Search Documents

By Owen Owens, W. P. Armstrong

The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors' experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By Robert B. Parsons

"During hard times, the focus on tax issues makes a slight change in direction. Mining companies contemplate the tax treatment of transactions and circumstances which are the product of a difficult financial environment. Some of these issues are discussed in this month's edition of Tax Notes.Every industrial sector in Canada is undergoing a major restructuring of some form, and the mining industry is not an exception. The longest recession since the Great Depression continues to affect the economy. Mining firms seek to bring their debt/equity ratios into line, and try to replenish depleted retained earnings by selling assets. This month, Tax Notes briefly examines some of the tax issues which are generally encountered during the course of such a restructuring process.Debt SettlementOne question which commonly arises during hard times concerns the tax treatment of a "" gain "" realized by a debtor on the settlement of a debt. Consider, for example, a simple situation where a creditor wants to protect itself from further losses, and makes a deal with the mining company to accept a cash payment of $8 million in full settlement of a $10 million loan. In financial terms, the debtor has made a $2 million gain on the settlement of the debt. What is the tax treatment of that gain?The Income Tax Act (the Act) contains provisions in section 80 of the Act and in section 5400 of the Income Tax Regulations which deal specifically with this question. First of all, it is noted that the $2 million gain is not brought directly into income for tax purposes. However, as indicated below, the gain could affect the debtor's income indirectly to the extent that certain of the debtor's tax pools must be reduced by the amount of the gain."

Jan 1, 1993

By L. A. Melis, A. R. Marchbank, S. A. Webster

"Certain northern Saskatchewan uranium ores have a high content of nickel and cobalt which offer the potential for recovery as a by-product to uranium. A nickel/cobalt recovery process has been developed as a viable method of recovering a marketable concentrate from typical uranium raffinate solution.Impurities are first removed from the raffinate and the pure solution is then treated with sodium carbonate to recover a bulk nickel/cobalt carbonate precipitate for sale to a primary nickel producer. All contaminants of concern are removed to very low levels and the product is free of radioactive contamination with gamma emissions significantly below natural background. Cost estimates have shown that installation of a nickel/cobalt recovery circuit within a uranium process plant is economically feasible.The testwork that led up to the selected process is described along with recommendations for further investigations such as additional testing of hydroxide precipitation as a possible viable alternative to carbonate. The selected process is described and project economics are briefly reviewed.PROCESS TEST PROGRAMBackgroundExtensive metallurgical research has been performed over the years to develop a process for recovering uranium from the Midwest deposit in northern Saskatchewan. During the course of this research, a certain amount of information became available which suggested that recovery of nickel and cobalt from uranium raffinate could be economically feasible. It was decided to undertake a test program which would investigate methods of separating nickel and cobalt from radioactive and other metal contamination to permit production of a saleable product.Available technology suggested that three general approaches could be taken to recover nickel and cobalt. The first and simplest approach would be to selectively precipitate the impurities of concern, primarily arsenic, iron and radium, and then recover a bulk concentrate from the purified raffinate. The second approach would be to purify the raffinate and then remove cobalt from solution by solvent extraction producing pure nickel and cobalt solutions for further treatment. The third approach would be to precipitate all metals from solution and then selectively re-dissolve nickel and cobalt in ammoniac solution which would be further treated by solvent extraction for nickel recovery, leaving cobalt for further treatment."

