Search Documents

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

Establishing the link between the solid, cold rock of dikes, sills, plutons, and lavas and hot, active magma chambers is the quest of igneous petrology. Differentiation of Earth, the diversity of the igneous rocks, and the spectacle of volcanism are ample evidence that magmatic processes are fundamental to our understanding of planet formation and evolution. Single gabbroic plutons, on the other hand, often show intricate and abundant evidence of the effects of crystal growth and sorting. It has not proven simple, however, to establish the basic principles of magmatic behavior leading to this crucial evidence. Because of their abundance, exposure, simple geometry, large range in size, and often straight-forward petrology, sills are excellent examples of the magma chambers. Physical and chemical processes operating in sills can be recognized that also routinely operate in many other bodies. Understanding the dynamics of sill solidification is essential to understanding the genetic links between lavas and plutons.

Jan 1, 1990

By O Ignatenko, A van Schaik

Environmental legislation for the process and manufacturing industries is frequently formulated without considering the fundamental limits of physics, chemistry and thermodynamics within process technology. Recycling of end-of-life goods is used in this paper to show how the limits can be evaluated on the basis of the theory of minerals processing and metallurgical engineering. This theory has been applied on European Union level to re-examine the legislation for automobile recycling in a recent stakeholder discussion involving the automotive industry (http://www.assurre.org). This theory and our models are finding their way into the computer aided design (CAD) tools of the automotive industry, developments that form part of a project to design the super light car of the future (http://www.superlightcar.com). Only such fundamental approaches will in future be able to provide the basis to argue and define realistic and sensible environmental legislation.

Jan 1, 2006

Results are presented of the investigation of gas dynamics of the blast furnace process obtained on laboratory models and operating furnaces. Gas residence times were measured using a helium tracer technique developed for the purpose. Residence times were determined in furnaces of 1007 m3 and 1719 m3 and results used in the calculation of the burden parameters and to estimate the distribution of the gas flow along the furnace radius. The effect of tuyere injection of coal dust on gas distribution was also investigated and the advantage of continuous injection compared with intermittent injection is noted. The unevenness of gas distribution across the furnace area is found to correlate well with differences in the size analysis of the iron-bearing component of the burden. The mixing of the gas streams between the neighbouring raceways was studied. It is shown that in the central region of the furnace gases from every tuyere are mixed together, whilst in the peripheral regions mixing is more localised and includes only the sections consisting of five adjacent tuyeres. A solution is proposed to the problem of a theoretical evaluation of the critical gas velocity. A simple relationship between the Reynolds and the Archimedes numbers was obtained from which, after substitution of the burden size data and the gas parameters, it is -possible to evaluate the critical gas velocity. Conclusions include information relating to the optimisation of the gas distribution and views on reducing gas injection at elevated furnace levels.

Jan 1, 1975

By Tarvainen M, Mattila O

Outokumpu Oy has systematically developed the automation of mineral flotation covering the technology of both new devices and control methods, and as a practical result of this effort currently produces two on-stream X-ray analyzers. The Courier 300 system basing on conven- tional X-ray technology is applied to complex or large processes. The newer Minexan 202 dis- tributed probe system based on radioisotope technology is developed mainly for simple or small scale applications. In this paper aspects and experiences of these analyzer systems and their applications for flotation control are discussed with particular reference to the role of the computer

Jan 1, 1977

By Tsuchida N

The history of world nickel production has been affected significantly by the supply and demand situation and fluctuation of LME price of nickel metal. In the beginning of the 1980s, the decline of price and demand lead to the withdrawal of un-competitive producers and the shrinkage of the production capacity. During the same period, Sumitomo Metal Mining maintained the production level with continuous improvement of the traditional matte electrorefining process. However, Sumitomo has recognised that the continuous improvement alone does not promise us the ability to catch up with rapid changes in the world. In the meantime, Sumitomo intensively researched chloride hydrometallurgy and has developed the chloride process for the nickel refining. This includes the solvent extraction and chloride electrowinning in the mixed sulphide process and the chlorine leach of the anode slime arising from matte electrorefining. In the late-1980s, Sumitomo Metal Mining decided to develop a new nickel refining technology based on chloride hydrometallurgy. The new process was designed from the comprehensive aspects involving safety and the environment. Construction of the plant for the matte chlorine leach electrowinning (MCLE) process was commenced in 1991. The MCLE plant with a capacity to 2000 tonnes per month has been commissioned at Niihama since 1992. The process has provided high productivity, overall good economics and high quality of electrolytic nickel produced. After the establishment of the process, Sumitomo has maintained continuous improvement of the new process and has attained the best practice of the work classification.

Jan 1, 1996

The results expected from a longwall face can best be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the effective operating hours, and the utilisation.The effective operating hours are determined by a number of scheduling factors which include the proportion of manned time to calendar time, the effective shift factor (effective time to manned time) and the move times.Analysis of the results achieved on the last 121 completed longwall panels in Australia (1984 onwards) shows a significant trend between 'actual tonnes/manned hour' and 'ideal production rate' (the measure of the capacity of the installation).Using 1982 'state of the art' longwall equipment, (the average in use in the seven year period), it should be possible to produce around 2.7M tonne/year ROM from a mine with one longwall. Few mines are achieving this.A review of production scheduling factors and general natural hazards affecting some mines suggests three things.1. Whilst some increase in average effective hours has followed the CIT decision, further improvement is possible at many installations.2. Many mines subject to general natural hazards, such as high gas make and high general stress, have found effective solutions and achieve the same utilisation as the overall average.3. A small number of faces within such mines have been severely affected, some less so. The most severe effects of natural hazards appear to be very site specific. This emphasises the need for detailed investigation of the causes, and development of means of predicting their presence. Only then can either satisfactory technical solutions be found to overcome the problems or prior decisions be chosen not to mine badly affected panels.

