Search Documents

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By E. M. Watkin

"Land directly disturbed by hard rock mining activities in Ontario and Quebec was surveyed in 1974 as part of a country-wide assessment, (Murray 1977). Some 15, 000 hectares, or 5 7 square miles, are listed as having been disturbed by overburden removal, waste rock and tailings deposition (Table 1) in the region. That area represents sixty-eight per cent of the total area which ha1; been disturbed by mining in central and Atlantic Canada. Assessment of disturbed areas was undertaken using LANDSAT-1 and LANDSAT-2 satellite imagery. Certain limitations of the technique were recognized but the data obtained were considered a relatively acceptable assessment of the extent of disturbed areas larger than ten hectares.Approximately ten per cent of the land disturbed by mining in the two provinces has been reclaimed to varying degrees. Indeed, this proportion is correct for the country as a whole. As pointed out by Ripley, Redmann and Maxwell (1978), some of the land was disturbed long before environmental concern 01· reclamation were ever considered. In numerous instances reclamation will remain impossible until presently active operations are closed. Nevertheless, these authors feel such figures make it clear that reclamation has not been a high priority in Canada in the past. Canada is a vast country, and there has been little pressure toward efficient use of all land space. Most mining operations occur in areas distant from the country's population centres. Under these circumstances, therefore, the pressure to reduce the environmental impact of mining is much less than in the more densely populated areas of Europe and the eastern United States, where such activity can occur in or adjacent to large metropolitan areas."

Jan 1, 1980

By Dennis V. Woods, J. Duncan Crone

"In order to determine its capabilities and to aid in the interpretation of fie ld results, a scale model study and field tests were carried out on the Crone borehole pulse electromagnetic (PEM) system. The model results indicate that if a borehole passes in the vicinity of a tabular conductive body, the system will not only detect the presence of the body, but will also return information as to its conductivity-thickness product, size, altitude and position.The effect of variation of these electromagnetic and geometric factors on the shape of the response curve from a borehole PEM survey is displayed by a number of suites of scale-model response curves. These model curves can be used directly as type curves in the interpretation of field results. Field tests of a prototype PEM system provide a check on the scale-model results and also summarize the procedure of interpreting field data using the model type curves.The borehole pulse EM system can be effectively used as a follow-up geophysical instrument for locating and delineating known conductive bodies. It can also be profitably utilized as a primary geophysical exploration tool in areas of deep mineralization below the depth limit of conventional airborne and ground geophysical systems. The probed area of a diamond drill hole in these cases is increased from a 1- inch drill core to a zone extending hundreds of feet from the hole."

Jan 1, 1980

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By H. Stocker, C. E. Makepeace

"This paper presents the statistical analyses of several sets of data acquired in several programs of sampling of radon daughters in uranium mines. The measurements were taken over periods of days or weeks for given locations or location occupations within these mines. Because the sampling applies to specific intervals of time and specific locations, a method is suggested f or the eventual application of a monitoring program which would be suitable on an annual basis for these locations. The present data and analyses thereof are not justifiably applicable to a monitoring regimen on an annualbasis, without a number of additional assumptions.The aim of the present analyses of concentration measurements is the determination of the minimum number of measurements required to achieve an annual radon daughter exposure estimate, for individual workers, having an error no greater than 50% at the 95% confidence level. The criterion of accuracy is taken from a statement in the American National Standard, Radiation Protection in Uranium Mines (ANSI NI3.8-I973), and is currently used, in somewhat modified form, as a guide to uranium mining licensees in Canada. Uncertainties associated with occupancy time are ignored in the present analysis. IntroductionOne of the principal aims of any scheme of radiation protection is that of improving the accuracy of exposure estimation for workers. The example presented here is from the area of radon daughter exposure estimation for uranium miners. The conventional means of estimating workers' exposures is grab sampling of radon daughter concentrations combined with occupancy time weighting in the various work and travel locations. Uncertainties exist in each of these components, and in an environment of highly variable radon daughter concentrations (such as an active uranium mine) one is always uncertain as to the representativeness of the grab sample (compared to the average concentration) unless a sophisticated monitoring scheme has been implemented based on previous experience in such an environment.Improvements in the accuracy and precision of employee radon daughter exposure records depend, primarily, on three factors;"

