Search Documents

By Chengcan Wang, Jin-Tae Han, Young-Eun Jang

"The waveform micropile is a newly developed foundation type for increasing the bearing capacity with the created shear keys on the pile’s shaft. Analyzing the increment of resistance at the shear key zone is a crucial factor in the design of the waveform micropile. Hence, centrifuge tests were carried out employing six different models, including a waveform micropile in the axial loading condition. The analysis results of the load-settlement curves showed that the waveform micropile achieved a higher bearing capacity compared to the micropile without shear keys. In addition, the test results revealed that the load-settlement relationship was affected not only by the pile shape but also by the locations of the shear keysINTRODUCTIONA micropile is a small-diameter pile, typically constructed with a less than 300 mm diameter. Generally, the micropile’s construction involves drilling, grouting, and insertion of a reinforcement material, such as a thread bar. The micopile can be utilized in a variety of fields for reinforcing the foundations of existing structures. It also has advantages for accessing challenging areas like limited-access construction sites, including those with a low headroom space and adjacent structures, due to the small size of the construction equipment. Thus, since it was introduced in 1950 in Italy, the micropile has become one of the preferred solutions when other deep-foundation methods are not applicable to the site.Federal Highway Administration (FHWA) gives the micropile design implementation guideline of neglecting the end bearing due to its small diameter but considering the frictional resistance if the bond zone of the pile is in the soil or on a weak rock. The bearing capacity is considered primarily only if the micropile is founded on a high-quality sound rock (FHWA, 2005). Micropile design in South Korea is currently being performed based on the FHWA manual and taking into consideration the frictional resistance for the design as the pile generally sockets into a weak rock or soft rock. Moreover, the frictional resistance within the soil layer has usually been ignored, considering only the shaft resistance of the rocksocketed length in the conservative design. The design concept excluding the frictional resistance in the soil layer, however, may lead to an extension of the pile socket length, which will increase the construction cost. Hence, many researches have attempted to provide better design and construction methods to increase the bearing capacity in a cost-effective way (Juran et al. 2001; Sadek and Isam 2004; Tsukada et al. 2006; Finno 2002; Gomez et al. 2003; Seo et al. 2013)."

Jan 1, 2016

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

By Jr NeSmith

"Augered-cast-in-place (ACIP) pile installation technology has matured extensively since the first auger, pressure grouted pile was patented in 1959. The current technology allows for successful pile installation across a variety of stratigraphies to meet various project load resistance requirements. This paper presents an overview of current ACIP techniques by comparing a number of case histories in a variety of geologic settings from Eastern Pennsylvania, New York City and New Jersey to demonstrate ACIP pile constructability in soft soils as well as the penetration, and resulting significant loads resisted, of ACIP piles in dense soils and intermediate geo-materials. Geologic settings that will be discussed include the Piedmont and Coastal Plain geologic provinces as well as glacial till deposits. Keywords: Deep Foundations, Piles, Augercast, Augered-cast-in-place, Auger pressure grouted, ACIP, APGINTRODUCTIONThe author, along with two colleagues, published an article in Deep Foundations magazine (NeSmith et al, 2013) which described a number of the advances in equipment, techniques, installation monitoring and post-construction testing that have expanded the geologies in which Augered Cast-in-place (ACIP) piles are installed as well as increasing their efficiency in some traditional ACIP pile geologies. The author uses the term efficiency to refer to the load resisted by a pile of a certain diameter and the increased efficiency noted refers to increased allowable loads over those traditionally resisted by piles of certain diameter (or a reduction in pile diameter from that which was traditionally used to support a certain design load). The performance and installation of ACIP piles in a variety of geologies in the Northeastern U.S. are discussed herein.PIEDMONT PHYSIGRAPHIC PROVINCEThe Piedmont physiographic province stretches from Alabama to the east through Georgia and up the east coast, just west of the Coastal Plain to Pennsylvania and New York (Brown, 2002). It generally consists of soils weathered in place from the underlying bedrock, which is typically a combination of granite, schist and gneiss depending on the location within the province. The author’s experience in the Northeastern US has been on sites where alluvial or coastal plain soils overly the residual soils and partially weathered or intact rock of the Piedmont. The example presented here, from a site on Walnut St in Philadelphia PA, is representative of these projects."

