Search Documents

When lying over 200-250m depth, many seams and surrounding strata are gassy enough to create mining difficulties , particularly in highly productive longwalls as well as in their development headings. In addition to the gassiness of seams or stra- ta in the outgassing volume around working, the shape expansion and limits of this one influences much the intensity of gas emission. These charac- teristics of outgassing volume differ very much ac- cording to the permeabilities of the seams and strata encountered by their fracturation due to mi- ning. Moreover, the shape of the outgassing volume is very much modified by the rate of advance of the face. In nearly impermeable deposits, gas flows from a limited outgassing volume. When the rates of advance of a face are medium or low, the shape and dimensions of this volume do not change very much and outgassing volume is translated progressi- vely with the face advance. This explains why, in the past, it was observed that there was for each seam an average steady specific emission of gas, round which the volume of gas evolved per mined ton or per mined unit area, calculated over a cer- tain time, was oscillating. Combined with a statisti- cal irregularity coefficient, this allowed prediction gas of emission and thus to take decisions for air ventilation, drainage, and eventually production.

Jan 1, 1988

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

By I M. Platten, Y Xie

Complex gold deposits are generally characterised by variable geometries, strong structural controls on grade distribution and a high-nugget effect. The use of diamond drilling and fire assays in this environment often results in an understatement of grade. Bulk samples are likely to be the closest estimators of true grade, and may be required to evaluate geological/grade risk during resource estimation/feasibility studies. Any bulk sampling program requires appropriate planning and implementation. The planning stage should attempt to delimit the extent and nature of mineralisation; characterise mineralogy and metallurgical properties of the ore; and define bulk sample size and how it will be sampled/processed. The approach to sample processing will be governed by the results of metallurgical testing and geological knowledge. Careful design of sampling protocols must be undertaken through material characterisation, understanding of gold particle sizing and the application of GyÆs Sampling Theory.

Jan 1, 2008

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

By D von Horn

Mineral sand orebodies are typically mined for their TiO2 content. Increasingly over the past 30 years, the major mineral focus has shifted from natural rutile to ilmenite and an acceptance that the latter generally needs some form of upgrading for economic conversion into TiO2 pigment. This upgrading obviously has a cost, and in conjunction with diminishing mineable feed grades, results in higher cost TiO2 units for chloride route Pigment Plant feedstocks. The net cost of feedstock can be significantly influenced by the recovery and sale of accessory minerals and by-products from the processing chain to the extent that some producers have the potential to achieve a zero net cost. Whilst slagging plants typically reduce net cost from rutile, zircon and pig iron revenues, operations supporting Becher type synthetic rutile operations have been limited to revenues from rutile and zircon only. A range of alumino silicate minerals show industrial potential, as does activated carbon, iron oxide and gypsum, by-products of the synthetic rutile process. Tiwest is a good example of a company maximising revenue from the accessory minerals as well as from by-products of the synthetic rutile process.

Jan 1, 2001

As a result of the world depression and the consequent heavy fall in the price of tin, Malaya joined with other great tin producing: countries of the world in a restriction scheme that heavily restricted production from its individual mines. This condition, together with the knowledge that it was becoming more and more difficult in, Malaya to acquire further areas and so prolong the existence of a specific company's activities, induced Mr. H. G. Scott, managing director for the Siamese Tin Syndicate Ltd., to consider other possible sources of production. Mainly because of the conditions that obtained in Tasmania, he turned his attention to that country, where, not only could mining be carried on without restriction as to output, but where the incidence of the exchange position created favourable conditions for operation. The district selected for examination was that of St. Helens, on the East Coast of Tasmania, which district had behind it a long record of successful tin mining operations.PRELIMINARY OPERATIONS OF SIAMESE TIN SYNDICATE LTD. AT ST. HELENS.First of all the district was examined, and there was no lack of evidence to show that tin existed, although it was impossible to get down to quantities and values without an extensive prospecting campaign. For one thing, the physical features of the country seemed to be all wrong. There were no extensive alluvial flats such as a mining engineer...