Jan 1, 1980

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By André Gobell

"La distribution des éléments majeurs dans une séquence de roches volcaniques felsiques, la formation de Waconichi, au sud de Chibougamau, indique que les roches pyroclastiques du secteur ouest de ce segment sont chimiquement anormales si on les compare à la composition moyenne des roches volcaniques de Chibougamau: elles sont caractérisées par une teneur anormalement élevée en f er, en magnésium et en potassium et une teneur anormalement basse en sodium et en calcium; ce chimisme caractérise les encaissants des dépôts de sulfures massifs d 'origine volcanique.Les coulées rhyolitiques massives sous-jacentes au gite de cuivre-zinc avec or et argent de Lemoine ne montrent pas ou très peu d’altération de ce genre. Le schéma de mise en place des dépôts de sulfures massifs d'origine volcanique et la nature des roches en présence permettent de croire que la zone d'altération mise en évidence à l'ouest de la mine Lemoine puisse être reliée à la mise en place de ce gisement d'ou l'im portance de tenir compte des caractères texturaux des roches lors de l'interprétation de données litho géochimiques."

Jan 1, 1980

By D. A. Barr

"Most of the lode and placer gold production in the Canadian Cordillera has been derived from mines and placers in the Intermontane and Omineca belts. Gold has been produced from rocks of Precambrian to Eocene age, but the preferred host environment contains Upper Paleozoic to Upper Jurassic eugeosynclinal or arc-type sedimentary and volcanic rocks adjacent to plutonic complexes which have a wide variety in both size and composition. Auriferous quartz lodes occur in fissures and shear zones which are commonly subsidiary to strong fault zones. In common with most vein-type deposits, structural complexities are an essential part of the mine environment.Gold production from the Canadian Cordillera to the end of 1978 totals 35.0 million ounces, of which 47 per cent has been produced from placer mining, principally in the Klondike and Cariboo districts. The balance has been derived from lode gold (80 per cent) and base metal (20 per cent) mines.Gold reserves in producing mines and deposits committed for production as of January 1, 1978 were 87.4 tons, or 21.6 per cent of total Canadian gold reserves contained in all types of deposits. Although more than 100 lode mines have operated in the Canadian Cordillera since the turn of the last century, over 75 per cent of the lode gold produced by 1978 was recovered from five mining camps, namely the Rossland, Hedley, Bridge River, Premier and Barkerville.The average grade of the principal producers in these camps was about 0.45 ounce of gold per ton. Individual camps yielded from 3 to 8 million tons during their operating lives, which varied from 28 to 43 years. The last of these mines ceased operating in 1971.Most of the total lode gold production has been derived from quartz veins, frequently with associated carbonate and ankerite, occupying fractured and faulted zones in Mesozoic volcanic and sedimentary rocks closely associated with a variety of intrusions. A review of the literature suggests that several deposits may have evolved by remobilization of ore constituents from earlier concordant gold-bearing formations. The principal metallic minerals in the deposits are native gold, electrum, tellurides, pyrite, arsenopyrite, pyrrhotite, sphalerite, galena and chalcopyrite.As the mineralogy suggests, many of the Cordilleran lode gold deposits have yielded important co-products or byproducts, including silver, copper, lead, zinc, cadmium and tungsten. Significant by-product gold production has also been derived from porphyry copper, volcanogenic, replacement and pyrometasomatic deposits, particularly in recent years.No major lode gold discovery has been made in the past 67 years, although little exploration activity for gold has taken place during the last 30 years. Several relatively small lode gold and gold replacement deposits have been discovered in recent years, either serendipitously (Chappelle) or on very low initial budgets (Northair and Carolin). Based on well-established precedents, one or more of these may eventually be developed into a large mine.A detailed study of the Canadian Cordillera gold deposits based on recent genetic models could prove rewarding, not only in up-dating information on their origin and depositional characteristics, but in stimulating the search for undiscovered gold deposits, in the Cordillera and other parts of Canada."