Jan 1, 1991

In the 25 years since Broken Hill's 75th Anniversary which was marked by an Australasian Institute and Mining and Metallurgy Conference in Broken hill, there have been some significant changes in the role of mines inspectors. This paper updates the information given by the then Chief Inspector of Mines, J.H. Burford, to that 1968 Conference, with an emphasis being placed on mines inspection, although it also reflects changes to mining legislation and regulatory bodies.

Jan 1, 1983

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

An Investigation on the Effect of Chrysotile Particle Shape and Anisotropic Properites on the Rheology of Chrysotile Suspensions Chrysotile, a polymorph of serpentine, is a phyllosilicate mineral that occurs as a major gangue mineral in many ores (eg Mt Keith nickel sulfide ore, Western Australia). The rheological behaviour of chrysotile stems from two main factors: its distinctive morphology and its electrical surface charge. It is believed that these factors are central to the problematic rheological behaviour and low solids throughput typically experienced in the processing of such ores. In this work, a study of the effects of chrysotile surface charge properties and particle shape on the rheology of chrysotile suspensions was conducted. It was found that the rheology of suspensions of pure chrysotile is characterised by extremely high yield stress values over a broad pH range (pH 4 to 11).The disparity in the point of zero charge and range of maximum yield stress for chrysotile is consistent with the anisotropic nature of chrysotile particles. A comparison of the rheological behaviour of quartz suspensions (non-fibrous) to that of chrysotile suspensions (fibrous) provides a practical indication of the effects of the fibrous nature of chrysotile relative to non-fibrous minerals. The long, thin fibres are easily entangled to form suspensions with much higher plastic viscosities and Bingham yield stresses than non-fibrous particles. Chrysotile particle shape and surface charge are central to the rheology of chrysotile suspensions, although shape appears to play a more significant role in this regard. This fundamental study would be beneficial to the ongoing research for improved recovery in the Mt Keith nickel sulfide ore as well as other chrysotile bearing ores.

Sep 13, 2010

This article attempts to outline essential features of the Mount Isa ore deposit, to reveal the agencies thought to be responsible for its localization, and to describe methods used for obtaining and applying geological data on a commercial basis. Structural features are emphasized because they have proved the most useful agencies to date in searching for ore. Vertical depth, horizontal width and stratigraphic thickness are used throughout the article, and quantities are quoted in long tons.THE DEPOSITA width of more than two miles of evenly bedded shale of the Mount Isa series (upper pre-Cambrian) lies sandwiched conformably between quartzites. The series strikes N.S. and dips approximately 60° W. Shale is unaltered...Important geological work has been carried out by the Queensland Geological Survey, chiefly by Mr. S. R. L. Shepherd, in co-operation with the Geological Department of Mount Isa Mines Limited. Selected references are The Queensland Government Mining Journal for December, 1931, January, 1932 (Rio Grande Lode); December, 19B2 (Black Rock Lode); October, 1933 (General structure); October, 1936 (Mount Isa Lode).

Jan 1, 1939

A paper presenting the results of studies carried out on rotary drill bit life at EluraMine N.S.W.Contributing parameters, including dataon drill operation and geology are compared to the performance observed for the drill bits. Correlation and performance characteristics are presented, relating this data to cutting size distribution over drilling depth.Details are presented of experiencegained through the operation of rotary drillsat Elura.

Jan 1, 1985

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988

Lake Kopiago is located some 71km northwest of Tari in the Southern Highlands Province and lies on the northern edge of the Papuan Fold Belt. The area is underlain by middle Miocene carbonate and fine grained clastic sediments intruded by late Miocene hornblende gabbros.Two mineral deposits occur to the south of Lake Kopiago. These are the Bisamu gold prospect and the Wunaki zinc-lead gossan.The Bisamu deposit consists of a calcic skarn assemblage which is geochemically anomalous in gold, silver, copper, zinc, cobalt, bismuth and tellurium. The prograde mineral assemblage includes garnet, clino-pyroxene and epidote whereas the retrograde assemblage includes epidote, quartz, actinolite and chlorite. Pyrrhotite is the dominant sulphide with minor pyrite and marcasite and trace chalcopyrite and sphalerite. Minor magnetite is also present. The Bisamu skarn shows many of the features typical of gold-skarn type mineral-isation.

Jan 1, 1994

Rehabilitation, reclamation and restoration are all terms used to describe the repair of land after mining. Here, restoration is used to mean restoring the land's original use, capability or productivity. Effective restoration is dependent on good planning before mining commences and must include a clear definition of post-mining objectives. The physical condition of the land within the mining licence was that of an imperfectly drained soil in permanent pasture, supporting a seasonal supply dairying unit. During the mining process, the soil layers were separated, with the topsoil stockpiled separately. As part of the restoration process, the land was recontoured to encourage surface drainage, with topsoil spread evenly over the recontoured tailings. Low grond pressure machinery was used to minimise soil compaction, with light discing and harrowing used to increase water infiltration. A permanent pasture was sown, with weed species controlled by spraying, both before and after pasture establishment.  Soil testing has been used extensively to ensure there were no nutrient deficiencies that good compromise pasture establishment and performance. Controlled grazing practices were used to ensure that the sown pastures became well established.

Jan 1, 1998

The Cleveland Mine has an annual ore production of 400,000 tonnes at a grade of 0.79 per cent tin and 0.30 per cent copper. It is achieved by an open stoping method, mechanised overhead sub-level benching. The operation is trackless with a ramp access from all working places to the surf- ace. Broken material is loaded from the stope and development headings into diesel trucks and hauled to the surface crushing plant.

Jan 1, 1977