Jan 1, 1934

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940

By T Graham

The invention of the traditional belt and idler conveyor system is attributed to Thomas Robins in 1892. This basic concept, ubiquitous in most mining operations, has not changed markedly in 125 years and still suffers from five forms of energy losses. Firstly, Wheeler, Roberts and Jones (2004) showed that indentation rolling losses, a consequence of the indentation a roller inflicts on the belt, consume 60 per cent of all energy. Secondly, Wheeler (2006) explained that bulk solid flexure resistance resulting from material interaction and movement absorbs 20 per cent. The remaining energy is lost by idler rotating resistance (5 per cent), belt flexure resistance (5 per cent) and secondary resistances (10 per cent).Traditional conveyor systems are continuous as opposed to batch systems, implying both positive and negative features. On one hand, continuous systems have high availability (available infers ‘ready to run’), but, on the other, utilisation of availability is often low; for example, when a conveyor is running empty or below capacity. This converts into reduced system OEE (overall effective efficiency). Many attempts have been made to mitigate energy losses and low OEE issues, including development of rail-based systems. The key drawbacks have been higher capital cost, low flexibility, poor availability and lack of market acceptance.A recent conceptual development known as the ‘autonomous rail conveyor’ (ARC) promises to address issues of energy loss and poor availability and provide increased flexibility by offering solutions for difficult applications. The ARC uses a series of interconnected skeletal bogies covered with a conventional conveyor belt as a load bed running on relocatable light rail. The bogeys have two axles, each driven by integrated variable speed-geared motor and brake systems, and are connected to previous/next bogeys by specialised couplers. Power is provided by a generator (located in a dedicated bogey) and ‘daisy chain’ plug in cables. Centralised redundant control is provided at a preferred point. Although the system is batch in nature, the number of carriages and trains is flexible, meaning that the system is effectively continuous. Loading is achieved by feeding the ARC from a perpendicularly oriented apron feeder, while material off-loading is accomplished by a twist-dump operation in which the belt is twisted through an angle of 50° below the horizontal, causing material to flow from the belt into a receiving conveyor.The ARC system can run multiple trains over any distance, although benefits are more significant in distances of over two kilometres. Capital and operating costs are predicted to be lower than competitive products, with planned maintenance being simple to perform.CITATION:Graham, T, 2017. The autonomous rail conveyor significantly reduces ore haulage costs, in Proceedings Iron Ore 2017, pp 467–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By T A. Carter

In 2010 Agnew Gold Mine (AGM) struggled to produce the required tonnages from its stopes. The longhole rises used to create void in stopes were unreliable and often failed to gain the designed rise height. The number of firings per stope was having an adverse impact on the ground conditions at the stope brows, impeding stope productivity.Through practical experimentation with longhole drill rigs, box hole rigs and development drill rigs as well as trialling new methods in conjunction with reviewing drill hole data, drill hole accuracy was observed to be an issue on-site. Innovative dragging methods such as the reverse drag, combined with a slope instead of a vertical face on the rear of stopes, have improved dragging and a reduction of firings per stope, enabling larger production blasts.The methods trialled and subsequently implemented at AGM have facilitated the mine achieving budgeted targets for six consecutive quarters. This paper documents the use of these methods in a key lode of AGM’s operations to improve drill and blast practices in order to achieve production targets.CITATION:Carter, T A, 2014. Improving production drilling and blasting in the Kim South orebody at Agnew Gold Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

By Mukherjee R, Bandopadhyay S

Three applications of fuzzy logic in mineral exploration show the possibility of providing feasible solution and allow greater freedom in decision-making processes for geoexploration data which may be ill- defined, biased or where apriori infor

Jan 1, 1998

Continuing education is recognised as an essential aspect of professional training, but no systematic procedures have hitherto been attempted. The tertiary educational institut- ions are making a valuable contribution without formal financial support. The Australian Mineral Foundation is offering a programme of continuing education in the earth science and related disciplines both by direct initiative and by co-operation with existing tertiary educational institutions.

Jan 1, 1974

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

By B Beamish

"All underground coal mines in Australia are required to develop a Spontaneous CombustionManagement Plan (SCMP). The New South Wales Government has developed a guideline (MDG1006) to assist operations to comply with this requirement. A reference document is alsosupplied with the guideline that describes the type of information that is needed for input to theplan, including identifying possible tests that can be used for propensity assessment. However,there is no clear indication of what program of sampling and testing is suffi cient to provide adefi nitive assessment of spontaneous combustion propensity prior to and during mining. This paper reviews the existing methods available for quantifying spontaneous combustion propensity and discusses the sampling requirements that are needed from exploration to mining. A new, more defi nitive method of spontaneous combustion testing is also presented that benchmarks coal self-heating performance from mine ambient temperature to thermal runaway. Examples of the eff ectiveness of this new test method for identifying and quantifying reactive pyrite in coal as well as quantifying the diff erence between dry and wet season conditions are provided in the paper."

