Search Documents

By S Arya, A Bhandari

Dust emissions by blasting are of concern to both mine operators and surrounding communities. The quantity of dust produced, and the effects of its dispersal depend substantially on geological, blasting and meteorological conditions. This paper provides details of methods used to quantify the amount of dust produced after collecting samples using high volume dust samplers, and the difficulties encountered in satisfactory dust sampling and quantification. Also described are practical dust reduction methods by using water filled ampoules and water filled balls.

Jan 1, 2004

At 11 p.m. on Tuesday, 24th July 1979, an explosion of methane gas in a three heading development panel at Appin Colliery resulted in the deaths of fourteen men. The explosion followed after or was asso- ciated with a changeover of the ventilation to achieve a central intake between two returns. Investigation by Inspectors was followed by separate Judicial and Coronial Inquiries. Investigational information aimed at understanding the circumstances of the ex- plosion was prepared for the Inquiries. Recommendations following the Judicial Inquiry have been adopted by the Department of Mineral Resources.

Jan 1, 1981

Electrochemistry Measurement, Using Chena Analyser, to Investigate Selective Separation of Pentlandite and Pyrrhotite

Sep 13, 2010

FREQUENTLY the Survey Department is caIled upon to estimate the quantity of material in various dumps, dams piles, etc... and in the carrying out of this work various methods may be employed.The method used will vary according to the particular case in hand, and factors such as accessibility of the top of the dump, steepness of its sides, height, and the condition of the material to be estimated. A certain amount of "give and take" must be adopted in the treatment of small local cavities and mounds.In all cases it is desirable that the surveys made should be tied on to the lease surveys for the purpose of location, and that all levels should be reduced to the mine datum. It is also desirable to obtain levels of the original surface before deposition of the material to be estimated. If these have not been obtained beforehand, levels and transfers round the top will be the next best. If space is availabIe, flat surface is chosen as a site for the dump, etc. This is of the utmost importance in those cases where the material will have to be...

Jan 1, 1925

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By W G. Rowley

The Fortescue Metals Group story began in 2003 with a vision to establish an infrastructure project that would connect the stranded iron ore deposits of the Pilbara region of Western Australia with the steel mills of Asia. Following exploration successes in the Chichester Ranges using their new exploration model, Fortescue established significant iron ore resources at Cloudbreak and Christmas Creek during 2004 and 2005. By May 2006 the definitive feasibility study for mine, rail and port was completed, many of the key government approvals had been obtained, product development and market acceptance were complete and 1.07 Bt of total proved plus probable iron ore reserves were defined to support a 20 year mine life from the Cloudbreak and Christmas Creek deposits. Project construction commenced in September 2006 following a successful $3.2 billion capital raising. By April 2008, the mine and processing plant at Cloudbreak were completed along with the Herb Elliott port facility at Port Hedland and 256 km of heavy haul railroad linking the mine with the port. Mining of overburden commenced at Cloudbreak in late 2007 and by 15 May 2008 the first shipment of iron ore had departed for China. In the first 12 months of operation total shipments amounted to 24.6 M wet metric tonnes with weighted mean composition of 58.9 per cent Fe (64.4 per cent Fe calcined), 4.3 per cent SiO2, 2.0 per cent Al2O3 and 0.047 per cent P. Exactly 3.5 years between the Cloudbreak discovery hole and commercial production. The project success depended on many technical breakthroughs including a new exploration model, application of the surface miner as the main mining production unit, design of a new marketable fines product called æRocket FinesÆ, a highly efficient ædesandÆ flow sheet for upgrading of 2.4 per cent alumina run-of-mine to 1.9 per cent alumina Rocket Fines, 40 t axle loads for the heavy haul railway and a high capacity-highly automated port facility.

