Search Documents

By L. Bichler, C. J. Verdon

In this work, the effect of doping yttria stabilized zirconia (YSZ) with 5, 10 and 15 mol% erbium oxide (Er2O3, erbia) was investigated using spark plasma sintering (SPS) technique. Sintering was carried out at 1300°C with 30 and 60MPa uniaxial pressures and a 5min hold time. Densification kinetics were studied using displacement response from the SPS machine. As-sintered microstructure characterization was carried out via scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques, while chemical composition was characterized by energy dispersive X-ray spectroscopy (EDS). The results suggest that sintering carried out at 60MPa produced high density composites even though erbia dopants were found to inhibit material densification and grain growth during sintering. 5, 10 and 15mol% erbia- YSZ had cubic crystal structures, as verified by XRD analysis.

Jan 1, 2014

By N. H. Grace

"IntroductionDURING the past half century, the economy of Western Canada was largely centred on agriculture. However, the impact of World War II has led to an acceleration in the development of a variety of natural resources so that, today, Western Canada is experiencing great industrial development. Consequently, the availability •of low-cost energy assumes prime importance. In the final analysis, industrial growth and expansion are intimately linked to the energy resources.Coal ReservesHas Western Canada adequate coal reserves to meet the present accelerating demand for power in the days that lie ahead? This question must be answered before detailed consideration can be given to the probable patterns •by which various energy sources in Western Canada may be expected to meet the expanding demand. Figure 1 indicates the extent and distribution of the Canadian coal reserves, the data having been prepared by Dr. B. R. MacKay for the Royal Commission on Coal in 1946 (1). The amount of readily recoverable coal is listed as one-half the quantities shown on the chart. It is interesting-to note that upwards of 90 per cent •of the Canadian coal reserves .are located in the three most westerly Canadian provinces. It has been estimated that the coal reserves, at the present rate of mining, would be adequate for about 3,000 years. Consequently, it may be concluded that the coal •reserves in Western Canada •are indeed adequate to meet tremendous energy demands for many centuries. When the oil and natural gas have been exhausted, the great coal reserves will still be available."

Jan 1, 1953

By M. Nusheh, C. Bumby, A-H. Puichaud

"Vanadium-bearing titanomagnetite ironsand deposits occur along a 480 km stretch of the west coast of New Zealand. In the present study, the leaching behaviour of NZ ironsand was investigated in hydrochloric acid (2–10 M) solution at 50–80°C for 2 h. The resulting leaching liquors exhibited Fe/V ratios in the range 150–180. The distribution of trace element contaminants between solution and solid residue was investigated, and processing conditions have been determined for rapid and efficient dissolution of Fe, Ti and V into the leaching solution. In addition, mineralogical analysis of raw ironsand and leached residues was performed in order to study the leaching mechanism. Samples were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), X-ray fluorescence spectroscopy, qualitative and quantitative X-ray diffraction and inductively coupled plasma mass spectrometry (ICP). Results indicate that the dominant dissolution process follows shrinking particle mechanism. However, ironsand particles containing ex-solution lamellae exhibited a different leaching behaviour compared to homogenous titanomagnetite particles.INTRODUCTION Titanomagnetite ironsand (blacksand) forms Quaternary onshore beach and dune deposits and offshore marine deposits (Figure 1) along 480 km of coastline from Kaipara Harbour south to Wanganui on the west coast of the North Island (Christie, 2016). It attracted the attention of scientists from the earliest times (Galbreath, 1998). The principal minerals in ironsand are titanomagnetite (TTM), ilmenite, quartz and ferromagnesian minerals such as augite, hornblende, diopside, and olivine with smaller amounts of rutile and apatite (Mauk, 2016).Several large ironsand deposits have been discovered and exploited since the late 1960’s. The Waikato North Head and Taharoa mines are currently operating and they have a 2015 measured resource of 400 million tonnes in total and provide over 2 million tonnes of concentrate per year by simple cost effective magnetic separation process (Christie, 2016; Christie & Brathwaite, 1997). The concentrate contains not only 7–8% TiO2 and 56–60% SFe, but also 0.3–0.6% V2O5, is both a valuable titanium mineral and a source of vanadium. All the production is used for steelmaking industries. The other potential for utilizing more of this resource without requirement of integration into an iron and steel producing plant is to develop a hydrometallurgical route with advantages of higher efficiency along with lower emissions. Currently, there is no existing commercial process capable of extracting all three of these elements as industrial-grade commodity products. Acid leaching of TTM concentrate with higher degrees of recovery and selectivity is a key step in any possible hydrometallurgical route."