Jun 1, 2012

Mechanism Responsible for Flocculation in Poly (N-Isopropylacrylamide) Temperature Responsive Dewatering - Attractive Interaction Forces Induced by Surface Hydrophobicity

Sep 13, 2010

By D Ryan

Following a long period of increase, there has been a reduction in exploration expenditure and activity in Australia over the past two years. During the post Second World War period, exploration was largely driven by mining companies seeking resources to satisfy an increase in world demand, while increasing their asset base as a result of mineral discoveries. In general, return on investment to shareholders was not the major driving force. With the exception of gold the mining industry has been faced with a long-term fall of metal prices in real terms. As a result the net profit return on average shareholderÆs funds in the Australian minerals industry has fallen from over 20 per cent in 1990 to less than five per cent today. Mining is now competing for funds with communication and finance based industries yielding high returns on shareholder investment. Shareholders and superannuation fund managers seeking a high return on short-term investments have indirectly reduced the funds available to the mining industry. Globalisation of the mining industry is leading to the rationalisation of the Australian mining industry as witnessed by mergers and acquisitions of local companies by foreign investors. The return on capital invested in the Australian mineral exploration industry must improve if the industry is to be competitive on a worldwide basis. Failure to achieve this will result in capital flowing overseas or to other industries. Relatively short-term upswings in metal prices which are generally driven by threats to the supply base (eg strikes, mine closures, increases in country risk) often lead to increased capital raisings for exploration funding. As a consequence of the time taken to raise the capital and increase exploration activity, measured exploration activity lags the metal price increases. There are also lags between commencement of exploration and discovery and ore production. In the case of gold exploration expenditure peaked six years after the price rise of 1980 Companies persevering with exploration in the current difficult period will be rewarded because they will be able to capitalise on future metal price rises and a minimised time lag.

Jan 1, 2000

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

By K Nilsson, D Connelly

Troy Resources acquired the Karouni Gold Project in Guyana, South America in 2014 and immediately proceeded to a Pre-Feasibility Study and project implementation. The study considered two open pit mines feeding a conventional carbon in leach (CIL) gold plant with a capacity of 1Mtpa. The study assumed a total of 2.61 million tonnes of ore with an average grade of 3.84 g/t gold with a recovered gold production of 303,526 ounces over a three year mine life.The project development involved drilling metallurgical test holes, securing second-hand major pieces of equipment where suitable, and arranging shipping to Guyana. The remote location meant logistical considerations were paramount. The plant consists of conventional two-stage crushing with single stage ball milling and a gravity circuit. The tailings circuit includes DETOX.The extremely high rainfall presented challenges with water management and the necessity to dispose of clean water to the environment. The DETOX was also mandatory due to the highly sensitive environment and past history in the area. The criticality of this meant that in the design, any cyanide in the tailings would precipitate in a plant shutdown.Lessons were learned and the project has been both profitable and successful for Troy Resources in a new operating location. In addition, the project has created jobs, delivered royalties and brought new skills into an area where previously there was little current mining activity.CITATION:Nilsson, K and Connelly, D, 2015. Karouni Gold Project from drill core to commissioning, in Proceedings MetPlant 2015, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By A Garg

Squeezing can occur both in hard rock and in jointed rock mass as a result of over stressing. It is related to time dependent shearing, ie shear creep and is associated with the volumetric expansion (dilation) and radial inward displacement of the tunnel surface. While planning a tunnel in hard rock under a high cover of the order of 2 km it is desirable to identify the potential squeezing ground conditions and to select appropriate excavation technique and the support measures. There are several solutions to counter balance the squeezing ground viz over excavation of tunnel profile, assessing appropriate excavation technique, provision of a ductile primary support and time for providing tunnel lining. Low drivage rates and high cost due to support failures requiring rectification arising out of poor anticipation of tunnel closures and support pressures are major problems associated with tunnelling under squeezing ground conditions. Under squeezing ground conditions, the deformation will be gradual, therefore, in order to absorb deformations yielding supports are quite useful as primary support which provide a reliable low initial support pressure and permit uniform stress relief of the surrounding rock along with preventing rock from ravelling. The paper discusses the various factors which influence the selection of appropriate excavation technique and support measures in hard rock under squeezing ground conditions.

Jan 1, 1999

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964