Jan 1, 2016

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

By Ali Ebrahimi, Meena L. Viswanath, John F. Beech, Mustafa B. Erten, Ming Zhu

"Excessive deformation of a cantilever sheetpile wall can occur due to dredging, excavation, backfilling, or long-term creep behavior of soil. A buttressing berm constructed in front of the wall can be considered as a mitigation technique to prevent or decrease the deformation by increasing the passive earth pressure and thus improving the wall stability. The effect of the buttressing berm on the stability and deformation of a sheetpile depends on the berm geometry (i.e., the thickness/depth and the width) as well as the properties of the sheetpile and the adjacent soils. A parametric study was conducted using a conventional limit equilibrium method. Design charts were prepared to evaluate the effect of a buttressing berm and the soil friction angle on the wall stability and deformation. These charts can be used as a tool by geotechnical engineers to make a quick estimate of the required size of a buttressing berm in case of calculated or unexpected excessive deformation of a sheetpile. An analysis of the effect of a buttressing berm on the stresses and deformation of a sheetpile was also compared with the results from finite element analysis. The results of this comparison are discussed.INTRODUCTIONCantilever sheetpile walls are commonly used to support excavations. Sheetpiles are hot rolled or cold formed sections of steel made to interlock with adjacent sections to form a continuous structure providing lateral support. Sheetpile walls can be cantilever walls or anchored with tiebacks. To construct a cantilever sheetpile wall, sheetpiles are driven by pile drivers or vibrated in to a design depth sufficiently below the depth of excavation. Excavation can then proceed in front of the sheetpile wall, which resists the earth pressure loading from behind the wall. The design depth and geometry of the sheetpile wall depend on the soil conditions, the depth of excavation, and the tolerable deformation. In certain cases, when a small buttress of soil can be left immediately adjacent to the sheetpile wall, the required depth or geometry of the sheetpile wall can be reduced or adjusted, which can significantly decrease the cost of procuring and installing the wall. Such a buttress can also serve as a short-term or long-term remedy in case of observed excessive deformation in a constructed wall. Traditional methods of analyzing the stability of a sheetpile wall do not account for the passive pressure effects of this small buttress. In this paper, a parametric study was performed for a variety of soil types and wall and buttress geometries by implementing traditional limit equilibrium methods in commercial software and design charts were created illustrating the effect of a buttressing berm on sheetpile deflection. Selected cases were then modeled in a finite element software to compare the results with the traditional limit equilibrium method. The resulting design charts can be used as a tool by geotechnical engineers looking to reduce the design geometry of a sheetpile wall or address observed excessive deformation in a constructed sheetpile wall."

Jan 1, 2016

By John Vickers, William H. Hover, Paul C. Schmall

"Any sudden subsurface issue that threatens the stability of existing buildings or infrastructure is cause for immediate investigation and prompt remedial action. Nowhere is this more true than the nation’s dams and levees. A breach of any kind, no matter how small initially, has the potential to be catastrophic and impact a wide downstream area. Addressing the problem quickly and effectively is therefore critical. When a turbid water discharge developed from a rock drainage embankment at the toe of the earthen dam impounding Cannonsville Reservoir, near Deposit, NY, the source of the problem was quickly identified as resulting from an artesian water release from an underlying permeable silty sand and gravel formation during drilling of three exploratory boreholes in preparation for construction of a hydroelectric plant at the downstream toe area of the dam facility. Work was halted, intense 24-hour monitoring was implemented, and as a risk reduction measure NYCDEP began to draw down the reservoir’s total storage at a rate of a billion gallons per day. Input sought from contractors within the geotechnical community helped result in the design and development of a deep well system to control the artesian pressure. Once this primary objective was accomplished, modified compaction grouting was performed at the borehole locations to densify loosened soils, fill any voids created by the discharge activity, and seal off the permeable aquifer. This paper discusses the dewatering program, specialized drilling techniques required, monitoring and verification of pressures within the dam, and the grouting program.BackgroundCannonsville Dam, owned and operated by the New York City Department of Environmental Protection (NYCDEP), is located in Deposit, New York on the West Branch of the Delaware River and impounds the Cannonsville Reservoir. Built between 1959 and 1964, the dam has an impervious central and upstream core zone keyed into the glacial till foundation, a semi-pervious downstream embankment zone, and a rockfill toe and is approximately 2,800 ft (853.4 m) long and 175 ft (53.3 m) high. The dam is formed by two embankment sections. The left section forms the main embankment blocking the main river channel, while the right section is constructed over a topographic saddle or low ridge. Reservoir level is actively influenced by withdrawals through the West Delaware Tunnel, based on water supply need. Under normal circumstances, water is continuously discharged downstream to the Delaware River."

