Search Documents

By Mohsen Amir-Rahmat

The ore of Sarcheshmeh copper deposit that has been located in the south ?east of Iran, contains four type of rock that they have their specific hardness and strength according to their alteration type and mineralization. Blasting of these various types of mine rocks prepares various types of size for the product of mine as the feed of concentration. Along the crushing of this feed a few factors effect on the efficiency of the crushing unit. The aim of this project has been the consideration of the effect of ore size on the efficiency of crushing unit. For this investigation along the year 2000 A.D., six sample from feed and six sample from product of crushing unit have been prepared. The results of the screen analyze of these samples has shown that the size of feed has been lesser than the primary plan and the size rate of the product has been bigger than the primary plan. Also in this research the effect of feed size on the quality of product size has been considered.

May 1, 2003

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By Mike Power

Geophysical techniques have played a pivotal role in northern kimberlite exploration since the initial discovery at Point Lake in 1991. In the Slave Craton and surrounding regions, there are definite contrasts in physical properties between kimberlite intrusions and surrounding bedrock. Kimberlite commonly displays higher magnetic susceptibility, distinctive remnant magnetism, low electrical resistivity and lower density than surrounding rocks. In addition, the distinctive geometry of kimberlite pipes is reflected in geophysical responses which further facilitates target discrimination. There has been an evolution in geophysical exploration strategies over the past 12 years. Helicopter total magnetic field and electromagnetic (HEM) surveys have proven to the most cost-effective means of conducting first pass investigations in prospective areas. During the early 1990's, total magnetic field and frequency domain electromagnetic surveys were virtually the sole techniques employed during follow-up surveys. Inevitably, the initially high rates of kimberlite discovery declined in the areas surrounding the original finds. Marginal magnetic and EM anomalies were all that remained to be tested and this spurred interest in the improvement of existing interpretation algorithms and in the application of additional complementary techniques to reduce the exploration risk. Gravity has become a popular third survey following the deployment of the Falcon (TM) airborne gravity gradiometer system by BHP Billiton in 1999 and improvements in ground techniques. Ground penetrating radar (GPR) has proven to be particularly useful in delineating kimberlite pipes following drill discovery and in exploring for kimberlite dykes in settings where indicator mineral trains indicate such targets are likely. Seismic methods have been tested for both reconnaissance and delineation but remain underemployed. Given the high cost of drilling in the North and the proven success of geophysical techniques in reducing exploration risk, it is likely that an increasingly diverse range of geophysical techniques and innovative interpretation techniques will continue to be applied in kimberlite exploration.

May 1, 2003

By Greg Yuriy

This paper discusses research carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in the field of discrete-event simulation of mine equipment systems and reliability assessment of these machinery using genetic algorithms. The AutoMod simulation package, from Brooks-PRI Automation Inc., is used in this research. It is a 3-D discrete-event simulation/animation software tool for creating realistic depictions of manufacturing and materials handling systems. Discrete-event simulation involves modeling of real-life systems based on variables and events which occur or change at distinct points in time. In our case, a two level, multi-drift sublevel stoping model was created in AutoMod for the simulation of the equipment fleet employed in the development cycle (drilling, explosives loading, blasting, materials hauling, ground support) of a typical underground mine in the nickel mining region of Sudbury in Ontario, Canada. The equipment primarily considered in the simulation is Load-Haul-Dump (LHD) vehicles (scooptrams), drills, explosives-loaders and roof bolters. The purpose of the simulation study is to assess the impact of equipment failures to mine?s production throughput. In more detail, using Mean Time Between Failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity. This paper will indicate the significance of equipment failures to a mine?s production and suggest a methodology based on the combination of discrete-event simulation and a predictive reliability assessment model using genetic algorithms for the study and analysis of mine equipment systems.

May 1, 2003

By David Penswick

Despite anecdotal evidence to the contrary, the mining industry is not in decline. Rather, the world?s largest mining companies are among the most consistently profitable companies in any industry. In many cases, profitable mining companies have been built around a few large scale, long life mines. These criteria for success ? size and long life ? have led to the current preference for deposits that can be exploited using open pit methods. However, developments in the science of block caving have resulted in this mining method achieving costs and productivities that are competitive with the largest open pits, while achieving widespread applicability. One implication of the low costs and widespread applicability of block caving is that some current open pits are possibly too deep.