Jan 1, 1993

By J. A. Meech

"The technology known as Expert Systems is being used within the minerals industry in a wide variety of problem areas. Applications include diagnosis, prediction, training, monitoring and control. Expert Systems provide a way to program computers to imitate human thinking. The construction of such systems is a straight-forward task that can be quickly learned by novices but can require a lifetime to master.To assist in the understanding and utility of this technology, a special manual bas been prepared which operates on a microcomputer under the MS-Windows environment. The manual covers all aspects of Artificial Intelligence of relevance to Expert Systems. A hypertext system allows users to probe as d•~ply as needed to achieve understanding or to simply skim the surface of the knowledge to obtain a quick overview of subjects. The manual was developed under the sponsorship of the Mineral Sciences Laboratory of CANMET and is available from the Mining and Mineral Process Engineering Department at the University of British Columbia. Annual updates are planned to keep abreast of new developments in this rapidly changing technology. RESUMELa technologie: des Systèmes Experts est utilisée par l'industrie minière pour résoudre une grande variété de problèmes. Les domaines d'application comprennent le diagnostic, la prédiction, la formation, la surveillance et le contrôle des procèdes. Les Systèmes Experts permettent d'écrire des programmes d'ordinateur qui imitent le processus de la pensée humaine. La construction de tels systèmes e:st une tâche qui peut être apprise rapidement mais qui peut prendre des années à maitriser.Pour aider à mieux comprendre et utiliser cette technologie, un manuel spécial opérant sur microordinateur dans l'environnement Windows a été développe. Le manuel couvre tous les aspects de l'intelligence artificielle qui concement les Systèmes Experts. Un système ""hypertexte"" permet à l'utilisateur d'étudier un sujet en profondeur ou de simplement couvrir une grande variété de sujet en surface. Le manuel a été développe avec l'aide financière du Laboratoire des Sciences Minérales de CANMET et est disponible au Département de Génie Minier et Minéralurgique de l'Université de la Colombie Britannique. Des mises à jour annuelles sont prévues de manière à couvrir les changements et nouveautés de cette technologie en évolution."

Jan 1, 1993

By George J. Simandl, Suzanne Paradis, Kirk D. Hancock, Jana Simandl

Traditional prospecting and boulder tracing are the two most important field techniques used in exploration for magnesite deposits hosted by sedimentary rocks. Consequently, success depends largely on the prospector's ability to identify magnesite. A density agent called sodium polytungstate (3Na2W04·9WOj'HPJ was successfully used to determine the presence of magnesite in sedimentary carbonate rocks of southeastern British Columbia. A rapid field method was developed and tested. This method permits discrimination between limy dolomites, dolomites, magnesite-bearing dolomites and magnesite-rich rocks.

Jan 1, 1993

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

"The Dome Mine, located in South Porcupine Ont. has been in operation since 1910 and is owned and operated by Placer Dome Inc. The current milling facilities were constructed in two phases with the first being commissioned in 1982. It consists of a grinding, gravity separation, thickening, and leaching circuits. The second phase was commissioned in 1988 with the addition of the CIP, stripping, electrowinning, and carbon regeneration circuits.It is now common practice in the gold processing community to add liquid oxygen to leach circuits to increase both recovery and kinetics. Along with these benefits the metallurgical group at the Dome realized the potential to replace compressed air with liquid oxygen as a source of oxygen for the dissolution of gold. A plant trial of liquid oxygen was undertaken during the fall of 1991. The results of this first test were favourable enough to warrant further investigation, and a second plant trial was conducted in December 1991.The data generated as a result of each trial revealed that oxygen could be economically substituted for compressed air as a source of dissolved 02. The energy savings in required horsepower enabled a rapid payback period. Thus the project was approved in the spring of 1992 and l should be operational during the final quarter of 1992. INTRODUCTIONIn a continuing effort to reduce operating costs and improve recovery at the Dome mill it was decided to investigate the feasibility of adding liquid oxygen (02) to the leach circuit. It is now common practice in the gold processing community to add 02 to the leaching process to increase both kinetics and recovery. It was anticipated that an increase in kinetics would allow us to eliminate one or more leach tanks while maintaining acceptable recoveries. The metallurgical group felt that along with these benefits, the potential was also there to reduce power consumption through the reduction in the processing of compressed air which is quite costly (12 cents/1000 cubic feet per minute in 1991)."