Jan 1, 2017

By L. Li

ABSTRACT Stope backfilling is a common operation in many underground mines, which requires a barricade at the base of the stope near the drift entrance to retain the backfill in place. In this paper, the distribution of pore-water pressure in barricades made of waste rock is analyzed. An analytical solution is introduced and applied to estimate the pore-water pressure along the base and full height of the barricade. Results show that the analytical solution generally accurately predicts the distribution of pore-water pressure obtained from the numerical calculations, especially in the upstream part of the barricade, where it is most critical.

Jan 1, 2013

By J. E. Hawley

"IntroductionA STUDY of the trace elements in the ash •of coals from nine seams in the Sydney coalfield, Nova Scotia, was undertaken at the suggestion of Dr. W. A. Bell, Geological Survey of Canada, as a part of a larger study of these and other Nova Scotia coals being made by the Geological Survey and the Nova Scotia Department of Mines under the direction of Dr. P. A. Hacquebard.The main purpose of this investigation has been to •determine if a knowledge of the trace element distribution might be of assistance in the recognition of individual seams, the distinction of which is not always easy or positive in folded and faulted strata by ordinary stratigraphic and structural means.The study has been so conducted as to afford information on the variation of trace elements in individual petrographic intervals or divisions in each of the seams examined, intervals determined by Dr. Hacquebard on the basis of their banded ingredients, vitrain, clarain, durain, fusain, etc, as observed under the microscope in polished sections. The results, as well, indicate the trace element composition of the coals of the area as a whole, and quantitative data for fifteen elements are given, along with concentrations of thirteen other elements, stated in terms of intensity ratios. Data on distribution of germanium, though considered here along with other elements, are dealt with elsewhere*."

Jan 1, 1955

By A Hitchen

A general outline is given for the determination of copper, nickel, cobalt, zinc, lead, cadmium, bismuth, manganese, uranium, molybdenum, vanadium, sulphate and fluoride by polarographic or amperometric methods in a variety of ores or metallurgical products. The detection of oxygen in gas mixtures by an amperometric method used as a safety device is also discussed. Introduction I N this paper, a general outline will be given of the polarographic and amperometric methods used for the chemical analysis of various ores and metallurgical products in the Chemical Analysis Section of the Extraction Metallurgy Division of the Mines Branch. The methods to be discussed will be confined to those based on the use of normal D.C. polarography and will not include those methods which utilize a cathode-ray, square wave, pulse or A.C. type of polarograph. For the sake of convenience, ? the polarographic methods will be discussed according to the type of supporting electrolyte employed, as the same electrolyte may serve to determine more than one element in more than one type of ore. Amperometric methods will be discussed according to the element to be determined rather than

Jan 1, 1965

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By K. Baris

Methane (CH4) present in coal seams, generally known as Coalbed Methane (CBM), Coal Mine Methane (CMM) or Coal Seam Gas (CSG), is a major energy source, as it is the primary constituent of natural gas. At the same time, released methane is a potent greenhouse gas (GHG) and a major safety hazard in underground mining operations. Therefore, a considerable effort has been undertaken to develop coal bed methane extraction and utilization technologies that can achieve both environmental and safety benefits. Countries with significant coal reserves and gassy seams, i.e., USA, Australia, Canada, China, India, Poland and Germany have developed mature methodologies and practices to extract, before and during mining, and utilize significant amounts of methane from coal seams. Nevertheless, on a global scale, methane recovery remains untested and many technical and economic challenges require urgent attention. The research presented in this paper, sponsored by the United States Environmental Protection Agency (EPA), is focused on the Zonguldak Basin, the only hard coal region in Turkey. The basin is known to contain very gassy coal seams and consists of three major regions: Armutcuk, Zonguldak and Amasra. Among the three, the Amasra coalfield is considered as the most favorable for CBM recovery, as it comprises of deeper coal seams and where a private company, Hema Enerji A.S. (Hema) is already developing coalbed methane production facilities. This study aims at developing a reservoir model to predict the potential CBM recovery from the CBM-2 well, the only producing CBM well drilled by HEMA Enerji A.S in the Amasra coalfield. History matching was utilized to model the 15-day production data and uncertainty analysis was performed to estimate the optimum values for the reservoir parameters. The produced model yielded an average production rate of 143 m3/day for 10 years. The total amount of CH4 to be produced during this period was 0.53 million m3. Furthermore, the total amount of GHG to be avoided was estimated at 6585 tCO2e.

