Search Documents

By M Fishwick Tapia

This paper was prepared and translated from the final report of the investigation into the Codelco Chile Salvador DivisionÆs air blast which occurred in the Inca-West area. In this section of the block cave mine, a stable arch formed covering an area of approximately 15 000 m2 . This zone subsequently collapsed producing a massive air blast. The collapse followed a series of planned extraction activities and occurred on 5 December 1999. This paper discusses the cave back arching event and the measures that were taken in order to induce the controlled collapse. This was to minimise risk to personnel, equipment and installations. The results obtained to date are presented.

Jan 1, 2000

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

The Department of Mineral Resources is the lead agency in mine site environment management and control in New South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.

Jan 1, 1995

By J Nixon

I have to say that my story is not too much different to many others who grew up and worked in the great mining fields like Broken Hill, Mt Isa, Rosebery, Kalgoorlie or Kambalda and any one of them could have stood up here and spun you a good yarn.What does my paper offer you in this volume? By sharing my experiences I want to encourage you to consider your own experience with leadership, taking on change, learning from and contributing to the development of others.I have been very fortunate to be part of many new innovations into underground mining over the past 40 or so years; most of it with Conzinc Rio Tinto Australia (CRA)/Rio Tinto operations.•From hand-held drills and a homemade single boom Jumbo mounted on an old Airtrak, to the sophisticated twin boom jumbos with high speed drifters all controlled by an on-board computer;•from a Scraper winch and a Wagner 2D loader to fully automated electric LHDs that navigate to the tipple, empty the bucket and return to where they come from;•from hand-held cut-and-fill and timber stoping in Broken Hill to the bulk mining methods of a block cave where at Northparkes we mined more ore in a month than we mined in the total five years of operations at Currawang;•from hand-held scaling and bolting with no skin protection to installing ground support with Jumbos and sophisticated Cable Bolters and the introduction of in cycle shotcrete;•from hand-held ladder rising and shaft sinking to Box Hole rigs, Raise Bore Machines and Blind Hole shaft sinking; and•from Gelignite based AN60 stick explosives, ANFO, fuse firing and half second detonators to Powergel, Emulsions and electronic computer programmed detonators that can somehow be initiated by ‘Blast Ped’ travelling through the rock.

Mar 21, 2011

By D Bradshaw, R Dunne, S Farrokhpay

It is well known that clays affect the flotation performance, and many of the refractory gold ores around the world contain clay minerals. Therefore, an ore sample from the Carlin Trend was selected for this study as these ores contain large quantities of clays. The presence of clay minerals in an ore makes it susceptible to a range of variables, such as the solution chemistry determined by pH and the chemistry of the rheology modifiers. The viscosity of the ore slurry was measured as a function of solid concentration and particle size distribution, in addition to using different rheology modifiers and pH regulators. The results were correlated with the ore flotation performance. It was found that various reagents known commonly as dispersants or rheology modifiers have different effects on the ore slurry viscosity. This study revealed that the gold flotation recovery can be improved by changing the pulp rheology.CITATION:Farrokhpay, S, Bradshaw, D and Dunne, R, 2013. Rheological investigation of the flotation performance of a high clay containing gold ore from Carlin Trend, in Proceedings World Gold 2013, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By B Clements, G Lane

The operations and project environments are very different, but overlap in many areas. The development of mineral processing projects is goal oriented, is schedule focused and is a contractual environment. The operating environment for a mineral processing plant is oriented around longer-term commitments, focused on delivery against budget expectations, and an environment heavily influenced by long-term personal relationships, community relationships, and people issues.Further contrast is evident in the way expenditure is managed. Projects commit large amounts of money quickly to meet schedule-based objectives. Operations manage expenditure to minimise operating costs and are able to, or are forced to delay decisions on large expenditures. However, these two environments need to come together in many ways, ranging from greenfields plant handover to a new operations and maintenance crew, to day to day interaction and management of brownfields projects, often in close proximity.This paper considers the different perspectives people bring to projects and early operations, including the advantages and disadvantages of æoperationsÆ input to a project and models for managing value adding during project development, implementation and debottlenecking.CITATION:Lane, G and Clements, B, 2012. Operations versus projects - How do people think and what are the implications?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference , pp 11-16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By B Davis, A H. Benzer, A N. Mainza, C M. Evertsson, L M. Tavares, M M. Hilden, M S. Powell, C Rule, G Asbj÷rnsson