Jan 1, 1993

By Peter A. Bevan

"In massive and semi-massive deposits, it is essential to take samples continuously for specific gravity determination as well as for assays of the various metals of interest. Failure to use specific gravity in mixed deposits of high density contrast will result in incorrect determinations of the average grade.Graphs and linear equations of specific gravity against the grade of one metal are not considered accurate enough in a multi-mineral deposit, but appear to be very satisfactory in a theoretical one-sulphide/gangue mix. Specific gravities based on base-metal values only in massive sulphide deposits will result in underestimating the effect of low grade areas on the average grade and also cause a reduction in the calculated tonnage.IntroductionBy definition, a base-metal assay is the percentage of metal by weight contained in a sample, whether it be a soil or silt sample, a grab, chip or channel sample, or a section of diamond drill core.In those cases where there is a series of contiguous samples, say in diamond-drill core, the average grade may be required of the various assays that are above a desired or required cutoff grade.Internal low grade or waste can be included if the assays one side or the other are used to ""carry"" the lower grade material and the resulting average grade is above the cut-off grade. To determine the average grade, the individual assays are ""weighted"" by multiplying these values by their respective lengths, adding up the cumulative assay times length and dividing by the total length. This method is essentially a weighting by volume, because the core diameter is constant and is common to all the samples being considered for estimating the average grade . If some of the core samples have much higher specific gravities than others, and the specific gravities are not used in the weighting process, the resultant average grade will be over-estimated or underestimated, depending on the grade of the heavier sections. When core assays of approximately the same specific gravity or weight are averaged by length, the error in the weighted estimation of the average grade is negligible."

Jan 1, 1993

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By A. Probst, J. A. Finch

"Solids concentration (% solids) profiles and the clear liquid/slurry interface level (mudline) were determined from conductivity measurements in thickeners at Falconbridge' s Strathcona mill (Ni concentrate and non-mag thickeners) and Kidd Creek Division (Cu, Zn concentrates and final tails in the concentrator and thickeners in the Zn plant).The conductivity measurement system consisted of a probe 1.5 m in length with 24 electrode cells, a 24-channel relay, a conductivity meter and a computer. A conductivity profile is collected which locates the mud-line by the sharp change in conductivity. The conductivity measurements are readily converted to solids concentration profiles without need for calibration.The results from the conductivity measurements were compared with those from pressure profiles and direct measurements on local samples obtained using a modified Noranda sampler.It is concluded that the conductivity technique is applicable to locate the mud-line and to estimate the solids concentration profiles in thickeners. This on-line information could improve the operational efficiency of industrial thickeners.INTRODUCTIONAn automated, on-line technique for detecting the clear liquid/slurry interface (or mudline) and the variation in solids concentration with depth would enhance thickener operation and control. In some processes such enhanced control offers significant benefits. For example, in hydrometallurgical operations solid/liquid separation is often the process limiting step. Water treatment plants are increasingly expected to operate remotely and reliable sensing is vital.Current attempts to detect the mud-line include reflection of some signal (e.g. sonar), floats (Dahlstrom, 1985) and measurement of pressure (Rosenblum, 1991), and in one case, natural radioactivity of the solids (Johnston and Simic, 1991). A recent commercial development uses reflection from a vertical array of optical transmitters/sensors, which also gives local solids concentration (BTG Inc., 1991)."

Jan 1, 1993

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By R. D. Lindsay

Originally the focus of Deak Resources Corporation Business Plan was to establish a method for treating small gold and possibly base metal mineral deposits located in the Kirkland Lake - Noranda area of Northeastern Ontario, Northwestern Quebec at a central treatment facility. Since the establishment of this original business plan in 1988 other processing options have availed themselves for handling the base metal ores off site at a central facility which may preclude their processing at Deak.The site selected for the Deak processing plant was Kerr Addison's Virginiatown operation. At the time this property was acquired from the Receiver following Golden Shield Resources' Bankruptcy in 1989 the mill had been processing in the order of 1, 100 SDT per calendar day through one processing module; a module originally designed to process 1,500 SDT/day of a free milling gold ore. This tonnage level however had not been achieved since 1966 when an average throughput of 1481 SDT per calendar day was recorded.In order to realize Deak's overall Business Plan it would be necessary to expand the mills processing capabilities to provide:(1) A 2200 SOT per day circuit capable of processing a free milling, medium work index gold ore;(2) a 1 ,000 SDT per day flotation and/or cyanidation circuit capable of processing refractory gold bearing materials containing refractory minerals (i.e. copper) that should be removed prior to cyanidation; and possibly(3) a 1200 to 1500 SDT/day base metal circuit capable of processing the broad range of Deaks' Base Metal Property ores. If this circuit were introduced it would be completed in two tonnage phases.Further, it was recognized when operations resumed under Deak in 1990 that the existing tailings dam was suitable for, and had sufficient capacity for additional gold tailings with necessary physical modifications and changes in disposal techniques (including the construction of containment storage cells) that would allow storage for an additional 3.4 million tons of gold ore tailings approximately 1.0 million of which has been deposited since 1990. The focus of Deak's long term tailings disposal strategy is to acquire the Barber Lake Basin which is currently adjoined to our main tailings system which will provide an additional 10 million tons of storage capacity.