Aug 1, 2013

By Cris Sideco

This paper describes the concentration processes of the Sullivan. Concentrator, including crushing , transportation, sink-float, grinding , flotation and dewatering. Handling of hot muck has had a deleterious effect on most of the processes, resulting in significant operating problems and poorer metallurgy. These problems are described -in detail. THE SULLIVAN CONCENTRATOR is situated in Kimberley, high up in the Purcell Range of the Selkirk Mountains, at an elevation of 3,600 feet, approximately 4 miles from the Sullivan Mine (see Fig. 1). The original plant went on stream on August 23, 1923 at a designed capacity of 2,500 tons per day. This has been increased in stages to its present rated capacity of 11,000 tons per day. The latest stage was in 1949, when several major projects, including the underground crushing plant, the sink-float plant and the installation of a rod mill, were completed. Some 112,800,000 tons of ore have been treated in this concentrator to November 1975. The plant started on a 48-hour/ week schedule, but was reduced to 44 hours/week in October 1946 and down to 40 hours/week by the end of 1949. Except for a 6-month period in 1952 when the mill operated continuously, the 40-hour/week, Monday to Friday schedule was in effect.

Jan 1, 1977

By B. Chareyre, H. Pourpak, L. Scholtès, E. Papachristos

"Numerical methods used to study hydraulic fracturing in low permeability rock masses need to take into account the interaction between the progressive failure mechanism of the intact rock matrix and the pre-existing natural fractures. A fully coupled hydro-mechanical 3D discrete elements model dealing with such interaction is presented here. The ultimate objective is to grasp the role of the rock-matrix failure on the propagation of the main fluid driven fracture under different stress fields and pre-existing fracture orientations. The proposed method provides the spatiotemporal distribution of the induced crack events which can be tracked during the simulations, making possible the identification of the local mechanisms leading to macro-failure in the rock matrix or reactivation of the discontinuity planes. Fluid flow inside a fracture, pressurized crack and hydro-fracking experimental tests were simulated as part of the validation process of the model and, are presented in this paper.INTRODUCTIONWith the expansion of shale gas and geothermal reservoirs exploitation, the technique of Hydraulic Fracturing (HF) has been widely used over the past years (McClure, 2012; Britt, 2012). Despite recent advances in micro-seismicity analysis or numerical modeling (Nagel et al., 2013), the way progressive failure of rocks affects the fluid flow depending on the in situ stress conditions or the rock heterogeneities is not fully controlled yet (Zoback, 2010).In this work we focused on setting up a three-dimensional discrete elements model to study fluid driven fractures propagation. The intact rock is modeled by a discrete element method (DEM) able to reproduce fracture initiation and propagation (Scholtès and Donzé, 2013, Garcia et al., 2013). The pre-existing fractures are explicitly modeled and can be individually defined or be part of a discrete fracture network (DFN) (Harthong et al., 2012). Their mechanical response is fully coupled with the fluid within a HM-DEM framework. The fluid flow and it’s interaction with the intact matrix and the pre-existing discontinuities is modeled through a Pore-scale Finite Volume (PFV) scheme specially enhanced for fractured rock modeling (Chareyre et al., 2012, Catalano et al., 2014) ."