Jan 1, 1980

By J. C. Botham, T. D. Brown

"Coke is the most costly item in steelmaking via blast furnaces . Recent innovations in cokemaking have been directed toward reducing this cost while simultaneously improving coke quality and expanding the range of coals used in the process. It is also important to meet increasingly stringent environmental legislation.Improvements in coke quality have been achieved by novel blend selection procedures, by charge density control using both selective pulverization and partial briquetting, and by the use of modifying additives.The Canadian Carbonization Research Association provides a focus for Canadian cokemakin g research which has demonstrated these technologies in a series of pilot-scale experiments."

Jan 1, 1980

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic metres /day of wastewater containing 30-60 mg/1 zinc. demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic con¬trol equipment, the system has evolved to a full-scale operation capable of treating 800 cubic metres/day of wastewater containing 4-11 gm/1 zinc. Treated effluent contains 0.2-20 mg/1 zinc. The hydroxide sludge produced returns to the metallurgical process for the recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing a return from metal recovery.IntroductionWith the goal of reducing environmental contamination, Hudson Bay Mining and Smelting began laboratory testwork, during the late 1960's, into the methods and technology for neutralizing and removing heavy metals from acid mine drainage. Based on lime treatment, early tests showed much promise and culminated in the construction of a pilot-scale test plant at Schist Lake Mine in early 1971.This pilot system utilized technology developed in laboratory studies, and related to work then underway by state authorities in Pennsylvania coal mines. The basic operation consisted of a lime slurry tank, baffle reactor and a free-settling basin. Through three summers of operation, the Schist plant, capable of treating 600 cubic metres/day of minewater, produced a heavy-metal extraction of 99% under normal conditions. Although successful in proving the treatment chemistry, the plant displayed deficiencies in sludge densification and handling."

Jan 1, 1980

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By G. E. Norman, J. F. Jackson, A. L. Mckague

"The treatment of nickel-copper concentrate in the new smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, is described. The concentrate in a slurry form is partially roasted in a fluid-bed roaster and the calcine is smelted in an electric furnace. The roaster gases are treated in an acid plant. IntroductionSmelting began at Falconbridge in 1930 with the first blast furnace treating high-grade ore containing 2-3% nickel. In 1933, the Falconbridge concentrator was built and started producing a bulk sulphide concentrate containing 4% nickel. A sinter plant was built to agglomerate and partially roast this concentrate. The sinter was smelted in blast furnaces along with high. grade magnetic ore. Matte from the furnaces was treated in Pierce-Smith converters to produce shipping matte which was refined at the company's plant in Norway."

Jan 1, 1980

By R. G. Achter, E. Wilson

"This paper describes the work undertaken to renovate the Pipe Open Pit drainage system, incorporating measures to improve effluent quality. It describes the technical feat of drilling an l l-inch-diameter hole from the bottom of the open pit for a distance of 1100feet to intersect an underground drift. An innovative method of checking the inclination of this hole is also described. The paper outlines the construction required on the 1500-foot level of the underground mine to facilitate water impoundment and slime settling, as well as the instrumentation for control of water flows. IntroductionThe Manitoba Division of Inco Metals Company operates two mines-an underground mine at Thompson and an open pit at Pipe. The Pipe Open Pit is located 20 miles southwest of the City of Thompson, approximately 400 miles due north of Win nipeg(Fig. 1).Surface diamond drilling of the Pipe ore body was sta rted in 1959. In 1961, a shaft was sunk to a depth o f 1,570 feet to carry out further exploration work and obtain bulk ore samples for metallurgical testing. Site preparation to mine the upper portion of the orebody as an open pit was initiated in 1966 and by late 1967, the removal of silt and clay overburden was in progress. The contractor completed the dredging in the fall of 1969. Over 12 million cubic yards of muskeg, clay and silt was removed, which in some places was 150 feet deep over the orebody. Production began in early 1971, by which time the top three benches of rock had been excavated and the orebody exposed.The Pipe No. 2 Mine main shaft was started in 1970 and completed in 1973 at a depth of 3,160 feet. Development for exploration purposes was carried out on the 1500 and 2460 levels, and permanent pumping facilities were installed.The surface dimensions of the open pit are 2,200 by 1,600 feet, with the long axis striking northeast. The walls are designed with a 45- to 50-degree slope and the ultimate design depth is 720 feet. The present depth of the pit is 520 feet and production capacity is 6,800 tons of ore per mine day."

