Search Documents

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By M. W. Grabinsky, P. B. Tomory, J. Carvalho, J. H. Curran

Many underground mining operations use Split Set friction stabilizer bolts for rock support. Currently, however, little has been done to quantify the effects of various rock mechanics and operational parameters on the capacity of frictional support systems. The strength of Split Sets is usually measured by means of a pull test wherein a jacking force is applied to the bolt and a slip load is obtained. In order to evolve a rational design procedure for this type of support, an extensive database of over 900 pull test results from more than 50 mines through- out North America has been assembled and analyzed. Associated relevant rock mechanics parameters (rock type and quality) and operational details (drilling method, bit size, drive time, time to pull test) were also obtained, as completely as possible, for each test. Analysis of the information has yielded several charts that relate pull-out strength to relevant parameters and simple statistical analyses were conducted where necessary. Quantified distributions for pull-out strength were also produced for several operating conditions. The factors that most significantly affect bolt strength have been identified and specific applications to design are discussed. The information presented will assist mining engineers in designing safer and more economic support using Split Sets.

Jan 1, 1998

By L. K. Daneshmend

The mine of the year 2020 will need to be based on a new way of mining. It will employ technology in a paradigm that assumes responsibility for sustainable development: taking account not only economic but also ecological and social issues. This will require a holistic approach to mine design and planning, considering all controlling factors and impacts (technical, economic, environmental and social). A national collaborative strategy is required to address the several options that exist for the development and application of 2020 mining technology. Key issues in implementing 2020 mining technology will also relate to human resources, in terms of employment, skills and education. A need exists to proactively prepare for 2020 through development of a comprehensive education and training strategy.

Jan 1, 1998

By D. G. Brophey, J. A. O’Neill

"High costs, both in terms of human resources and financial costs, have long been the end result of accidents involving vehicles which continue to occur too often throughout our industry.For example, radio remote control LHDs too often seriously injure their operators in underground operations. Costly efforts are required by mine owners to provide safety bays and platforms from which their operators can work safely. In open pit operations, large heavy haulers have too frequently backed over vehicles or turned into vehicles unfortunate enough to be situated in their large blind spots. These are just two examples of situations that have occurred again and again under similar circumstances.Meanwhile, electronic methods of detecting proximity to vehicles have continued to develop. The time has come for the industry to think “outside the box” to evaluate whether many of these new methods can solve these recurring problems.This note takes a look at various types of proximity detection technologies that are in use today in other industries, and discusses the various potential applications within our industry."

Jan 1, 1998

By J. A. Finch

In this paper, the author offers a personal view of what the next 30 years holds for mineral processing. Restating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining ?mineral processing ?extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro- and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but this author anticipates that the new lines will come from the waste management business. The paper concludes with the examination of the “research cycle” and identification of growth in small “high tech” companies and university research centres

Jan 1, 1998

By A. Coulombe

"RésuméL’analyse des séquences d’exploitation, actuellement en usage pour les gisements très inclinés, a démontré qu’elles ne sont pas toujours optimales du point de vue du contrôle des terrains et de la concentration des travaux d’abattage (nombre de chantiers simultanément en opération). Effectivement plusieurs séquences sont très propices à la création des nombreuses zones de hautes contraintes, qui sont à l’origine des effets de pilier. L’étude de cas de la mine Lac Shortt a démontré que certaines séquences d’exploitation, actuellement en usage, ne sont surtout pas adéquates dans le cas d’un état élevé des contraintes naturelles. En effet la mine a eu de sérieuses problèmes avec le contrôle des terrains (coups de terrains et les effondrements des épontes). Ces effondrements étaient responsables de la dilution excessive et des pertes importantes des réserves minières. Les deux nouvelles séquences proposées, visent la meilleure redistribution des contraintes d’exploitation en vue d’éliminer la création des effets de pilier. En plus elles permettent une concentration plus élevée des travaux d’abattage.À notre avis les séquences proposées pourraient améliorer substantiellement la stabilité des chantiers d’abattage et par la suite les performances technique et économique des opérations souterraines. ABSTRACTThe planning of underground mining sequences represents an important aspect of the mining operation. The analysis of mining sequences actually in use for very steep orebodies has demonstrated that they are not always optimal, considering ground control and the number of stopes simultaneously in extraction. These sequences are conducive to the creation in the rockmass of several stressed zones caused by pillar effects. The case study of Lac Shortt mine showed that the sequences of exploitation currently in use are not adequate especially in the case of a high state of the natural constraints. Indeed, the mine had serious problems with ground control (rock bursts and collapse of walls). These collapses were responsible for excessive dilution and significant losses of mining reserves. The two new sequences suggested aim for the best redistribution of exploitation constraints in order to eliminate creation of pillar effects. Moreover, they allow a higher number of stopes to be extracted simultaneously. In the opinion of the authors, the sequences suggested could substantially improve the stability of working areas and, thereafter, technical and economical performances of the underground operations."