Jan 1, 2015

By A. Grimod

The European Guideline ETAG 027 - 2008 (?Guideline for European Technical Approval of Falling Rock Protection Kits?) defines the procedures to test rock fall barriers. Nowadays, this guideline is essentially the only test and construction framework utilized by manufacturers and it is also starting to enter in the mentality of designer who can clearly specify the performances of rockfall barriers. ETAG 27 (and the related European Technical Approval and the CE marking) represents a milestone for the rockfall barrier market, because it gives the possibility to compare the performances of different fences and it ensures the quality of the certified product. For these reasons ETAG 27 presently constitutes the base for tenders all around the world. Although rockfall barriers are in common use, designers and consultants do not have a clear overview of the real performances and the technological limits of these structures. The first problem can be solved using ETAG 27 criteria, which allow designing rockfall barriers at ultimate and serviceability limit state. Even though ETAG 27 uses crash tests performed with the Service Energy Level (SEL) and Maximum Energy Level (MEL), design with these concepts is not obvious or in common acceptance. Some preliminary questions must be solved. When can these energy levels be correctly applied? In the case of rockfall simulations, what probabilistic approach must be used for the evaluation of the barrier? Unfortunately ETAG 27 does not give any information or tests relating to the technological limits of the fences. Therefore some important questions arise. How do the site specific aspects of installation affect the barrier performance? What is the behaviour of the barriers under extreme conditions? And finally, the main question lies in the background: what is the functional reliability of ETAG 27? All of the above questions require comprehensive answers, which is consistent with the experience of designers, installers and producers. Officine Maccaferri S.p.A., with its 130 year experience in the field of rockfall protection, collected a large number of case histories with barriers impacted by single or multiple blocks, debris flows, and snow avalanches. Throughout these case histories and in accordance with a recent Italian standard code, it has been possible to implement a reasonable design approach that considers the efficiency of the barrier, the uncertainties of the input data, and the fore

Aug 1, 2013

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By A. R. Laplante

"In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and as such they perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is ineffective in recovering very fine ( <15 µm) or flaky gold, as encountered in flotation feeds, concentrates or tails. It is the: preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 µm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm3 ), especially from coarser gangue. INTRODUCTIONThe purpose of this presentation is to describe the mode of operation of two Canadian centrifugal concentrators, the Knelson and Falcon. It is hoped that it will prove informative to prospective users in the selection, testing and optimization for applications of either machine. The work is based on testwork both in Canadian mills and at McGill. I am indebted to many colleagues at these locations. Appropriate references will be made to articles further describing the work, either already in the open literature or in preparation.Although this work is meant to be more practical than scholarly, it is appropriate to begin by considering how the two units achieve selective recovery. This will become useful in establishing a suitable testing methodology, which will then be described, and interpreting typical results. In the last section I will attempt to define appropriate applications for the two units. This is a thankless task, as I am likely to miss some applications or to make projections based on partial results, as much of the work is still in progress. In deference to the reader and both manufacturers, areas where reasonable doubt still remains will be identified."

Jan 1, 1993

By E. Mohammadi Zahrani

In this study, Mg-doped fluorapatite (Mg-FA) nanopowders were prepared through a sol-gel, technique and characterized. Designated degree of Mg2+ ions incorporation into the apatite structure was indicated by the x value in the general formula of (Ca10-xMgx (PO4)6F2), where x=0, 0.25, 0.5, 0.75, and 1. XRD, AAS, FTIR and TEM techniques were utilized to characterize the synthesized nanopowders. In vitro bioactivity of the powders was evaluated in simulated body fluid. Powders had a crystallite size less than 100 nm. It was concluded that Mg-substitution could alter bioactivity and dissolution behaviour of Mg-FA. These two parameters were proportional to magnesium content of the powders.

Jan 1, 2010

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

By A. A. Millar

THE output of coal from the Province of Alberta reached its peak; in the year 1928, when 7,334,179 tons were produced. Following this, a steady decline was recorded, and in 1930 a low mark of 4,564, 290 tons was made. Since that time, however, the tendency has been upward, and this year (1937) 5,551,682 tons were produced, compared with 5,696, 375 tons in 1936 and 5,462,973 tons in 1935. The value of the output in 1937 was $14,434,969, against $14, 720,004 in 1936. The coals of Alberta have been classed under three heads, viz., domestic, sub-bituminous, and bituminous The domestic (or lignite) and the sub-bituminous coals are used chiefly for domestic purposes, with the possible exception of the smaller sizes and the output of the two stripping pits at Stereo and Coal Valley The bituminous output is used mainly by the railways, for locomotive purposes, which, in 1937, accounted for 80.6 per? cenr of the total sales of bituminous coal. A fair proportion is sold for stationary engine and steam purposes and, in 1937, 25,000 tons were used in making briquettes at plants operated by the Canmore Coal Company, Limited, and Brazeau Collieries, Limited. The International Coal & Coke Company, Limited, used 99,500 tons in their plant at Coleman, for making coke. The bulk of the 66,000 tons of coke produced was sold for use at the smelter at Trail, B.C.

Jan 1, 1938