies. This mandatory procedure will resolve each dispute within one-hundred (100) calendar days. Any deadline falling on a federal holiday or weekend will be the next working day. Breach of this disputes process shall constitute a material breach of contract for which the aggrieved party may recover all costs, including attorneys fees, interest and other expenses necessary to resolve the dispute through litigation. The obligation to discuss and then mediate and arbitrate covers all disputes arising from every aspect of the Project to be built by the owner, including, but not limited to, design, engineering, bonding, indemnification, labor, material and services, and the acts or omissions of any related party for whom a party to this agreement may stand responsible.

Jan 1, 1994

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Eric S. White, Thomas J. Sabourin, Khuram R. Mohib

"This paper presents the challenges associated with the design and construction of a steel sheet pile cofferdam supported with one level of grouted anchors in clean to silty sand with gravel. The initial assessment of the subsurface conditions indicated loose to medium dense soil with intermittent dense to very dense layers with no occurrence of cobbles and boulders. Sheet piles were proposed to be installed to a depth of 24 m below the ground surface to limit dewatering requirements for the cofferdam. During sheet pile installation, refusal of piles occurred at multiple locations forming passages for increased flow into the cofferdam. Modifications were made in the design of the dewatering system as a result of the increased flow. Finite element modeling was used to select the necessary modifications to the dewatering system within the cofferdam. Wells were installed based on the findings of the numerical model. Model simulations showed good comparison with monitoring of the field installed dewatering system.INTRODUCTIONIt is necessary to consider the impact of the ground water, subsurface stratigraphy, strength, and drainage behavior of the soil for the design and construction of cofferdams. This paper presents a case history of the construction of a cofferdam in Northern Ontario, Canada. The project consists of the construction of a powerhouse, intake, and tailrace which will generate around 28 MW of renewable clean energy by diverting water from New Post Creek through a power house and discharge into the Abitibi River. The focus of this paper is the dewatering and excavation support required to permit construction of the powerhouse. The layout of the cofferdam is shown in Fig. 1. The cofferdam for the powerhouse is rectangular in shape with sheet piles on all four sides intended to be driven to the design toe El. 101 m. The east and west walls have a length of 46.3 m. North and south sides are 47.6 m long; and in addition, two cantilever sheet pile walls bound the tailrace on the west side and two cantilever walls were installed on the east for construction of the penstock inlet. The ground surface in the powerhouse cofferdam area, before commencement of sheet pile driving, was brought to El. 125; the ground then slopes up to the East, toward New Post Creek, and the site is bounded on the West by the Abitibi River. 186 pairs of sheet piles were used to create the cofferdam and cantilever walls. The deepest excavation is to elevation 114.4 m. Within the west half of the cofferdam footprint, the base of excavation slopes upward at 3H: 1V to facilitate the tailrace discharge into Abitibi River.SOIL STRATIGRAPHYThe cofferdam design was based on the geotechnical investigation conducted by AECOM (2014) which included two relevant boreholes near the powerhouse footprint. The ground elevation at the time of investigation varied between 131 to 129 m. The material observed to the full depth of investigation was comprised generally of coarse to fine sand and gravelly sand or a sand matrix with gravelly inclusions. Some intermittent layers of clay and silt intrusions were also observed. Generally the soils grade finer away from the river. SPT N60 values were recorded in two borings during the field investigation with values reported from 3 to 92. The in-situ conditions ranged from compact to dense with some loose and some very dense zones. Figure 2 shows the variation in SPT N60 values with elevation."

Jan 1, 2017

By A. Flora, E. Bilotta, F. Foria, V. Nappa

"All the typical applications of deep mixing rely on the good mechanical properties of the improved columns to strengthen or stiffen the ground for a number of geotechnical applications.This paper focuses on a completely different kind of deep mixing, carried out in order to obtain columns much softer than the surrounding soil. This kind of deep mixing, named Soft Deep Mixing (SDM), is introduced as an original means to tackle seismic risk, and can be convenient when the existing structure to be protected has a historic relevance that cannot be altered with structural modifications. The idea is that properly assembled layers made of partially overlapped SDM columns, with dynamic impedance much smaller than that of the surrounding soil, will filter and reflect most of the seismic energy.The paper presents the results of some 2D parametric numerical analyses aimed to investigate the seismic performance of this innovative approach. Simplified dynamic inputs (Ricker wavelets, having only one largely predominant frequency) were adopted to better understand the effect of signal frequency. The analyses show that the effectiveness of the soft grouted isolating barrier depends on soil and SDM geometrical, physical and mechanical properties, as well as on the frequency content of the seismic input.INTRODUCTIONPassive structural systems installed at the foundation level of existing buildings are a common solution to protect them against earthquakes. However, installation procedures are expensive and not always feasible, as for instance in the case of valuable buildings. As an alternative, ground improvement techniques can be used to modify ground properties, in order to mitigate the intensity of shaking at ground level. The propagation of shear waves in the ground can be modified by introducing a layer of artificially modified material, having a dynamic impedance (defined as n =p VS, where p is the material density and VS the velocity of shear waves) very different from that of the natural soil. Both very high or very low values of the dynamic impedance of the grouted soil (nt) can be effective in reducing the overall transmitted energy, with the difference that – for a given reduction of the transmitted energy - stiff grouted layers tend to filter the low frequency components of the amplitude spectrum without modifying in a significant way the high frequency components, while soft grouted layers have the opposite effect. Then, ideally the choice of the best grouting technique should be made considering the effects of the different frequency components on the building to be protected. These effects are detrimental for the structure when they are close to its natural frequency: high frequency components result into large structural loads on massive squat structures (high natural frequency), and low frequency components may be critical for tall and flexible structures (low natural frequency). Therefore, the typical procedure of stiffening the uppermost soil layers regardless of the kind of building to be protected is not necessarily beneficial, and for the case of squat structures soft grouting should be preferred. However, this procedure has not been taken into account yet in the engineering practice, and may pose static problems at ground level (i.e. excessive static settlements)."

Jan 1, 2015

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987