Jan 1, 2016

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

By Abid O. Adekunte, David Greentree, David Hilton

"The construction industry is witnessing an upsurge in demand by property developers to have basements incorporated into their residential and commercial development schemes. This is attributable to perceived improvement to aesthetic and commercial values of buildings by underground space, amongst property owners. This trend is compelling more owners of buildings with no basements to explore the possibility of creating underground additional space beneath their existing buildings. The creation of a basement beneath an existing building entails the installation of a reinforced concrete (RC) underpinning system, temporary works, bulk excavation to basement formation level and construction of the basement structure, with associated aesthetic finishes.The L-shaped segmental RC underpins are a common system of choice for such underpinning works. They are multi-functional; providing vertical support to the existing superstructure, providing lateral support to earth and groundwater, supporting temporary and permanent surcharge loads from adjacent structures and services, whilst also forming part of the basement slab. This paper focuses on the first function of the Lshaped RC underpins; capacity under vertical compressive loading from the superstructure. The most common industry approach for the prediction of vertical capacities of L-shaped underpins is the oldfashioned Meyerhof’s (1953, 1963) effective width method, which is based on the traditional bearing capacity theory, whilst accounting for correction factors for eccentricity and foundation depth.The traditional bearing capacity formula is surrounded by a significant degree of uncertainty; estimates are highly user-dependent, as capacity prediction is sensitive to the chosen angle of shearing resistance (?), while there are difficulties in accurately measuring the in-situ ??value of cohesionless soils. In addition, the effective width approach has been shown to be very conservative by many research workers. The segmental RC underpins presented in this paper have been designed with an alternative less conservative method, which involves the use of a recently proposed consistent work-hardening plasticity model calibrated with field-based tests on footings of various aspect ratios and relative embedment in sand. The paper highlights the principles behind underpinning works for urban basement construction, the design of L-shaped RC underpins with the recently proposed plasticity model and the advantages of the method over traditional bearing capacity solutions and pre-existing plasticity models."

Jan 1, 2016

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Arjan Jovani, Arjan Beqiraj, Përparim Alikaj, Altin Karriqi

"Koman dam is one of most important high dams in Drin River Cascade. Safety of these dam is very important not only in power production but also in social and environmental aspects connected with vital activity of local people living in downstream of Drini River and in economic development of the country. In December 2014, during the rehabilitation works on some protection measures at the downstream dam toe, a considerable amount of water leakage emerged from the dam toe. This was noticed even before, but its amount and physical-chemical properties were not evaluated. In order to study the origin and flow direction of this water leakage, KESH sh.a. (Albanian Power Corporation) realized Geophysical and Hydro chemical surveys, turbidity and flow measurements and respective analyses of them. Geophysical survey consist in Apparent Resistivity surveys and Self Potential survey. The survey was done in 3 lines using Resistivity “Real Section” technique. Results are plotted in Sections and plan maps of resistivity and SP parameter. There are defined possible leakage areas and the main flow directions are defined. Also, there is done a hydro chemical analyse. Nine water samples were taken from the different places as Komani lake, service galleries of dam, dam toe and two karst springs which were analysed for both physical-chemical parameters and isotopic composition of O-18 and D. The attained analytical data found that water from the dam toe leakages shows the same chemical signature and isotopic composition of O-18 and D as the water from the lake, thus confirming the hydraulic connection between them.Also, There is done the analyse of water leakage turbidity and amount of this leakage"