Jan 1, 1980

By John Tribe

"This paper gives the organizational history of Luscar Ltd. and its various coal producing operations. Each 0/ the operations is then described individually. They include the Bienfait Mine, the Boundary Dam Mine, the Diplomat Mine, the Luscar Mine and the Coal Valley Mine. The company's plans/or expansion are also discussed. IntroductionLuscar Ltd. is an Edmonton-based energy company formed in 1967 through an amalgamation of two pioneer coal companies-Mountain Park Collieries and Luscar Coals Ltd. In 1912, Mountain Park Collieries initiated the development of an underground mine in the Coal Branch area of Alberta. This mine necessitated the establishment of a townsite and the provision of rail access. The second operation, Luscar Coals Ltd., was established in 1921 at Luscar, Alberta. This was also an underground operation and required the development of a rail spur and townsite. The product from both mines was used to fuel railway steam locomotives until the 1950's. The market demand for coal decreased as the use of the diesel locomotive increased, so that these operations were finally closed in 1954. Through the amalgamation of the two companies in 1967, however, Luscar Ltd. was formed to become an active participant in the revival of coal operations. Western Canadian Luscar Ltd. is involved in the exploration, development, production and marketing of coal, coal products, oil and gas. Luscar Ltd. is currently participating in five producing mines (Fig. I). The Diplomat Mine, approximately 125 miles southeast of Edmonton, was in production when it was acquired in 1949 by Luscar Coals Ltd. In 1966, the Bienfait Mine and char plant were added. The Luscar Mine, which is a 50/50 joint venture of Luscar Ltd. and the Consolidation Coal Company of Canada, and is operated by Cardinal River Coals Limited, started production in 1969 on the original Luscar Coals Ltd. mine site. The Boundary Dam Mine was opened in 1974. Both the Bienfait and Boundary Dam operations are located in the lignite coal fields of southeastern Saskatchewan. The most recent addition to the group is the Coal Valley Mine, 40 miles southwest of Edson, Alberta. It commenced commercial production in July, 1978 under the operation of Luscar Stereo (1977) Limited."

Jan 1, 1980

By Michael Jerome Wallace

"This paper refers to the wet open circuit ball mil ls in operation at Sidbec-Normines'5 pelletizing plant at Port-Cartier, Quebec, which commenced operations in late November· 1977. Prior to detailing our experiences in the grinding area at Port-Cartier, a general description of the total Sidbec-Normines project is outlined.HI STORYSidbec-Normines was incorporated in 1976 to develop the Fire-Lake - Port-Cartier iron ore mining, concentrating and pelletizing project. The primary objective of Sidbec-Normines is to produce 6mi11 ion tons per year of oxide pellets, of which 3 mi 11 ion tons per year are of a low silica grade suitable for direct reduction purposes. The participants in the project are Sidbec, the Quebec Government steel producer, British Steel Corporation (lnt'l) and the Quebec Cartier Mining Company. Equity interest is held in the company by the participants in the proportions of 50.1%, 41.6:7% and 8.23%, respectively."

Jan 1, 1979

By E. C. Sanford

A laboratory-scale batch extraction unit and operating procedure for studying the hot-water separation of bitumen from Athabasca tar sands are described. The extractor evolved from earlier units and has been in use by Syncrude Research for the past 10 years. By using a unit such as this, it is possible to study tar sand feed quality and the effects of chemicals on the hot-water extraction process, while process variables are held constant. Data are presented to demonstrate the importance of surfactants to the process and the interrelated role of inorganic bases and surfactants.

Jan 1, 1979

By Young C. Kim

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. However, no formal framework for a proper analysis has existed to date. This paper summarizes the material contained in the Design Chapter Supplement (5-3) of the Pit Slope Manual. The supplement describes the results of the research effort in which a formal economic analysis framework was developed and tested through a case study. The case study results have demonstrated the practicality of the developed procedure and the availability of required data under "real-life" conditions.

Jan 1, 1979