Jan 1, 2009

By A Murphy

Mining plants and infrastructure, and the decisions made by their designers, can have large impacts on their environmental and social context, commonly referred to as the site or plant footprint. They can also be the source of constructive contributions to sustainable development when designers are enabled via the information, systems and tools to incorporate sustainability in engineering processes. A facility’s footprint and the project’s contribution to sustainability – economic, environmental and social aspects – are now key considerations in regulatory approval processes and are the fundamental drivers of support, or opposition, from the project’s stakeholders.Historically, plant and infrastructure designers have not been well integrated with the environmental and social professionals who are engaged to pursue regulatory approvals. Despite this, many objectives central to technical and process engineering have in fact contributed positively to a facility’s footprint and indeed its contribution to sustainable development. Examples of these objectives include increasing process and energy efficiency, and minimising the quantities of waste requiring disposal. With the framework of sustainability, mining plant and infrastructure designers are indeed at the forefront of incorporating sustainability into resource industry projects and are central to the process of obtaining regulatory approvals and ongoing stakeholder support. The process of incorporation starts with a shared understanding of sustainability and sustainable development, and continues with project processes that facilitate information and knowledge exchange throughout the project life cycle.CITATION:Murphy, A, 2014. Incorporating sustainability into mining plant and infrastructure design, in Proceedings Life-of-Mine 2014 , pp 637–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The impact of moves to introduce Abori- ginal land rights was felt in the Northern Territory as early as 1972 when the Federal Government froze the processing of all appli- cations for mining interests over vacant Crown land. The Aboriginal Land Rights (Northern Territory) Act was finally proclaimed on Aust- ralia Day 1977 and since that date the mining industry and the Territory legislature have struggled to make the Act work. Despite these efforts long delays have been experienced by those required to negotiate mining and explor- ation agreements under the Act. In fact explor- ation on Aboriginal land has been effectively stiffled since the introduction of the Abori- ginal Land Rights Act. The Northern Territory government and the mining industry have both sought amendment to the Act to remedy some of its more onerous problems. These efforts have generally been fruitless. Some of the recommendations put forward by Mr Justice Toohey following his recent review of the Act would provide relief in some important areas. However, any such improvements are more than offset by a number of Mr Justice Toohey's recommendations which would severely disadvantage the vast majority of Territorians. A recent survey of mining companies seeking exploration licences over Aboriginal land indicates that many of the existing diffi- culties could be overcome without significant amendment to the Act but rather by the adoption of a positive administrative approach by the Land Councils. It is now up to the Commonwealth and the Land Councils to demonstrate that their Act can work without crippling the Northern Territory economy and its mining industry.

Jan 1, 1984

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

By Moinpour M

The kinetics of reduction of copper (cuprous) sulphide with CO-CO2-He gas mixtures, using an excess of CaO(s) as a sulphur-scavenging substance were investigated in the temperature range 855° - 950°C by a thermogravimetric method. Several gas compositions were employed at each temperature. Potential carbon deposition was overcome by preheating the reducing gas mixture. The phase-composition and the morphology of partially reactedsamples were analysed by a SEMlEDAX unit. The reduction rates showed strong dependence on the bulk gas compositions (CO, CO2) and, in most cases, the rate declined with rising temperature. The rate-controlling step appears to be the diffusion of CO2 gaseous species through the micropores of the CaS(s) - product layer which builds up around the CaOcore.

Jan 1, 1989

The Wattle Dam gold mine, located near Kambalda in the Goldfi elds region of Western Australia has recently progressed to an underground operation and is now believed to be Australia's highest grade operating gold mine. At end of March 2010, the deposit had reserves of 132 000 t @ 20.8 g/t for 88 000 oz and by the end of June 2010 had produced 110 000 oz from open-pit and underground mining. The Wattle Dam main lode is characterised by very coarse gold mineralisation. Gold occurs as cm to decimetre fracture fi ll veinlets, shear surface coatings and erratic fl akey clusters. The gold has no quartz or silica association and lacks adjacent low-grade mineralisation or alteration assemblage. Geologically it appears atypical of Archaean lode gold deposits and may represent an extreme end member of the type. Definition of the lode is largely dependent on effective geological identification of the host lode zone and an understanding of the erratic distribution and grade behaviour of a high-nugget, coarse gold deposit. Dependence on assay data to defi ne the lode zone would result in the deposit being mined incorrectly and much of the deposit being left unexploited. This paper discusses the geology, coarse gold characteristics and defi nition methods which are used to successfully defi ne and mine the deposit.