Jan 1, 2016

By Stephan A. Jefferis, Adrian H. Bath

"This paper draws together some themes on the durability of barrier systems, and particularly cementitious systems. For contaminated land and water retaining structures, durability can be poorly addressed at all stages of a project, from specification, to barrier material selection, barrier design including toe-in and through to performance assessment in operation. Permeability (hydraulic conductivity) is a dynamic property which will vary over time as reaction processes propagate through a barrier. However, laboratory testing, when undertaken, tends to be focused on short term tests with aggressive chemicals so that the effects of longer-term processes such as carbonation and leaching by permeating water are missed. For water retaining structures, carbonation and leaching actually may be the most significant processes affecting barrier performance as the groundwater adjacent to many water bodies can be otherwise rather benign (as regards bentonite and cementitious systems). These and other reaction processes have been modelled in the arena of nuclear waste repositories and procedures are well recognised. However, such procedures have yet to be widely adopted for the assessment of other barrier systems.INTRODUCTIONOver the last few decades there has been an enormous amount of laboratory research on the durability of barrier materials or more specifically papers reporting the results of permeability tests. Unfortunately there is a much smaller literature on scaling test results to barrier dimensions in the field or to required design lives. Although in the geotechnical industry durability research has been largely laboratory based, in the nuclear industry where relevant timescales are multi-millennia rather than decades, research has been heavily underpinned by geochemical modelling. A significant purpose of this paper is to examine the tools that may be used to analyse the results of tests on barrier materials used in geotechnical engineering, for example, for water retaining structures and contaminated land and draw the attention of the construction industry to the potential of the modelling procedures developed for nuclear repository assessments. Modelling can help to identify underlying processes and so augment information from laboratory testing focused on changes of physical properties such as permeability and strength."

Jan 1, 2016

By Marwa Nabil, Alaa A. Ata

"Recent developments in the analysis of piled rafts has incorporated the load sharing of the raft and the piles to support the superstructure. In the piled-raft system, piles are cast monolithically with the raft and the load is partly transmitted by the raft to the soil directly below it, and partly by the piles to more competent deep soil. While these piles are effective in increasing the bearing capacity and reducing the settlements, they often lead to significant straining actions at the pile head-raft connection which may constitute the weakest link. An attempt to provide a more economical solution, that at the same time overcomes this weak link, is to disconnect the pile heads from the raft and introduce an intermediate cushion of compacted fill. In this case, the piles are considered as reinforcement to the subsoil and will also act as settlement reducers. This paper investigates the load transfers mechanism of the unconnected piled raft with cushion using ABAQUS finite elements Program. The main objective is to provide an in depth analysis of the raft–soil–pile interactions in multi-layered soil under static and seismic loads. The investigated system provides an economical alternative for traditional connected piled raft foundation, where there is no need to reinforce the piles, no need for pile head demolition or expensive waterproofing of the pile head connection. Cost analyses of unconnected versus connected piled raft systems confirmed a cost savings in the construction that may reach from 50 to 70 percent.INTRODUCTIONDesigners around the world have gained more confidence to use the piled-raft as a more realistic system where the raft and the piles share transferring the superstructure loads to shallow and deep soil layers. A further advancement is to use unconnected piled rafts as another practical and economical alternative to the traditional piled rafts. Unconnected piled raft is also synonymous to settlement reducing piles; or simply, soil improvement piles. Liang et al. (2003) has extended the concept of pile-raft-foundation to a new type of foundation called composite piled raft foundation or unconnected piled raft foundation. The foundation is composed of a sand/gravel cushion sandwiched between the raft and piles. The piles group may contain short and long piles. The short piles are constructed of flexible materials such as soil-cement columns or sand-gravel columns, and are used mainly to improve the bearing capacity of shallow soft soil; the long piles, which are made of relatively rigid materials such as concrete, and their main function is to reduce settlements. The cushion plays an important role in mobilizing the bearing capacity of the subsoil and in modifying the load transfer mechanism of the piles. In Shanghai, China, this system of unconnected piled raft has proved to be quite suitable and effective in coastal areas, where deep soft soil deposits exist."

