Search Documents

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Philippe Monier, Frank C. Basham

"This paper outlines the scope and applications of 'COALMOD', the British Columbia Ministry of Energy, Mines and Petroleum Resources' computerized financial simulation model for coal mining developments. After a description of the computer system and language of implementation, the logic and scope of current model sub-routines are presented. This is followed by a presentation of examples on the current applications of the model to public policy evaluation, including benefit-cost analysis, fiscal analysis and evaluation of the effects of public infrastructure investments made in support of mining projects.IntroductionThis presentation has been developed in response to a number of requests from coal mining companies and various public agencies who have indicated interest in understanding our application of contemporary analytical techniques to public policy in the coal sector. In particular, the subject of this paper is an explanation of COALMOD. a mnemonic given to a computerized, mine-specific, financial simulation model which is assisting the Government of British Columbia in evaluations of new coal projects, assessment of public sector investments made in support of these projects and. more generally, measurement of the financial effects of current or proposed government policies, and factors outside immediate government control such as coal prices and transportation costs."

Jan 1, 1981

By J. E. Carter, D. P. Wall

"This paper details the highlights of the open-pit and underground operations of Mclntyre Mines Limited in the Smoky River area of Alberta. Mining methods, operating equipment and manpower are outlined, followed by a discussion of reclamation and environmental control.IntroductionMcintyre Porcupine Mines Limited was incorporated in 1911 and for many decades was known primarily as a gold producer in the Porcupine district of northeastern Ontario. The company, however , has held coal leases in the Smoky River area, near Grande Cache, Alberta, since 1921. Preliminary studies were carried out in the region from 1959 to 1963. In 1964, Mitsubishi, a leading Japanese trading company, (on behalf of Mcintyre), investigated the area as a possible source of coal for the Japanese steel industry. The initial report concluded that Smoky River coal was of high quality, comparable with some of the best metallurgical coals in the world."

Jan 1, 1981

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By John E. Udd, Peter Leinberger, Roman Kozarycz

"This paper is based on work done by the authors in a study of the structural features at a quarry excavated in Chazy limestone on the Island of Montreal. Observations on failures on the quarry walls and benches were recorded, and back analyses of small-scale failures were carried out, thus enabling an assessment to be made of the in-situ strength properties of the rock. Using this information, and data from shear tests in the laboratory, the authors made an analysis of the stability of the south wall of the quarry.IntroductionQuarrying, and excavating for foundations, in the Montreal area involves the removal of million s of tonnes of rock on an annual basis. Even when compared with the quantities mined at major open-pit mining operations, the production figures are impressive. At present, for example, crushed stone is produced at almost 20 quarrying operations either on, or near, the Island of Montreal. The annual capacities of the larger quarries are in excess of one million tonnes each. Lesser, but still substantial, production is achieved at the smaller quarries.Excavations, for foundations , especially during periods of peak construction activity, must also involve large quantities of rock . The writers, however , are not able to produce an estimate of the actual annual tonnages originating from excavations."

Jan 1, 1981

By Graham A. Karklin

"The Echo Bay Mines silver property is located 875 air miles north of Edmonton, Alberta. The mine is on the east shore of Great Bear Lake at Port Radium which is twenty six miles south of the artic circle, in the North West Territories.HISTORYThe area was first surveyed by J. Mackintosh Bell of the Geological Survey of Canada in the early nineteen hundreds. In May 1930, Gilbert LaBine staked claims at Port Radium called ""Cobalt"" and ""Cobalt I"". What he had discovered was an extremely rich vein of pitch-blend. These claims were the birth of mining in this area. The first ore shipment of pitch-blend was hand-picked and flown out of Port Radium in 1931. LaBine's discovery of pitch-blend became of world-wide importance with the outbreak of World War II. In 1939 the splitting of the uranium atom brought this area into world focus. It is generally believed that it was ore from this area that was used in the production of the devastating bombs which were dropped on Japan.It was at Port Radium that the leaching process for uranium extraction was pioneered. The resultant methods have been modified and adopted for use around the world. The mine was originally owned by Eldorado Gold Mines Limited. Echo Bay Mines leased the property in 1964, subsequently purchased it, and have been producing silver and copper every since."

Jan 1, 1981

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By P. E. Weidmark

"Energy, Mines and Resources Canada has published the first in a new series of reports that will examine selected mineral products that are imported.""Vanadium - An Imported Mineral Commodity"" looks at one of the 32 raw materials for which Canada currently is totally dependent on foreign sources of supply. Vanadium is used in Canada mainly as an alloying element in the manufacture of high-strength, low-alloy (HSLA) steels.The series will examine the supply systems for various selected imported non-fuel minerals, as an aid to developing policies that might lead to reduced dependence on external sources. Each report in the series will address a numberof questions:What countries do the mineral and its principal sub-products come from?How do they get to Canada?What are they used for?How vulnerable is the supply chain to disruption?Are there alternative sources?Are substitute materials available?In summary - how serious is Canada's supply problem for the mineral in question, and what should be done about it?Mineral Bulletin MR 188, ""Vanadium - An Imported Mineral Commodity"", is available for $3.00 ($3.60 outside Canada) from authorized government bookstore agents and many other bookstores, or by mail from the Canadian Government Publishing Centre, Hull, Quebec, KIA OS9."