Aug 1, 2010

By P C. Couper, P C. Keall, S J. Mathews, A Francis

An epithermal gold-silver deposit is presently being developed at the Golden Cross Mine in the Waitekauri Valley, 8 km northwest of Waihi, New Zealand. Highest grade mineralisation underground is mainly confined to an elongate zone of strongly banded quartz veining on the hangingwall. Footwall veining is irregular, flatter lying, and of lower grade. Hydrothermal breccias in the ore zone may have economic grades where clasts of vein quartz are present. Jigsaw breccias, shingle breccias, and layered breccias with sedimentary type structures such as layering, crossbedding, and graded bedding have been identified proximal to, and within, quartz veins. Mineralisation in the open pit occurs in and adjacent to stockwork quartz veining.   Three alteration zones are recognised: a central silicic zone enclosing Au-Ag bearing quartz veins, an argillic zone above the stockwork zone and in the footwall of the underground ore zone, and a propylitic zone which is gradational with argillic zone. Intense shearing is confined to the less competent argillic zone.   Precious metal mineralogy consists of electrum (65% Au; 35% Ag) and argentiferous tetrahedrite, polybasite, pyrargyrite, argentite, and native silver. Pyrite is the dominant sulphide mineral. Marcasite, arsenopyrite, and rare chalcopyrite and sphalerite also occur. Oxidation ranges from a few metres in the argillic western stockwork zone to 100 m in fractured rock in the footwall of the stockwork.   The open pit contains a proved and probable reserve of 2.1 million tonne grading 3.5 g/t Au and 17 g/t Ag. The underground mine will produce 2.7 million tonne grading 7.8g/t Au and 27g/t Ag.

Jan 1, 1991

By B E. McCarthy

Red Dome Mine was a highly complex gold copper operation developed over a number of phases between mid-1986 to October 1997. With only three years of production ahead at any time, a proactive practical approach to mine closure was necessary. In 1989 the Domains Concept to life-of-mine planning and mine closure was created as a response to the proposed changes to legislation.The Domains Concept, a relatively simple idea developed to integrate mine closure during production at Red Dome, has been broadly adopted by both government agencies and industry in the intervening 20 year period. Over time the author has observed that the concept has been poorly applied, misunderstood and in some cases even misrepresented. As a consequence, the potential opportunities from applying the concept, including the optimisation and minimisation of life-of-mine costs, mitigation of long-term financial liability exposures and building credibility with the general community, have been missed.This paper examines the many benefits, advantages, applications and perceived barriers to developing and integrating a fully costed life-of-mine plan. Integrating the Domains Concept early in the project, within the operational budgeting, allows the production of a meaningful and useful document, representative of a whole life-of-mine, cradle to grave, with measurable rehabilitation and closure outcomes when the concept is used to full effect.The Domains Concept serves to optimise cost-effective, whole of mine, life cycle planning which provides beneficial outcomes for the community, significantly mitigates legacy issues and contributes to the attainment of compliance and sustainability principle objectives.CITATION:McCarthy, B E, 2014. The domains concept – 20 years on retrospective, obstacles and opportunities for effective life-of-mine implementation, in Proceedings Life-of-Mine 2014 , pp 621–636 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Leahy G. J, Moxon N. T, Nicol S. K

Experimental work is described in which extremely dilute aurocyanide liquors are treated with novel surface-active complexing agents to produce a hydrophobic aurocyanide species. Subsequent aeration of these liquors causes accumulation of such species at the air-water interface and the aurocyanide complex is transferred to a froth concentrate. A detailed performance assessment of this process is made and this knowledge used in the design of a pilot plant facility. Early results indicate the feasibility of the selective recovery of aurocyanide ions from reclaimed residue dam water (approximately 0.2ppm Au) with upgrade ratios of the order 180:1. A further study was made applying ion flotation to the recovery of gold from a carbon-in-pulp (CIL) feed liquor (approximately 1.0ppm Au). The probable economics of this process compared to conventional CIL processing is also described. Successful development of countercurrent ion flotation for concentrating solids-free gold solutions may offer a lower cost alternative to existing gold ore processing technologies, or in more secondary applications such as concentrating dilute gold solutions or heap leach runoff. The technology may also have more generalised applications to other heavy metal process- Ing.

Jan 1, 1991

Two recently published studies have considered whether and how robots, which have been designed for manufacturing applications, could find use in mining. The conclusions of both studies, if not identical, are compatible. Automation of mining activities will continue. Robots, at least in the short term, will have little application in mining. However, robotic concepts, both hardware and software, are of considerable relevance to mining automation, and can be anticipated to diffuse gradually into mine environments. The present paper is intended to convey the current state of thought on this subject to IFAC Symposium participants who may be unfamiliar with the referenced studies, and is not intended to report previously unpublished research.

Jan 1, 1985

Patterns of successful metallic mineral discoveries in Australia are analysed for the last three decades. A trend towards more discoveries of poorly expressed and blind ore- bodies is evident and can be expected to continue. Discoveries using traditional and conceptual geological techniques have proportionally declined but are expected to continue at a significant level for a decade or so. Improvements in the quality and numbers of geological exploration models and in the quality of available basic geoscience data have aided successful discovery in recent years. Although some orebodies for the Year 2001 have already been found maintenance of a strong mineral inventory demands that more and better geological models are applied. Empirical models need to be improved by critical multi- disciplinary integrated studies of mineral occurrence at all scales. New models can and will be developed by various means. If application of these models is made with all the innovation, initiative and unorthodoxy that can be mustered then new discoveries will result. Greater attention to the surface expression of orebodies will also lead to new discoveries. Review and follow-up of old data in the light of new concepts will provide yet another discovery route.