May 1, 2003

By Jerry Danni

In order to remain viable today, corporations must view the environment as a strategic issue, and integrate environmental management throughout the organization. Corporate programs that used to be based primarily on regulatory compliance now must emphasize strategic environmental management systems, and must integrate these environmental systems with basic business functions. The mining industry today is global, and must have an organizational structure that can embrace different cultures, physical settings, and regulatory regimes. Sound environmental management practices are not different from good management principles. An effective environmental management system should be a complementary system to an organization?s overall management framework, integrated and aligned with the existing management structure. Integrating environmental management into core business functions is just good business. An effective environmental management system is a critical component of a company?s commitment to environmental, social and economic accountability. This paper presents the elements of the Kinross Gold Corporation strategic environmental management system and discusses the integration of the environmental management system into the core business functions throughout the Company

May 1, 2003

By Joe Price

Canada?s energy future will increasingly depend on a supply of light, sweet crude oil derived from the Athabasca oil sands deposit of North-eastern Alberta. Billions of dollars are being spent on the construction of new and expanded mine and bitumen extraction plants, in situ recovery facilities, pipelines, upgrading installations and all the infrastructure needed to support these projects. The success of the existing operators has also inspired new players, anxious for ?a piece of the action? to come forward with exciting project proposals of their own. None of this investment and spin-off economic activity would be taking place today if events had unfolded differently in this part of the world some one hundred million years ago. The accumulation of sand in rivers, estuaries and in the near-shore marine environment created the great reservoirs that host the enormous oil deposits these projects are designed to exploit. Mine operators of all stripes will likely agree that there are few good ?geological surprises?. With specific reference to oil sand deposits, the geological history determines the distribution of sand, silt and clay bodies, which in turn controls the ore grade. Important design factors including everything from stable pit slope angles to tailings properties reflects events that took place millions of years before. An understanding of the sequence of events that resulted in deposition and preservation of the sediment and oil are important to sound design for both mining and in situ facilities. A geological history of the region is described. Site-specific examples from Syncrude?s operating mines are used to illustrate some of the geological factors that can present design challenges.

May 1, 2003

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By S. Goodman

Successful exploration for and exploitation of a mineral deposit requires an accurate understanding of the deposit architecture in 3D, and of the development of the mineralizing system through time, which requires a thorough comprehension of the structural framework of the deposit. The integration of geological, geophysical and geochemical datasets to arrive at a 4D structural framework is well-established and has been successfully applied by SRK Consulting in projects from deposit to regional scale. In some cases, we can go beyond this, applying the SEEBASETM technique, which utilizes a ?bottom-up? approach to basin analysis. SRK?s approach primarily relies on the interpretation of magnetic and gravity data, calibrated with many other datasets including mapped geology, topography, event histories, wells/drillholes and seismic data. The SEEBASETM model is a culmination of this data integration and is produced through an iterative process of structural interpretation and geophysical modeling, where an interpretation of basement composition and 4D structure is used to constrain depth-to-basement geophysical modeling, and the modeled depths are then used in conjunction with the structural interpretation to constrain contouring of the basement topography. The result is a rigorously calibrated, 3D view of the basement surface, which can be used to understand the basement and basin architecture, and thus serves as a predictive exploration model. This technique, which was developed for use in the petroleum industry, is now finding success as a predictive tool in mineral exploration.

May 1, 2003

By Bruno Bussière

Acid Mine Drainage (AMD) from mine wastes is one of the most environmental challenge currently facing the mining industry. AMD is the result of the natural oxidation of sulphides exposed to air and water. When mining wastes have the potential to produce AMD, these reactive wastes have to be managed to meet existing environmental regulations. The LTA site (property of Barrick Gold Corp.) contains sulphide tailings that have the potential to generate AMD. The closure option Barrick selected was to construct a multilayered cover with capillary barrier effects (CCBE). The main objective of this CCBE is to prevent the production of Acid Mine Drainage (AMD) from the tailings stack covering an area of approximately 60 ha. Since its construction in 1996, the cover has been monitored to evaluate its performance. Two of the measured parameters are volumetric water content and matrix suction. This paper presents some of the main results from the monitoring program that started seven years ago. The results show that the cover is largely able to maintain a high degree of saturation (greater than 85%) in the moisture-retaining layer. The actual performance of the CCBE on the flat surface of the 60 ha site is even better than expected at the design stage. The area that requires more specific attention with the LTA cover is the influence of slopes that can reduce the performance of the CCBE during dry periods. However, these effects seems to be local and do not significantly affect the overall performance of the CCBE to mitigate the production of AMD at the LTA site.

May 1, 2003

By Ross Dimmock

The productivity of a mine has the same goals as the quest to complete a tunnel project both safely and within time. A key aspect to achieving this goal is to excavate and support the working face as quickly as possible, allowing early re-entry to start construction of the next advance in safety. As with tunnels, the use of high performance wet-mix sprayed concrete has increased in mines dramatically over the last few years, and year on year has seen a stepwise increase in shotcrete performance, particularly in the first few hours. Shotcrete early age strength development clearly offers mining teams enormous advantages by allowing early, safe re-entry to the face. This paper illustrates that in the hard rock tunnelling field, modern shotcrete approaches do not cause delays in re-entry, but allow a continuous construction cycle. Furthermore, the paper identifies the most suitable, up-to-date shotcrete admixture and equipment technology available to the mining community to permit early re-entry.