The Mogalakwena North Concentrator of Anglo Platinum Operations was built with the capability to allow for future projected expansion. Several research groups, currently working with Anglo American on collaborative research over a range of projects, were brought in to review the existing operation, with a view to releasing some specific bottlenecks and providing specialist design input to the potential plant expansion.Based on a thorough review of the high pressure grinding rolls (HPGR) and crushing circuit, a wide range of de-bottlenecking opportunities were identified. This was followed by a series of surveys to provide performance measurements and to model the circuit in detail. From this effort a full simulation of the plant has been developed, including updated models of the HPGR, crusher, bins and screens. These models have been implemented in the researchersÆ Model Development Kit (MDK) version of JKSimMet, and in a prototype dynamic simulator based on the Matlab Simulink software.The observations, measurements and simulations have provided guidance and quantified the benefits of some proposed circuit modifications. Based on these findings a number of upgrades are being planned, with the aim of ensuring full utilisation of the installed equipment. The circuit demonstrates a potential expansion of over 30 per cent through minor improvements, and a 70 per cent increase in capacity with the addition of some strategic equipment.The HPGR-crushing upgrade project demonstrates the potential benefits of nurturing disparate Research groups into a strong inter-disciplinary technical team capable of supporting operational needs while developing future technology.CITATION:Powell, M S, Hilden, M M, Evertsson, C M, Asbj÷rnsson, G, Benzer, A H, Mainza, A N, Tavares, L M Davis, B, Plint, N and Rule, C, 2012. Optimisation opportunities for high pressure grinding rolls circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 81-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M J. Ireland, D P. Horne, S J. Simpson

The Sinclair Nickel Project, wholly owned by Xstrata Nickel Australasia (XNA), includes an underground mine, a concentrator, a village, an all-weather airstrip and associated mine infrastructure. The operation is located 70 km north of Leonora in the prospective and historically productive eastern Goldfields region of Western Australia. Xstrata Nickel has successfully developed the Sinclair deposit into a 350 kt/a operation since its discovery in November 2005, with contained nickel metal production to date in excess of 10 600 t, of which 5500 t is from the underground operation.The narrow, continuous, medium-grade Sinclair nickel sulfide deposit accessed by the Phoenix Decline has a shallow 15¦ - 20¦ plunge that is approximately 1000 m long down dip and open at depth to the north. The flat plunge and low-grade nature of the orebody presents challenges regarding the amount of horizontal waste development that can be economically excavated, which in turn affects ventilation, egress, mine services and diamond drilling.The mineralisation is hosted between an ultra mafic hanging wall and a basalt footwall and is being mined using a bottom up, sublevel open stoping method. The stopes are retreated to a central access, filling voids in the process with waste mullock where possible and using cemented mullock fill where end exposure is required. Tight filling the flat dipping hanging wall has proved to be challenging given the angle of repose for the waste mullock fill is steeper than the angle of the hanging wall.Reconciliations of mine performance against the original feasibility study show positive changes and operational optimisations enabling Sinclair to achieve its mining targets in a safe, sustainable and economic manner. This paper discusses the mining operations associated with the first two years of the Sinclair Underground Nickel Project, providing an overview of the various issues encountered and the lessons learnt in the process.CITATION:Ireland, M J, Horne, D P and Simpson, S J, 2012. Overcoming mine design and production challenges at the Sinclair underground nickel project, in Proceedings Narrow Vein Mining 2012 , pp 37-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By D M. Verster, P L. Gillot, A Kone

Randgold ResourcesÆ MorilaÆs gold leach plant is subjected to uncommon æoxygen stressesÆ. Feed ores exhibit very high oxygen demands, primarily caused by iron sulfides. In addition, ore oxygen demand varies significantly over time, as well as between different feed ore sources. The inability of the Morila gold leach plantÆs oxygenation system to cope with these high and fluctuating oxygen stresses manifested itself in variable gold residue grades, and cyanide consumption rates.Management launched a Morila oxygen system review project during September 2009, with the objective of auditing the performance of the then current oxygenation system, against required performance parameters as calculated from oxygen demands of the various feed ore types and targeted dissolved oxygen levels in the leach train.This paper describes the systematic changes made since 2009 to the Morila oxygen system in four main areas: O2-supply plant, O2-volumes, O2-controls and oxygenation equipment. Data are provided on corresponding improvements in leach plant performance. Theoretical, as well as practical aspects of gold leach oxygenation systems are covered.CITATION:Verster, D M, Gillot, P L and Kone, A, 2013. Oxygenation system upgrades and leach plant performance improvements at Morila Gold Mine - 2009 to 2012, in Proceedings World Gold 2013 , pp 215-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By B Ekberg, R Salmimies, T Kinnarinen, A HSkkinen

