Search Documents

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By P. V. Golde, R. A. Poole, G. R. Baiden

"The results being presented in this paper are those obtained during 1996 on a drilling automation project at Stobie mine. This project has successfully demonstrated that the remote operation of multiple drills (by a single driller) from surface using Tamrock Data Solo 1000 Sixty drillrigs is technically feasible and can potentially bring significant rewards in terms of productivity and work environment improvements, as well as labour and maintenance savings. BackgroundThe ObjectiveThis paper is an update of a previous report on remote drilling research at Stobie mine. Enabled by the communications system installed at the mine, the ability to remotely control underground equipment from surface has been demonstrated (Poole et al., 1996). This paper discusses the needs and process required to carry this concept to consolidate the operation of multiple machines under a single operator.The TeamThe team assembled to develop and implement the automation and the communi-cations extensions needed to allow the multiple machines’ operation from the surface by one operator included the following:INCO Mines Research supplied the project management and original project initiative. The primary purpose was to prove the advantages of savings associated with the driller not being required to travel to the underground drill location coupled with the savings associated with one-man, multiple-machine techniques.Tamrock EJC supplied the Data Solo 1000 Sixty drills and the Tamrock specific machine-based custom software. The drills were produced in Finland with no provision for remote operation of the drill from other than the umbilical attached local console.Automated Mining Systems supplied the modifications to the drill communications equipment to allow the machine communications to become broadband compatible. As well, Automated Mining Systems also supplied the hardware necessary to be able to remotely control the portable video camera, as well as the data logging equipment.Stobie Mine personnel were made available to test the function and then integrate the concept of remote control drilling into the Stobie operations."

Jan 1, 1997

By Loui Geoffroy, Philippe Gaultier, Martin Piotte, Claude Coache, André Drouin

"Automatic driving at high speed of an underground truck was tested at Brunswick mine in September 1995. Modifications to the truck included: a remote interface to control actuators, front and back video cameras to follow a roof mounted optical guide and proportional hydraulic controls on the steering.The mathematical model of the hydraulic system was adjusted using least square regression. The steering data, used in calculating the regression parameters, were acquired from the moving truck. The automatic steering control used three measured variables: lateral deviation, angular deviation and steering angle. Lateral deviations are obtained using the cameras, which are in continuous view of the guide, while steering angles are acquired from an extensiometer placed at the articulation point of the vehicle. Gain scheduling was used to compensate for vehicle speed and available hydraulic flow. Non-linear characteristics of the modeled hydraulic system were offset using open loop compensation.Speeds up to 23 km/h in forward direction and 13 km/h in reverse were achieved deviaduring continuous testing along one of the mine’s production drifts. Proportional steering was essential in achieving high speeds, as it enabled more precise positioning of the vehicle’s steering direction while reducing the abuses on cylinder and cylinder pins via diminished oscillations about the optical guide at high speeds."

Jan 1, 1997

"Option pricing is used in finance for valuing options to buy (or sell) shares at some future date because it provides a convenient framework for quantifying values subject to uncertainty. As one of the main sources of uncertainty in mining is the price (sales) of the metal, this approach can also be used for valuing mining projects.The first part of this paper reviews options and option pricing; the second part presents the approach developed by Brennan and Schwartz (1985) for using option pricing to value natural resources. Several applications of this methodology have been published; these are described. From a mining point of view, the assumptions made by Brennan and Schwartz are too simplistic. The weaknesses are discussed with a view to improving an apparently promising new way of assessing the value of projects. IntroductionThe collapse of the British merchant banking group, Barings, has highlighted the risks that can be incurred by speculators and arbitragers in the futures and options markets. But this negative attention on futures and options should not make us forget their positive aspects. They can provide producers and consumers of metals with more predictable sales prices. The introduction of the new traded average price options, TAPOS, by the London Metal Exchange in January 1997 is a response to this need. Equally important, the theory that the finance industry has developed for valuing options provides an interesting framework for valuing mineral projects as well. While this paper was being revised, the South African gold mining house, JCI, announced that it was using a methodology based on option pricing for valuing the mineral rights to deeplevel gold resources (see Box 1)."

Jan 1, 1997

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

By Orlando C. Gaspar

Abstract - The presence of fine-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sulfide ores. The beneficiation of most massive sulfide ores from the Iberian Pyrite Belt requires extremely fine grinding to liberation sizes of K80 = 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning patterns has shown that the different ore types are distributed as ore lenses within the massive sulfides. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the efficiency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types defined at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sulfide ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By A. Aftabi

Abstract-To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2 at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1 ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples are anomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb (>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2 in the southern part of the area. The strong Cu- Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry copper mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sulfide mineralization is present.