May 1, 2003

By Paul Harvey

Following initial discovery in 1991, BHP Billiton Diamonds Inc opened Canada?s first diamond mine, the Ekati Diamond Mine TM (Ekati) in the Northwest Territories on October 14th, 1998. Four short years later on November 29th, 2002, saw the opening of North America?s first underground diamond mine - the Koala North mine. Nestled between the original Panda open pit and the new Koala pit which is in the early stages of production, Koala North represents the only underground kimberlite mining venture in arctic conditions outside the new underground mines being developed by ALROSA in the Yakutsk region of eastern Russia. Extensive underground kimberlite mining has been practiced in the Republic of South Africa for much of the 20th century and continues today. Underground mining represents a key component of the long term business plan for the Ekati. As various open pits reach their economic limit, continued recovery of high value ore at depth is dependent upon the ability to productively mine the kimberlite pipes by underground methods. As a function of its location, size, and value, the Koala North pipe is ideally positioned to host the first underground mine at Ekati . In addition to being a production source for the operation, Koala North is designed as a learning mine, from which to gain valuable experience in preparation for the potential mining of other larger, higher value pipes by underground methods in the future. Fortuitously Koala North was available for development so the learnings could be integrated into the Panda mine design prior to completion of the Panda pit. Establishing our first underground diamond mine, and applying the open benching mining method in arctic conditions brings a unique combination of mining challenges together in a harsh climate and remote environment. This paper examines the design and establishment of the Koala North mine. Discussion includes experiences gained from the first year of development, production start-up, and provides a brief overview of our potential underground future at Ekati .

May 1, 2003

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

By Marcel M. Djivre

The paper will outline historically the different materials used for pouring sockets and illustrate the current trend due to inherent advantages. A section will be devoted to engineering stress analysis showing the criteria necessary for the wires not to slip inside the poured socket material. The Ontario Mining Regulations pertaining to poured sockets will be reviewed with emphasis on the acceptable type of sockets depending on usage. In addition the paper will review the proper socket preparation techniques and explain the destructive testing conducted at the Materials Testing Lab essential for the certification requirements. In conclusion the paper will show the importance of the Certification Program for the safety of Miners working in Ontario, Canada and the World. The paper is also intended to inform the Mine Operators and Consultants that to-date the .Wirelock. sockets have been used safely for hoist ropes of locked coil and non-rotating construction and for the termination of balance ropes, and that further research is required on the construction of a socket approved for rotating type mine hoist ropes.

May 1, 2003

By Lihong

A series of Fe2O3-elimination experiments were conducted on feldspar samples from Tangshan Stone?powder Plant. These experimental methods include scrubbing desliming, flotation,rod milling and high gradient magnetic separation. Some technical factors of feldspar concentration and a new technological flow?sheet of ceramics raw material concentration were put forward.

May 1, 2003

The following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results. In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results. Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results. The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is: ??Uniform within the diamond exploration industry; ??Consistent with reporting from other industry sectors; ??Comprehensive; ??Unambiguous. The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation. The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation).

May 1, 2003

By Christoph Mueller

?Globalization and the impact on mine operations? is one of the themes of the 2003 annual CIM meeting. Global mining business in practice always means to act with local base material resources in order to reach the mining company?s global business goals. On the other hand these operations are characterized by cost pressure and cycling product prices. Driven by actual prices, local product markets and local production cost, one time one mine can be most efficient while under different circumstances another mine will be the most efficient producer for the same customer [PENSWICK, 2001]. Therefor in the future the most profitable mining companies will be those who have permanent ?real-time? control on their actual production cost level. Certain approaches are under way to provide reliable modeling tools for aiding mining companies in highly complex decision finding procedures. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory? [WIGDÉN, 2001]. Crucial to all these activities is the ability of getting reliable, just-in-time information from the entire mining production chain. As modern mining machinery today is controlled electronically and even already operated autonomously, the theoretical preconditions for the data acquisition is already fulfilled. But up to now, there was no way of cost effectively exchanging the process information with databases, simulation tools and other enterprise level software. Any data exchange problem had to be solved by individual and expensive software development projects. To solve these problems, the International Rock Excavation Data Exchange Standard (IREDES) was launched in 2000 by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. The standard?s technical architecture is flexible and open - also for future applications. It uses modern technology enabling easy data exchange with commercial databases as well as open on line networking.

May 1, 2003

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By Niklas Frank

Ore and waste transports form an integral part of any mining operation and represents a substantial portion of the mine´s total operating cost. Mine layout, truck fleet and size, production rates, haulage distances, shift schedules, maintenance strategies etc. are all important and not at all static variables. They all change during the life of a mine and interact in a dynamic way. It is therefore essential for the successful mine management to constantly analyse and optimise the mine's transport systems. Önnerlöv has recently conducted a life-of-mine haulage simulation project for Zinkgruvan Mining, a medium sized, underground zinc producer, located approximately 60 kilometers south of Örebro, Sweden. The main objective of the project was to analyse and optimise the investments required to provide ore and waste haulage under changing conditions over an +10- years period: Deepening of the mine, increased production rates, changed mine layout, changed truck fleet etc. A large number of scenarios has been tested in the simulation model in order to identify the "lowest cost per ton" solution. This paper comprises an introduction of Zinkgruvan Mining and a brief background to the actual project, a description of the simulation model, project conclusions and some useful hands-on tips for mining engineers and project managers how to run a successful simulation project.

May 1, 2003