Jan 1, 1993

By Christopher Boys

"Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized. These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. In this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dissolving huge cavities in the evaporites. The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds. In at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation.Geological indicators of the proximity of an anomaly may include: a change in insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore wne, and drops in topography > 10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies. Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By Charles J. Zablocki, Robert J. Kamilli

"Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By C. Jay Hodgson, Adrienne C. L. Larocque

The Mobrun VMS deposit in northwestern Quebec does not fit the classic Noranda type model, but exhibits characteristics more consistent with a Mattabi-type deposit. The orebodies are underlain by fragmental volcanic rocks indicative of explosive volcanism in shallow water. Felsic volcanic rocks are more abundant than mafic rocks. Alteration assemblages comprise chlorite, carbonate, sericite, and quartz. Broad semi-conformable alteration occurs high in the footwall to the 1100 lens. Mobrun occurs higher in the stratigraphic sequence than most of the other deposits in the Noranda camp. In this part of the stratigraphy, zones of pervasive carbonatization may be more useful guides for exploration than zones of silicification.

Jan 1, 1993

By Dani J. Alldrick, Alastair J. Sinclair, Colin I. Godwin

"The Stewart mining camp has a long history of precious and base metal mining. The camp is abundantly mineralized, with more than 200 widespread, varied, vein prospects, deposits and orebodies. These show wide variations in the mineralogy of ore, gangue and alteration assemblages, and wide variations in textures and structural settings. This report establishes the timing of the different metallogenic epochs and suggests a specific exploration application for systematic leadisotope analyses.Galena lead isotope ratios from a range of mineral occurrences indicate that all these varied deposits formed during two main mineralizing events. Lead isotope data from the Stewart mining camp do not provide absolute ages for the formation of mineral deposits, but the relative distributions of data are consistent with dates determined in other studies. One ore-forming episode occurred in the Early Jurassic and the other in the Middle Eocene. Both metallogenic epochs were brief, regional-scale phenomena. Some deposits from the younger mineralizing episode were emplacedadjacent to or superimposed on the older deposits.Field and laboratory studies show that the two metallogenic epochs are characterized by different base and precious metal suites: Early Jurassic gold-silver-zinc-lead-copper; and Middle Eocene silver-lead-zinc. Therefore, showings of different ages have different base and precious metal potentials and deserve different exploration emphasis. Lead isotope studies provide a reliable, cost-effective method for evaluating the age and commodity potential of small or recently discovered mineral showings and for setting exploration priorities on properties with several varied mineral occurrences. The determination of the age and metal potential of a prospect at an early stage of exploration may govern the urgency, intensity or even the necessity for further exploration work."

Jan 1, 1993

By A. Zaidi

"The mining and metallurgy industry is highly energy intensive and one of the largest energy users in Canada. Energy costs are also a major component of total production costs in this industry as described in the 1990 Report of The Canadian Industry Program for Energy Conservation (CIPEC). For some plants, energy costs are reported to be up to 30% of total production costs. Therefore, a reduction in energy costs provides an opportunity to improve industry profitability. The specific energy intensity and production costs can be reduced by using modem energy efficient natural gas technologies. In addition, these technologies often improve product quality and increase productivity. Natural gas not only offers economic benefits, but is also environmentally benign as compared to other major energy sources. Emissions of NO"", CO2 particulates and SO2 are lower with natural gas than other fossil fuels.This paper provides a brief overview of some state-of-the-art gas technologies for the mining and metallurgy industry including cogeneration, oxy-air-fuel burners, ceramic immersion tube heaters, direct gas contact process, low NOx burners, and energy efficient liquid heating systems.CogenerationCogeneration is defined as the simultaneous production of electricity or mechanical power and useful process heat from a single fuel source. One of the primary considerations in selecting a cogeneration system is the relative quantities of electrical and thermal energy which are to be produced. Two types of systems are discussed below."

Jan 1, 1993