Jan 1, 1997

By J. B. C. Wu, B. McKee

"Mining along with subsequent processing of the minerals often presents conditions where a wear- and/or corrosion-resistant alloy is needed to minimize downtime and maximize efficiency. This paper is intended to give an overview of the alloys that are currently being used, as well as those developed in recent years that could be used in the mining industry. Emphasis will be put on the iron-, nickel-,cobalt-based alloys and composites containing a variety of carbides. The characteristics, properties, product forms, and methods of application are presented. In addition, examples of the actual use of these wear-resistant materials are illustrated.IntroductionPreventing wear and corrosion is important in any industrial operations. In the mining industry, the process equipment typically suffers many different types of material degradation. Abrasion, impact, erosion, metal-to-metal wear and corrosion are typically encountered. Each situation requires different material characteristics to retard the degradation process. Therefore, it is essential to understand the characteristics of the materials and the effects of the alloying elements.There are four common classes of metallic materials for resisting wear and corrosion; namely, iron-based alloys, nickel-based alloys, cobalt-based alloys, and carbide-containing composites. Each class of material has its own characteristics. Depending on the chemical composition, the materials within each class can be vastly different in properties. In recent years, there have been materials developed in each of the four classes using the knowledge of the metallurgical principles and the effects of the alloying elements on the material degradation process.To use a wear-resistant alloy, it is also necessary to understand the available product forms and their application methods. Weld overlaying is a traditional way of using these alloys (Wu and Redman, 1994). In recent years, thermal spray is becoming popular. For applications where over-laying and spraying are impractical, solid components can be made by a variety of casting and powder metallurgy techniques. They can also be fabricated from the wrought products.To select a proper material for an application, it is important to understand not only the characteristics of the wear-resistant materials but also the degradation process. Due to the complexity of the processing environments, past experience is also helpful in making the decision on the material selection."

Jan 1, 1997

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By Malcolm Scoble, Nick Vagenas, Greg Baiden

Recent advances in underground communications technology have demonstrated the feasibility of teleoperation and automation in underground metal mines. One major challenge lies in the automation of underground mobile machines from surface, with the potential to reduce significantly the need for human involvement in underground operations. This paper reviews the evolution of underground metal mining automation, principally related to the development of teleoperation and automation of mobile mining machines. Examples of prototype systems are given and the associated benefits that have been observed are reviewed.

Jan 1, 1997

By R. W. Lawrence

"The management of acid rock drainage( ARD) to prevent impact when tailings are disposed of in the environment requires understanding of the phenomena giving rise to acidic drainage, a rigorous evaluation of the weathering characteristics of the tailings, and the successful implementation of control measures that will be effective in the long term. This paper provides a brief theoretical background to the complex reactions taking place in mill tailings containing residual sulfide minerals which must be appreciated to enable waste characterization program to be effective in predicting the future behavior of the tailings and in designing control methods which will work. The principals and practice of prediction and control as part of an ARD management strategy will then be discussed.Paper Not Available at Time of Publication"

Jan 1, 1997

By Daniel J. Schulze

Abstract-Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesiochromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (specifically elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnets in exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2 contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Crpyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997

By Andre L. De Vegt, Cees J. N. Buisman

"For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps:1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates.2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur.Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S02) can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.lntroductionSulfur can be present in various water and gaseous streams in a mining operation. In many cases the sulfur compounds have to be removed because of toxicity, corrosive properties and contribution to acid rain. Mine waters can contain dissolved heavy metals. An efficient way to remove dissolved metals removal is the precipitation as metal sulfides. Paques has developed and installed treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. These treatment systems biologically convert sulfate to hydrogen sulfide (H2S) which can be used in heavy metal precipitation. Excess H2S is biologically converted to elemental sulfur. This paper provides an overview of these newly developed biotechnological treatment systems."

Jan 1, 1997

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By Lawrence Devon Smith

"What is Due Diligence?Within the mining industry the term “due diligence” is used to describe a detailed data review, generally in connection with the purchase or sale of a mineral property, the approval of a large capital expenditure, or the borrowing of a large sum of money.The term originates in the requirement of the board of directors of a corporation to “act honestly and in good faith ... and exercise the care, diligence, and skill that a reasonably prudent person would exercise in comparable circumstances” (OBCA, 1994). Furthermore, the law assumes that a corporation (or its board) will have exercised due diligence in the acquisition of an asset and, therefore, knowingly (in the absence of fraud or deceit) will have taken on the liabilities and obligations associated with the asset (Nelson, 1994). This is the familiar “Buyer Beware”.Directors are liable for their decisions except “if the director relies in good faith upon financial statements of the corporation represented … by an officer of the corporation or in a written report of the auditor, or a report of a lawyer, accountant, engineer, appraiser, or other person whose profession lends credibility to a statement made by any such person.” (OBCA, 1994).Hence the importance of reports prepared by professionals. They provide confirmation that the directors have exercised due diligence in the performance of their duties. For this reason these reports are referred to as due diligence studies"

Jan 1, 1997

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997