Jan 1, 1981

A pilot steel ladle injection facility designed to assist in the production of high quality steels suitable for use in pipelines has been built and commissioned at the Basic Oxygen Steelmaking (BOS) plant at Port Kembla Works.The plant design and the injection procedure are described.The performance of the unit and some metallurgical results are discussed in terms of the addition to the steel ladle of various quantities of calcium silicide and a lime based material. The effects of these additions on sulphur content and inclusion morphology and hence on steel ductility are also presented. The influence of ladle lining on desulphurisation is illustrated.On the basis of the experience gathered in the pilot plant a permanent and more sophisticated injection facility has been designed.

Jan 1, 1983

The poor reconciliation between the values of estimated and actual grades can cause major economic losses to the mining industry. In a mining operation grade reconciliation is comparing the values of estimated grade calculated in exploration stage with actual grade obtained from blastholes' data. Many different factors affect the degree of reconciliation in a mining operation. In this paper we investigate the factors related to estimated grade which affects the reconciliation process in the exploration stage of the orebody. These factors are the sources of uncertainty in the rest of mine life. In this area the most important factors are inherent variability, statistical uncertainty and systematic uncertainty. A probabilistic model was presented to model each source of uncertainty. The implementation of proposed model was checked and its validity was investigated using real data in an iron open pit mine in Iran.

Dec 6, 2010

By P N. Nkrumah, A van der Ent, G Echevarria, P D. Erskine

Nickel phytomining is a low cost alternative to traditional nickel mining and a complementary process to existing mining operations in areas with low-grade nickel soils or nickel waste material. The process of nickel phytomining consists of growing selected hyperaccumulator plant species (‘metal crops’) on Ni-rich (ultramafic) soils, followed by harvesting and incineration of the biomass to produce a ‘bio-ore’ from which Ni salts or Ni metal may be recovered (Chaney et al, 2007). The ‘metal crops’ are selected on the basis of high biomass yield combined with high Ni concentrations (>1 per cent) in the above-ground biomass (Chaney et al, 2007). Currently, Alyssum murale and A. corsicum have been used for Ni phytomining trials, mainly undertaken in Albania and USA (Bani et al, 2015; Li et al, 2003), while the agronomy of <10 species has been tested in temperate regions (Nkrumah et al, 2016). Nickel phytomining has high economic potential; however, large-scale demonstrations are needed to provide ‘real-life’ evidence for commercial operations (van der Ent et al, 2015). Unrealised opportunities exist in tropical regions for commercial scale Ni phytomining. To date, the agronomy of tropical ‘metal crops’ has not been tested. This extended abstract presents the progress of tropical phytomining, and reports on agronomic trials undertaken to determine whether the trends in temperate regions could be confirmed in a wet tropical environment.CITATION:Nkrumah, P N, Erskine, P D, Echevarria, G and van der Ent, A, 2016. Progress in tropical nickel phytomining, in Proceedings Life-of-Mine 2016 Conference, pp 135–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

XstrataÆs Mount Isa Copper Operations (MICO) is a world-class mining operation producing in excess of six million tonnes of copper ore per annum from its underground mining operations. The Mount Isa Copper Mines have been producing from the underground operations since 1952. Current copper reserves are 87 million tonnes at 2.8 per cent Cu, extending the mineÆs life beyond 2018. The underground orebodies in the copper mines are divided into nine distinct areas and are mined by sublevel open stoping techniques. One of the nine areas is the hanging wall lens, which consists of two sections; a northern lens (NHWL) and a southern lens (SHWL). The SHWL has a proven reserve of 2.2 million tonnes with an average grade of 2.9 per cent copper. Stopes in the SHWL have an average size of approximately 245 000 tonnes and will be extracted in a primary-secondary mining sequence, producing ore until 2009. This paper discusses various aspects of stope design applied in the southern hanging wall lens, including sequencing options and the rationale for the selected sequence. Design features are also discussed and how they have evolved as more is learnt about the SHWL orebody. These include mass firing techniques, focusing on minimising ground vibrations, using seed wave form analysis and prediction. Rock mechanics issues will also be discussed, in particular the reinforcement of stope hanging walls and the use of instrumentation to monitor behaviour within the hanging wall.

Jan 1, 2006