Jan 1, 1998

By C. Sui, J. E. Nesset, M. Li, J. Y. Kim, S. L. Chryssoulis

"A plant study of zinc rougher flotation at Brunswick Mining was conducted using lime, soda ash and a combination of both as the pH modifiers in order to establish the effects on sphalerite and pyrite kinetics and mineral selectivity. The plant sampling and analysis was augmented by surface analysis using TOF-LIMS, SEM and XPS as well as fundamental precipitation and surface-charge studies in the sphalerite Ca/C03/S04 system.The results revealed the important role of carbonate ions in cleaning the sphalerite surface for effective activation by CuS04 to occur, and the beneficial role of combined soda ash and lime in increasing pyrite and galena depression.1.0 IntroductionThe studies reported in this paper were initiated as part of an investigation into the causes of a particularly pronounced seasonal deterioration in metallurgical performance at the Brunswick Mining concentrator during the summer of 1995. The concentrator treats a complex base metal ore having a typical feed composition of 9.0% Zn, 3.5% Pb, 0.4% Cu and 100g/t Ag at a current throughput of 9,000 TPD, although at the time of the problem in 1995, the average production rate was closer to 10,500 TPD. Zinc, lead, copper and bulk (zinc-lead) concentrates are produced with overall metal recoveries of 86% zinc, 63% lead, 60% copper and 60% silver; results which are typical of the lower recoveries associated with fine-grained, highly complex VMS and SEDEX type deposits. The main economic minerals of interest are an iron-containing (7% Fe) sphalerite, galena and chalcopyrite with the main diluent (about 60% wt) being pyrite.Figure 1 shows a simplified flowsheet of the Brunswick milling circuit while the seasonal decrease in summer metallurgy in 1995 is illustrated in Figure 2. Of significance is the rapid drop in copper and lead recovery in June while there is an apparent delay until late August-September before the zinc deterioration reaches its lowest point. A more typical seasonal effect within the experience of the authors is the reverse of the Brunswick situation, namely an improvement in summer performance thought to be associated with improved differential flotation kinetics during warmer weather leading to better mineral selectivity. The historical Brunswick experience was particularly severe during the summer of 1995 with estimated incremental losses of $10 Million for this period. The potential of the very significant economic benefits to be gained from understanding and hopefully improving the annual drop in performance led to an investigation involving the minesite metallurgical group, the Noranda Technology Centre (NTC) as well as researchers in Professor Jim Finch's group at McGill and the surface analytical services and interpretive skills of AMTEL."

Jan 1, 1998

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

By G. D. Mcdowell, L. B. Cochrane, B. D. Thompson

"Abstract - Exploration for deep underground copper and nickel sulfide deposits in the Sudbury mining camp is carried out with surface drilling. More detailed drilling, with an advanced underground exploration program, may be necessary to establish an accurate interpretation of the deposit geology and upgrade the resource estimate to the measured category for reserve estimation and feasibility assessment. Resource evaluation is a lengthy and costly process that could result in a decision not to proceed with the project. For projects that proceed to production, significant reductions in the operating and capital costs could be achieved with a more accurate interpretative model of the deposit geology and mineralization. Quality control procedures to ensure the integrity of the drilling data and interpretation guidelines are essential steps in the development of a deposit model. The use of block modeling techniques and the application of geostatistics for resource estimation further improve the quality of the resource model.Significant improvements to the interpretive models can also be achieved by incorporating additional information from geophysical measurements to validate and constrain the geological interpretation. The geophysical models must be consistent with known geological environments and oreforming processes, which has required the concurrent development of comparative models from exploited deposits. These geophysical techniques can also provide key geotechnical information required for the optimum design of the mining method and mining sequence. The objective of this program is to improve the accuracy of the deposit model and the quality of the resource and reserve estimates in order to optimize capital investments and reduce the development and operating costs of underground mining projects. Several of these techniques are currently being tested at INCO Limited’s Sudbury operations. The results from those tests are presented and their applications are discussed within the framework of resource/reserve classification systems and project evaluation objectives."

Jan 1, 1998

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By R. S. Rogers

Abstract - Forensic geology in a mineral exploration context is concerned with geology and related technical matters as they pertain to legal cases involving exploration and evaluation of mineral properties. Such cases involve the possibility of outright scams that include falsification of data and information, as well as inappropriate application of various technical procedures. Experience in forensic geology in such cases emphasizes the need for systematic quality control procedures during routine exploration/appraisal and indicates the need for more attention to ‘target hardening’ (improving security in the chain of custody of samples and assay results). A number of ‘early warning signs’ that might suggest some form of tampering or falsification of information are listed. These measures will support the work of the "Qualified Persons" (geologists and engineers) entrusted with the scientific and technical aspects of mineral exploration, and facilitate the increased attention to regulatory oversight and enforcement of securities laws recommended in the report "Setting New Standards."