Jan 1, 1981

By Eric R. Skonberg

"Technology exists today to blind drill a mine shaft 20 feet in diameter, unlined, over 3,000 feet deep. These shafts must be lined in the most economical, safe and expedient manner possible. A new technique of stacking precast concrete cylindrical sections in the unlined shaft has been developed to yield a dry and hydrostatically lined shaft .These sections must withstand an external radial pressure of 3,000 feet of water yet take up as little room as possible in the shaft . Using high-strength concrete, wall thicknesses may be kept at 2 feet. The outside diameter of the sections has been chosen to be 18 feet to allow for some annular space between the liner and shaft wall. The concrete sections are produced in segments 10 feet long weighing 75 tons each. During drilling operations, the concrete sections are cast and cured. After drilling operations are complete, a headframe is situated over the shaft. The unlined shaft remains full of fluid. A special liner running tool is mated with the section in three steel ports at the bottom of the section. The section and running tool are lowered into the hole, and the tool is disconnected and returned to the surface. Subsequent sections are lowered and stacked using the same operation. Grout is placed behind the liner to result in a dry shaft."

Jan 1, 1981

By D. Mills, W. H. S. Lawson

"The need to make repairs is seldom a major consideration in the design, fabrication and installation of major components of electrical generation plants. Repair welding, however, is a fact of life in the electrical generation industry, for restoration of degradation in service, from cavitation of hydraulic turbine runners, to corrosion and fatigue damage in pressure vessels. In making weld repairs to carbon and low-alloy steels, the largest source of trouble is hydrogen embrittlement and related post-weld cracking. Various strategies have been developed to control problems from this source, including post-weld heat treatment, the use of nickel-base alloy filler metals and the temper bead welding technique. Each of these basic strategies is being applied as circumstances require; each strategy must, however, be implemented in a manner that reconciles weldment structure and hardness, degree of restraint and service environment with the consequences of unsatisfactory performance of the repaired component.IntroductionMajor working components of electric generating plants are specified and installed on the basis that, wherever technically and economically feasible, they will retain functional capacity without major repairs for the twenty-five-plus years of normal plant lifetime. Nevertheless, repairs are often required, and welding is usually an essential feature of the work. Remedial welding may be performed to correct design or fabrication errors which become evident only at the time of component installation. The most common causes of requirements for repair involve corrosion, fatigue or related processes which prove more aggressive than expected during service. Increasingly, our planning for future repair requirements is related to continual improvements which are occurring in nondestructive evaluation technology. As components are periodically reinspected during their service life, fabrication induced defects may be revealed for the first time quite late in the life of the component. When this occurs, repair must be considered wherever inaccessibility of a flaw makes it impossible to prove its inactivity. Finally, there are certain components, for instance in hydraulic turbines, which cannot be economically made or used without the expectation of service induced wear. Here, periodic maintenance welding must be regarded as a normal event."

Jan 1, 1981

By P. W. Percival, J. J. Janssens

"Whitehorse Copper is a 2600-ton-per-day underground copper mine located within the city limits of Whitehorse, Yukon . In early 1978, due to increasingly difficult ground conditions. it was decided to investigate the conversion from longhole open stoping to vertical crater retreat mining. On-site crater testing by C-I-L demonstrated the feasibility of V.C.R. mining at Whitehorse Copper.After some investigation. a down-the-hole drilling rig was chosen and drilling began in November /978. Blasting began in June /979. and to September 1980 approximately one million tons of ore had been blasted. In-field changes to both drilling and blasting techniques have been implemented. Some of these changes were dictated by problems encountered; others were made to improve efficiencies.To date. V.C.R. mining has proven successful from a drilling and blasting aspect.IntroductionWhitehorse Copper Mines Ltd ., a division of Hudson Bay Mining and Smelting Co., Limited , is a 2600-Lp.d. underground copper mine. The plant site is located I mile west of the Alaska Highway, and approximately 7 miles south of Whitehorse city center. Production is from the Little Chief orebody, and total output is from vertical crater retreat stopes.The Little Chief and Middle Chief orebodies at Whitehorse Copper had original reserves in excess of 6 million tons, most of which graded 2.00/0 copper or higher . The orebodies are typical skarn deposits that have developed along the contact between an intrusive diorite and a limestone-quartzite flank pendant. The limestone has been metasomatized to form a calcium-magnesium skarn which, along the limestone / quartzite contact, has locally further developed into a mineralized magnetite-serpentine skarn. The principal copper minerals are bornite and chalcopyrite, with minor chalcocite and valleriite. Skarn gangue minerals are serpentine, diopside, garnet, epidote, calcite and wollastonite. Appreciable values in gold with some silver are present and recovered as well."