The regeneration of the ceramic filter medium used in iron ore dewatering is often done by combining backwashing, ultrasonic cleaning and chemical regeneration. Of these three, the first two are applied more frequently, whereas chemical regeneration is done only when needed, eg once a day. Chemical regeneration of the ceramic filter medium in iron ore processing can involve the use of oxalic acid to dissolve the iron oxide particles. Even while performing simple chemical regeneration, meaning no ultrasound to assist the cleaning, the changes in the performance and in the structure of the filter medium could not be explained solely based on the dissolution or the removal of particles from the surface. Good regeneration results were obtained at 35 and 50¦C, meaning that the final permeability of the filter medium corresponded to that of unused filter medium. Permeability of the medium after regeneration at 15¦C was also good after 12 h, but did fall short of those regenerated at higher temperatures. Changing the acid concentration did not seem to have a significant effect on the regeneration.CITATION:Salmimies, R, Kinnarinen, T, Ekberg, B and HSkkinen, A, 2013. Particle dissolution in the chemical regeneration of the ceramic filter medium used for magnetite dewatering, in Proceedings Iron Ore 2013 , pp 473-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C M. Zammit, N Cook, F Reith, C L. Ciobanu, J Brugger

The role of biological agents in the gold mining industry is currently limited to the use of microorganisms in bioleaching and bioremediation. However, there is a variety of possibilities in which biotechnology could aid the mining industry in the future. In this article we discuss the potential for the development of these novel biotechnologies and the role they can play in the exploration for new gold deposits, the processing of ores and the post-mining remediation of sites. The development of these biotechnologies has been enabled by rapid advances in our molecular-level understanding of the role microorganisms play in the solubilisation, dispersion and precipitation of gold. An understanding of the distribution of microbial species in soils overlying mineralisation can be utilised to develop bioindicator systems that assist with gold exploration. An in-depth knowledge of how microorganisms interact with gold complexes is being used to develop in-field biosensors, supporting exploration. Processing technologies may be improved based on advances in our understanding of the interactions between microorganisms, ore minerals, cyanide and gold. For instance, cyanide-producing microorganisms are being investigated for use in in situ leaching of gold. In turn, the use of cyanide-utilising microorganisms for the degradation of cyanide is being explored. Combined, the implementation of these biotechnologies in the gold mining sector may revolutionise the industry, leading to greener, more efficient exploration for and extraction of gold.CITATION:Zammit, C M, Cook, N, Ciobanu, C L, Brugger, J and Reith, F, 2013. Possible future applications of biotechnologies in the gold industry - a prospective approach, in Proceedings World Gold 2013 , pp 233-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J E. Everett, D Linden, P Maney

In response to the implementation of a new schedule for iron ore fines in the International Maritime OrganizationÆs (IMO) International Maritime Solid Bulk Cargoes (IMSBC) Code, improved measures for the management of moisture have been developed. In particular, prediction of cargo moisture allows management of iron ore fines within the supply?chain to facilitate the safe?shipping of iron ore fines.An ARIMA model, augmented to allow for shipment tonnage, has been developed to predict the moisture level from previous shipments of the same product. The model explains about 60 per cent of the moisture variance. It was found that inclusion of other available information, such as ore composition, train/rake assays and recent rainfall at port and mine, did not add to the predictive power of the model.CITATION:Everett, J E, Linden, D and Maney, P, 2013. Predicting iron ore fines shipment moisture, in Proceedings Iron Ore 2013 , pp 17-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Yates, C C(te, M Rodgerson

This paper describes how specific technical and regulatory issues related to water management have been dealt with at Anglo AmericanÆs Moranbah North mine. It compiles the collection of practices that have been implemented since 2010 in response to climatic and regulatory drivers. Operations must continually evolve as they face emerging challenges. For Moranbah North mine, one key challenge is the integration of its mine water system to that of its new neighbouring mine Grosvenor. The commitment to ongoing improvement has placed the mine in a good position to face this particular challenge.Water-related risks were identified then mitigated by technical practices, which have focused on improving underground water management, increasing storage capacity and installing a state-of-the-art control system for the management of water on-site and for releases of mine-affected water to the environment. These practices are supported by an extensive monitoring and audit system that provides confidence in the reporting of activities and outcomes. The strategy has helped the operation with its continual attempts to minimise reliance on high-quality third-party water and improving its interaction with the surrounding environment and community.CITATION:Rodgerson, M, Yates, D and C(te, C, 2013. Leading practice water management at Moranbah North Underground Mine, in Proceedings Water in Mining 2013 , pp 301-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By M I. Pownceby, A Torpy, C Johnson, N C. Wilson