Jan 1, 1998

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By A. Probst, N. Moores, J. A. Finch

"In 1994 McGill and INCO (Sudbury operation) initiated transfer of technology originally developed to detect level in flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud-line and solids load. The probe consisted in a vertical tube with 32 equally-spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth (so-called conductivity profile) from which the mud line and % solids could be inferred. The probe was installed in October 1994 and has been successfully detecting profiles since then. This communication includes a description of incidents and experiences during this technology transfer process including: probe installation and start-up; software modifications to accommodate operating conditions and operators' needs; calibration procedures to adjust to changes in performance as a consequence of long term use; and preliminary observations on the last stage, still in progress, signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.IntroductionThickening is one of the basic unit operations in mineral processing and hydrometallurgy used to separate suspended solid particles from a solid-liquid dispersion by gravity settling. As the dispersion enters the thickener, the solids settle and clarified water overflows the top. A thickener, which may be continuous or batch, is basically a large vertical cylindrical tank provided with devices to feed the dispersion and to remove the settled solids. The tank provides residence time for the particles to settle. The dispersion enters the thickener through the feedwell whose function is to dissipate the momentum of the feed stream and to create relatively quiescent conditions around the entering point. Rotating rake arms move the settled solids towards the discharge point located at the bottom centre of the tank.There are normally three distinct zones in a thickener: a top layer of clear water, a middle layer called a sedimenting zone in which particles are settling, and a bottom layer called a compression zone in which particles are pressed together as a consequence of the weight of accumulated particles. Proper operation of a thickener requires two simultaneous conditions: no solids in the water overflowing the top and the target solids content in the underflow pulp. To achieve these conditions is difficult because sensors for detecting the sediment line (interface between clear water and sedimenting zone) and the solids content in the compression zone are not commercially available."

Jan 1, 1998

Abstract-This paper discusses the fundamental question, "what is an adequate sample size?" in the light of recent developments regarding parameters of Gy’s well-known formula for predicting sampling variance. New understanding of the granulometric factor, g, and the liberation factor, l, had significant impact on the results of calculations involving Gy’s equation. For the granulometric factor, justifications are given as to why nominal comminution size should always be reported as P95 (i.e., the screen size rejecting 95% of the mass). A small but important change in the model to estimate the liberation factor makes the difference between a predictive formula that works or does not. Other parameters and considerations regarding their practical implementation are commented upon in light of the author’s experience.

Jan 1, 1998

By J. Ling, J. Xiao, A. R. Laplante

"The most challenging gold gravity separations occur when gangue has a high s.g., gold is fine, or a combination thereof This paper examines such separations, and evaluates the performance of a 3-in Knelson Concentrator at various rotation speeds, a 4-in SuperBowl, and a laboratory Mozley Multi-Gravity Separator (MGS). Synthetic feeds, primary cyclone underflows and flash flotation concentrates are tested.It is concluded that higher rotation speed are mostly useful for very fine (< 3 7 µm) gold recovery, with potential loss of recovery in the 37-212 µm range. This problem is traced to the collapse of the flowing film at higher Gs, which hinders the percolation of particles of intermediate size. Increasing fluidization water flow can alleviate this problem, but the recovery of very fine particle then drops. The MGS does not operate with the same principles, and can achieve good to very good recoveries of very fine to fine gold particles, but the unit has a high cost to capacity ratio, and there is no evidence yet that it can yield smeltable concentrate grade or a concentrate that can be upgraded with a shaking table.IntroductionThis presentation is a sequel to similar CMP presentations of the past eight years; all focused on practical aspects of gold recovery. The first hard rock application of the Knelson Concentrator (Laplante et al, 1990), studies of the grinding and classification behaviour of gold and other malleable metals (Banisi et al, 1991; Laplante et al, 1995), the development of a 3-in Knelson based methodology to study gold gravity circuits (Laplante and Shu, 1992), a comparison of the Knelson and Falcon (Laplante, Laplante et al, 1993), the presentation of a test to determine the amount of gravity recoverable gold, or GRG (Laplante et al, 1996), and the use of synthetic materials, in particular tungsten, to mimic gold (Laplante et al, 1995) were presented. A summary of many practical implication of the McGill research was presented in 1994 (Laplante). Whereas gold gravity recovery was less popular and largely jig-based (in North America) at the beginning of the eighties, many gold plants now incorporate a gravity circuit, and the Knelson Concentrator is the most commonly used unit."

Jan 1, 1998

By P. V. Golde, R. A. Poole, G. R. Baiden

"INCO is committed to proceed into the next century using automation and robotics to achieve safety and productivity goals necessary to enhance its competitive position. Stobie Mine, decades old, is the first of its mines to change from labour-intensive to automationassisted techniques. This paper is a synopsis of the progress made during the transition period including overviews of some of the projects as well as some of the difficulties in the assimilation of the technology. BackgroundThe ObjectiveThis paper is an update on remote control and LHD automation installation at Stobie mine. The communications system installed at the mine and the ability to remotely control underground equipment from surface is reviewed (Poole et al., 1996, 1997). It discusses some of the experiences and processes required to further the concept to consolidate the operation of multiple machines under a single operator. It considers the communications systems requirements and their focuses, particularly on the development of systems for the tele-operation of LHDs and drilling machines from surface."

Jan 1, 1998