Jan 1, 2016

By Christopher R. Harris

"Considerations are presented for developing and implementing self-hardening slurry mix designs to be utilized in barrier seepage walls. Slag-cement-cement-bentonite (SCCB) slurries are the primary focus, with some comparisons referenced to the more traditional Portland-based cement-bentonite (CB) slurries. Field and laboratory mixing methods are reviewed, including 1) single sack – single mixer method; 2) bentonite slurry mixer – cementitious addition mixer method; 3) bentonite mixer – grout mixer – CB blending mixer method. Major phenomena associated with the dynamics of barrier wall excavation, such as loss of water from the in-trench slurry and consolidation of in-trench slurry are discussed. Other topics touched upon include sand content effects, fluidizers utilized, and chemical contaminants. The role of higher bentonite to water ratio is reviewed, with demonstration of improvement of filtration properties, and an increase of water retention of the final consolidated product.IntroductionSelf-hardening slurry has been utilized to construct barrier seepage walls for many decades. This is essentially a single-step slurry excavation and backfill process whereby the trench-supporting fluid gains strength over a short period during installation and maintains or develops low hydraulic conductivity. The resulting curing slurry becomes the actual barrier wall as the resultant cement-augmented clay slurry now fulfills the dual purpose of both temporary trench stabilization and final cured-in-place product. This eliminates the requirement and expense of subsequent backfill/slurry displacement operations required in traditional barrier wall installations.Self-hardening slurries have been fabricated using a number of various clays, most commonly sodium bentonite, calcium bentonite, attapulgite, and sepiolite. Perhaps due to plentiful high quality sodium bentonite deposits found domestically, the proven excavation stabilization properties imparted from sodium bentonite slurries, sodium bentonites are typically specified for formulating self-hardening slurries in the US. Cementitious materials utilized most commonly are Portland cement and slag (ground blast furnace slag or GBFS). For the purposes of this discussion, self-hardening slurry having a cementitious of Portland will be referred to as CB. Those having cementitious material of GBFS replacing Portland (partially or wholly) will be referred to as SCCB."

Jan 1, 2016

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By Mikael Calando, Thomas Joussellin

"San Francisco's rapid growth has caused the city to plan for the Transbay Transit Center Project, a visionary transportation and housing project, that will transform downtown San Francisco and the San Francisco Bay Area’s regional transportation system by creating a “Grand Central Station of the West” in the heart of a new transit-friendly neighborhood that will be home to more than 20 new towers rising a high a 1,070 ft. This paper describes the specificities of using advanced diaphragm wall technology, tooling, equipment and installation practices for deep foundation and permanent underground structures. In particular, this paper will emphasize on the urban constraints, geotechnical conditions, and the novel approaches adopted for the construction challenges of the Transbay Transit Center’s Load Bearing Elements, or Barrette PilesPaperThe Transbay Transit Center Project consists of the construction of a new multimodal, five-story Transit Center located in the South of Market neighborhood near the Financial District in San Francisco. The future Transit Center will incorporate nearly 83,000 square feet of retail, a 5.4-acre rooftop park, an extensive public arts program and bus ramps that will connect the Transit Center to a new off-site bus storage facility and the San Francisco–Oakland Bay Bridge. The new facility will accommodate more than 100,000 passengers each weekday and up to 45 million per year. Additionally, the new Transbay Transit Center will replace the since-demolished San Francisco Transbay Terminal, and nearly 20 towers, such as Salesforce Tower, will take advantage of the height increases allowed through the Transit Center District Plan.The approximately $4.5 billion project features a new five-story structure (including two underground stories) and new bus ramps which include a cable-stay bridge. The deep foundations for the pylon of the bridge (Pylon 9) consist of two each 21 ft x 5 ft barrettes (also called Load Bearing Elements in the US) extending more than 180 feet below grade and 10 feet into the bedrock. The barrettes were chosen because of the combination of high loads, significant depth and small footprint. The barrettes are installed using the Diaphragm Wall technology. Nicholson Construction was contracted by Shimmick Construction to install the cable-stay bridge’s foundation elements."