To extract uranium from low-grade, calcrete-hosted uranium (CHU) ore is challenging owing to the presence of carbonate and swelling clay gangue minerals that require an alkaline lixiviant to be used. Western Australia possesses ~75 000 U3O8 t in CHU resources. Improvements to alkaline leach extraction practices would improve the economic potential of these deposits.A column leach study of CHU ore was run for 105 days using an alkaline carbonate-bicarbonate lixiviant. The uranium content of the liquor plateaued after 75 days at ~275 mg U/L; the calculated maximum solution capacity was 800 mg U/L. Spiked peaks and troughs were seen in the data set beyond the 60th day, where concentrations ranged from 220 - 290 mg U/L, indicating possible cyclic uptake and loss of uranium from the solution.Pristine and leached ore samples were geochemically analysed and mineralogically characterised at high resolution using a field emission gun-electron probe micro-analyser (FEG-EPMA). Results showed that leached ore samples from the top of the column contained less carnotite than pristine ore. In contrast, leached ore samples from the column base contained regions with more carnotite than pristine ore, indicating precipitation. Three carnotite grain micro-structures were identified in the leached ore; fan-spherulite, granular and core-shell cubes, with evidence for multiple growth phases.Evidence of carnotite precipitation was seen at the edge of and in pore spaces within montmorillonite and dolomite grains. The point of zero charge of both minerals is lower than the pH of the lixiviant (pH 10.8), thus the mineral surfaces are negatively charged and would not attract UO2(CO3)34- ions out of solution. Similarly, the decrease in the uranium content of the lixiviant is not attributed to super-saturation, as this was unlikely to have been achieved. Work is ongoing to understand the reason for carnotite precipitation and the fluctuations in the lixiviant uranium concentration that are seen.CITATION:Johnson, C, Pownceby, M I, Wilson, N C and Torpy, A, 2013. Microscale characterisation of pristine and processed ore - implications for leaching calcrete-hosted uranium ore, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 303-316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J T. Carswell, N A. Schofield

Fluctuations in periodic reconciliations between the mine and the mill are an expected and common experience in mining and processing operations. These fluctuations are caused in part by errors in the estimates of tonnage and grade of the mined material as well as errors in the millÆs assessment of the material processed. Keeping these errors small and unbiased is an important aspect of an efficient operation whose primary goal is to derive maximum benefit from the exploitation of the mineral resource.These fluctuations in periodic reconciliations can also mask subtle but economically important problems which may take years to identify and resolve. Such problems can result from a poorly-conceived model of the mineralisation which affects both the spatial distribution of the ore as well as the tonnage - grade distribution over the range of cut-off grades. Poorly conceived models of the mineral resources and ore distribution can arise as a result of insufficient and inadequate?drilling and sampling of the mineralisation, inappropriate?application of geological?constraints in the estimation process and the use of inappropriate methods to estimate the block grade distribution. This paper presents three case studies from gold and copper mining operations, two of which experienced significant problems with their mine to mill reconciliations over extended periods of time. For the gold mine in case study 1, sampling problems were ultimately considered to be the main cause of the poor reconciliations between grade control predictions and the mill which persisted over a period of 18 months. In addition, incorrect application of resource modelling methods contributed significantly to a mismatching of the mill capacity with the mine at the beginning of operations. For the underground copper mine in case study 2, a change in the approach taken to resource modelling brought marked improvements in ore definition and more accurate predictions of ore grade and better production forecasts.The third case study describes the background to the expansion of production to exploit a large tonnage of lower-grade stockwork mineralisation in an open pit gold mine. Several years of favourable Mine to Mill reconciliation data from the mining and processing of higher grade and lower grade stockwork styles of gold mineralisation provided the confidence in the approach to grade control to support the expansion plans during a period of low gold prices.The paper is intended to complement the discussion of mineral resource estimation methods and risks in Section 6.1.3 of the Mine ManagersÆ Handbook to be published by the Australasian Institute of Mining and Metallurgy (Schofield, 2012).CITATION:Schofield, N A, Moore, J and Carswell, J T, 2012. Mine to mill reconciliation - Three case studies, in Proceedings International Mine Management 2012, pp 161-172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

By Takagi T, Seetharam R, Sie SH, Naito K

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medical/high-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnSZ), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995