Jan 1, 1981

By Douglas C. Fraser

"Geophysical data are often presented on maps, sections or profiles with minimal data processing. A common example is magnetic data, in which the diurnal-free raw readings are merely contoured on a map. Other examples include profile presentation of VLF-EM data, IP pseudo-sections and airborne EM anomalies which may be shown on a map with only the measured amplitudes indicated.In recent years, efforts have been directed to the portraying of data in more useful forms. A number of algorithms (i.e., manipulative procedures and equations) have proven to contribute significantly to the usefulness of geophysical data. Some can be applied manually; others are sufficiently complicated to require a computer. Some merely alter the data to a more useful geometric form without altering the units. Others yield quantitative estimates of source body parameters such as conductivity and shape. Several examples follow:1. A simple algorithm is in common use which transforms noisy non-contourable VLF-EM data into less noisy contourable data. The input is the dip angle in degrees or per cent and the output is also in these same units.2. A simple algorithm has recently been developed which allows multi-level dipole-dipole IP data to be contoured on a map. Again, the units are not altered.3. A relatively complicated algorithm is in common use which transforms non-contourable height-sensitive helicopter EM data into contourable resistivity data,4. An algorithm has been recently developed which transforms non-contourable height-sensitive EM data into contourable weight per cent magnetite.The purpose of all the above techniques is to present the data in a simplified form. This, in turn, allows an easier assimilation by the user of much of the information content of the data."

Jan 1, 1981

By T. G. Carter

"This paper traces the introduction and use of fire-resistant (FR) fluids in hydraulic systems at underground mines in British Columbia. Reasons are given for the decision to make compulsory the use of such fluids in underground mines after January 1, 1975 by provincial government legislation. Examples are quoted of fires caused, or supported by, mineral oils which have resulted in loss of life and property.The basic principles of hydraulic systems are reviewed in order to present the effects of changing a system operating on mineral oils to one which must operate on FR fluids. Approximations of the cost of system conversions are given for certain machines and a brief survey is made of the various pieces of underground equipment which contain hydraulic systems operating on FR fluids.IntroductionIn 1948, Admiral Ben Moreel , who was then president of Jones and Laughlin Steel Corporation in the United States , wrote:""Although safe and healthful working conditions can be justified on a cold dollars-and- cents basis, I prefer to justify them on the basic principle that it is the right thing to do. ""(1)This paper will outline the introduction and use of fire resistant fluids at mine operations in the Province of British Columbia. That it was the right thing to do in enhancing the safety and well-being of every person employed at the mines was the prime consideration. That it may be justified on a cold dollars-and-cents basis is left for the reader to judge. The prime purpose of this paper is not so much to trace the efforts made by the individual mines to successfully introduce and use fire-resistant (FR) fluids in hydraulic systems, but to present an over-all picture of what occurred, in a collective sense, at the majority of mines which have ended up with a working FR fluid system. The problems attendant to the introduction of an FR fluid will be recounted in a manner which, it is hoped, will prove useful to those contemplating system conversions. Because the predominant fluid now in use is an invert, or water-in-oil. emulsion, this will be the FR fluid considered.Fluid Loss from SystemsThe quantities of various fluids required for use in hydraulic systems are extremely high. This statement in itself may appear to be redundant in that the capacities of the various systems should demand that a fixed amount of fluid is required for the initial filling of a system, with a further amount of fluid scheduled for use during subsequent fluid changes, i.e. at the recommended change intervals . If only this were the case!"

Jan 1, 1981

By Roger D. Plouffe

In today's mining industry, it is possible to retrieve, from small-diameter holes, geophysical data for qualitative interpretation in exploration and quantitative interpretation in the development of orebodies. The primary objectives in the exploration stage are to identify where, within a hole, economic minerals are, and to help in lithological interpretations. Other aspects, which are more quantitative, are the interpretation of downhole logs for parameters which can be used in surface geophysical methods (i.e. density for gravity surveys, acoustic velocities for seismic surveys, and magnetic susceptibility for airborne and ground magnetic surveys). Recent advances in equipment design, portability and durability have made downhole logging in exploration more inexpensive and reliable. This new equipment is being used to generate very precise quantitative results. This is especially true on uranium development projects. The interpretation of gamma logs for eUJOS values has finally become precise enough that they have begun to replace chemical values in reserve calculations. Another part of development data is density and equilibrium information, which, with today's technology, is being derived from downhole probing. In the years to come, the trends for many metals are toward neutron activation techniques, or "in-situ assaying", and the use of multiple logs for better lithological and physical rock property determinations.

Jan 1, 1981

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division's energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee's responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981