Search Documents

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By Darrell L. Beddard

The test program information provided for some immediate changes on the upcoming contracts and in contract administration for the I-880 Replacement Project. Plan sheet modifications included changes to the pile data tables showing the actual demand load required for structural stability. The normal class of pile with a minimum load carrying capacity was removed. This provided for substantial pile length reduction at several locations since the structural loading was much less than the predetermined pile class ultimate capacity. New specifications were developed and standard specifications were modified to accommodate the newer foundations, installation procedures and pile acceptance criteria. Current Caltrans specifications require that the Contractor provide bearing capacity at the specified tip elevation. This requirement was removed and pile acceptance was determined by the Engineer. Acceptance criteria was established by the State and was based on. set-up trend over time. Static loading tests were reduced especially in areas where testing was performed on the indicator program. Testing procedures were modified and set-up periods were established before piles could be tested. For the contract near the San Francisco Oakland Bay Bridge (Unit E) the FHWA 1000 tons (8.9 MN) test beam configuration was completely changed. This provided added safety and allowed more tolerance in the pile placement for the testing operations. Indicator piles were added as companion piles to the static loading test piles. These piles were used for restrike events which included collecting dynamic data for calibrating the wave equation analysis with static load test results. Indicator piles also provided quick access for restrike events, where as, the static loading test pile needed modification to perform the restrike operation. Penetration rates were recorded for these operations. Wave equation Analysis Program (WEAP) was used in developing the acceptance criteria. The standard Engineering News Record (ENR) formula in the current Caltrans' Standard Specifications was removed for the contracts. Contractors were required to submit, prior to driving piles, a driveability study for their contract. These studies required discussion of their operations, method of installation, effects of soil set-up, set periods, hammer settings, bearing graphs, inputs to the WEAP program and complete a "Pile and Driving Equipment Data" form. Dynamic monitoring was detailed in the specifications on how the monitoring process was to occur. Set periods were established and restrike events were called out with the frequency of these events.

Jan 1, 1996

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1996

Jan 1, 1996

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Armin W. Stuedlein, Steven R. Saye

The differences between calculated axial pile capacity and the capacity realized during and following installation has long presented a significant concern for foundation engineers and contractors. Such differences have increased in prevalence with the increased use of larger diameter steel pipe piles and the significant increase in design-build contracting. The writers present concepts to close the gap between calculated axial pile capacity and the capacity realized during and following installation of driven pile foundations, including: (1) pile set-up in plastic soils, (2) limitation of re-driving of piles after setup which serves to reduce pile capacity, (3) the use of a vibratory hammer to install piles in cohesive soils disturbs the supporting soils and reduces the pile side resistance capacity significantly, and (4) long pile installation times for open-ended piles can damage the pile side resistance. Examples are presented from practice to illustrate these concepts and to guide pile installation planning to recognize the installation impacts and either consider alternate installation approaches or to properly consider the installation impacts during design.

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Debra F. Laefer

Jet grouting is a ground improvement technique that has become widely adopted over the past three decades, yet relatively little data has been published about performance characteristics of mixes under adverse conditions, such as the inclusion of clay lenses. This paper presents an experimental investigation on the impact of clay on the strength of jet grouting. A total of 150 grout samples were subjected to 0-10% levels of Kaolinite and Bentonite inclusion. While the Bentonite was introduced as a pre-hydrated slurry, the Kaolinite was mixed in two ways: in a pulverized condition and as large chunks. Sample strength and stiffness were measured at multiple dates within the first 28 days. With 10% clay inclusion all samples exhibited significant strength and stiffness losses. With some, substantial losses began with as little as 4% clay. Even a 1% clay inclusion tended to decrease strength and stiffness between one-quarter and one-third of the control sample. Depending upon clay type and inclusion method, results differed significantly with respect to strength and stiffness development and failure mechanism. Petrographic analysis is used to provide further insights as to apparently divergent behaviors.

Jan 1, 2009

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Heman Manchanda, Sandeep Sharma

Several infrastructure projects are in various stages of construction and planning in India and almost all of them involves open ground excavation extending to varying depths. These structures are generally multipurpose and fulfil several needs of the society, their failure can be catastrophic. The design and construction of deep open excavations is generally associated with a high level of risks due to a whole series of uncertainties involved, and the success of such projects depends on various factors including appropriate evaluation of ground behavior and response to excavation stages, correct choice and analysis of construction supports, control of ground water flow during excavation, etc. One of the most critical amongst all these is ground water flow during construction and stability of underground excavation depends to a large extent on ground water control. This paper uses numerical studies for the assessment of the potential impact of ground water and ground water movement for the design of underground deep structures. The studies are being conducted using PLAXIS 2D finite element software and analysis all construction stages to which an open underground excavation shall be subjected. The paper discussed in detail the impact of water table fluctuations and comparative evaluation of different water flow conditions – a) Different Stages of excavation in line with the construction sequence (Phreatic), b) Coupled flow analysis (Transient- 1 year and 2-year duration) and c) Steady state flow conditions. The paper also covers seepage calculation and design of dewatering system.

Sep 1, 2022

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By Tsunenobu Nozaki

"Basically, the “Press-in Piling Method” was invented to eliminate construction nuisances, such as noise and vibration which have been serious unsolved problems for advancing societies over a long time. In the construction industry, piling works have been a major cause of noise and vibration, because most piling methods utilize dynamic load to install piles into the ground. The secret of the Press-in Piling Method is to utilize static loading to install pre-formed piles rather than dynamic load. The piles are hydraulically gripped and jacked into the ground by the special piling rig known as the “Silent Piler”. Therefore, the piles can form a robust and firm foundation, which is another advantage of the Press-in Piling Method.The Press-in Piling Mechanism and Implant Foundations The basis of the Press-in Piling Method is simple. The Pres-in Piling Machine installs a preformed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles, which are called “Reaction Piles”. Due to this, the Press-in Piling Machine can produce a powerful piling force whilst only requiring minimal machine size.With the Press-in Piling Method, as piles are pressed into the ground, they are incorporated with the surrounding soils, which provides a large bearing capacity and passive horizontal resistance. These embedded foundations which are firmly anchored into the ground are known as “Implant Foundations”. Being embedded into the ground, the foundations are resilient and maintain their serviceability even in the worst credible design conditions."

Jan 1, 2015

By Ray Zelinski

Caltrans sponsored a research project in 1992 which incorporated proprietary and generic pile types. The piles were subjected to axial tensile/compressive loads in deep, soft soils. Descriptions of various pile types and systems, scenarios leading to the proposal to test the systems, and load test results were/will be provided by other presenters at this seminar. Therefore, this paper will focus on the issues surrounding use of test results and proprietary pile systems on Caltrans construction projects. The primary issues facing Caltrans during implementation are as follows: 1) producing pile cap designs for a range of pile types and loads; 2) providing construction specifications which allow fair competition among the system vendors, yet assure design and ultimate capacities; 3) Develop quality control standards for pile system materials and installation techniques which guarantee pile durability for static and dynamic loads; and 4) assure that foundations have adequate lateral capacity.

Jan 1, 1993

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Oct 1, 2021

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Sep 8, 2021