Jan 1, 2016

By Mark R. Svinkin

"Construction equipment and operations usually produce soil and structural vibrations which may harmfully affect various structures and also the content of buildings and houses. The level of structural vibrations depends on a number of factors such as characterized sources of vibrations, soil conditions, and susceptibility of structures. There are certain knowledge and experience for managing the effects of construction vibrations which require implementation of condition survey of structures, information on construction dynamic sources and soil conditions at a site, evaluation of possible vibration effects on structure, calculation of ground vibrations before construction, use mitigation measures to decrease vibrations, and a choice of appropriate vibration limits. The paper presents the application of known concepts for assessment of vibration effects on structures from bridge constructions.INTRODUCTIONVibrations producing by construction activities such as pile driving, dynamic compaction of loose soils, demolition work, heavy construction equipment and trucks can affect adjacent and remote structures. Vibration effects on structures, sensitive devices and processes may create significant practical problems. Legal actions are often required for solutions of vibration consequences. The level of construction vibrations depends on dynamic sources, soil conditions at a site in particularly availability of soils with settlement potential, distances from the sources, parameters of waves propagating at a site and susceptibility rating of adjacent and remote structures. It is likely that intolerable structural vibrations from direct vibration effects of impact pile driving and resonant floor vibrations from vibratory pile driving may be induced in adjacent structures to construction sites.Foundation settlements resulting from soil vibrations in loose soils usually occur in the proximity of dynamic sources, but it is important that dynamic settlement may happen at various distances from the source. There are such examples. First, Kaminetzky (1991) mentioned a case history of building settlements developed at a distance of about 305 m (1000 ft) away from a pile driving site. Foundations of the buildings were underpinned on piles down to the tip elevation of the new driven piles to prevent building settlements. Second, Lacy and Gould (1985) shows that the peak particle velocity (PPV) of 2.5 mm/s (0.1 in/s) of ground vibrations could trigger dynamic settlements at distances up to 30.5 m (100 ft) from driven piles."

Jan 1, 2016

By Hayel M. El-Naggar, Mohamed Sobhi, Mamdouh M. Hamza, Marawan M. Shahien

"This paper presents the results of two lateral load tests on large bored piles in soft clay deposit for a major site in northern Egypt. The tests are carried out on 0.8 m diameter piles. One of the tests is carried out on the pile where the clay starts from the ground surface. The other test is carried out on a pile after surface improvement by replacing the top 1.50 m of the clay deposit by compacted granular soil. The results of the tests show the influence of the surface replacement layer on the lateral load versus lateral displacement relationships of the loaded pile. The results of the two tests are used to calibrate a 3D Finite Element Analysis model for the pile. The model is used to investigate the influence of the thickness and lateral extent of the surface replacement layer on the behavior of laterally loaded large bored piles.INTRODUCTIONLateral loads for piles are produced by seismic events, wind, wave action, ship impact, traffic, and land slide forces. The lateral resistance of a pile is controlled by the stiffness and the strength of the material of the pile and the soil surrounding the upper portion of the pile. In most situations, the soil surrounding the upper portion of the pile is too weak to sustain the design lateral loads. Thus there is a need to increase the lateral resistance of the pile or groups of piles. Such an increase may be achieved by either increase number of piles or increase pile diameter. Alternatively, an economic way to increase the lateral resistance is to improve the soil surrounding the upper portion of the pile (Rollins and Brown, 2011; Faro et al., 2015).Ground improvement has the ability to increase the lateral resistance of the pile by increasing the passive resistance of the soil surrounding the upper portion of the pile. The ground improvement techniques have the potential for being more cost-effective and reducing construction time. In spite of this fact, such techniques are rarely implemented in practice. Further, there are relatively few tests or records available in the literature to guide engineers in evaluating the actual effectiveness of this approach. In addition, there is no standard or methodology to aid engineers in designing increase of lateral resistance with surface ground improvement. There are specific improvement methods for each soil type, whether it is loose cohesionless soil or soft cohesive soil and these methods are provided by Michell (1981), Tershai and Juran (2000), ASCE (1997), and Rollins and Brown (2011). Furthermore, there are number of case histories that add a new hole in the sight, such as the cases provided by Brown et al. (1987, 1988), Mokwa and Duncan (2001), Rollins et al. (2005), Rollins and Cole (2006), Cole and Rollins (2006), Rollins, Snyder et al. (2010) , Rollins, Gerber, and Kwon (2010), Rollins and Nasr (2010), and Gerber et al. (2010)."

Jan 1, 2016

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016