Search Documents

By I Coombes, M Trim, Y Sun, M McRae, A Spiegl, H Lagger, A Amon, P Barraclough, M Villeneuve

The Brisbane Airport Link Project (AirportlinkM7) includes the design and construction of more than 12.5 km of tunnels, with the Kedron interchange including four ramp tunnels that intersect with mainline tunnels and result in caverns with spans of up to 26 m. These caverns are in highly variable ground conditions with less than 35 m of cover underlying residential neighbourhoods and commercial properties. The Kedron caverns were constructed using the sequential excavation method (SEM). Owing to complex geometry and excavation sequence, the caverns were designed based on numerical modelling methods, including both two- and three-dimensional models. These numerical methods were used to develop a suite of support types with excavation sequences for the expected range of ground conditions. A combination of methods that included in-tunnel monitoring (convergence monitoring and extensometers), probe holes, endoscope probes, face mapping and ground settlement measurements were used to verify performance of the tunnel support systems and to select and refine the appropriate support system for each section of the caverns. The construction monitoring data indicated that numerical modelling can provide a good basis for predicting the performance of large-span underground openings in highly variable ground conditions. This paper presents a comparison of the performance of the caverns predicted by state-of-the-art numerical models and the actual measured performance.CITATION:McRae, M, Villeneuve, M, Trim, M, Sun, Y, Barraclough, P, Spiegl, A, Amon, A, Lagger, H and Coombes, I, 2014. Brisbane Airport Link Project – design and construction of the 26 m span Kedron Caverns: comparing monitoring data with the design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By V Narayanaswamy

SustainabilityÆs imperative of economic development in tandem with social advancement and environmental protection is widely accepted, but much debate remains about the practical implications for the minerals processing technologies and practices for the future. Experience in other industry sectors however suggests that sustainability can be a value-adding framework for innovation in processing technologies, business models and management systems. This position paper explores how sustainability can drive innovation in minerals processing, by reviewing pertinent ideas and experiences gained in non-minerals sectors. Sustainable innovations can generally be broadly ranked from incremental to transformative, with each category having its own typical improvement potential, timescale and technological and operational challenges. This leads to a æmud mapÆ for sustainable innovation in minerals processing with three distinct tracks: eco-efficient operations; sustainable plant design and sustainable processing. Competing models for the sustainable innovation process through either forecasting or back-casting, have in common the strong reliance on vision, perspective and competency, which in turn highlights the importance of sustainability frameworks. Such sustainability frameworks provide normative goals and option elicitation prompts to assist with the analysis of current processes and scoping of more sustainable alternatives. A comparative analysis of five prominent environmental sustainability frameworks revealed three cross cutting sustainability themes that challenge current resource processing technologies and practices. These are: fate of materials (zero dissipation of materials); compatibility of materials and processes; and materials intensity of industrial products and processes. Although the sustainability concepts presented in this paper have not been extensively road tested in the minerals processing industry, there is ample evidence that recent initiatives in the Australian resource sector illustrate the applicability of the proposed framework. It is therefore argued that more in-depth assessment of sustainable innovation concepts would be a valuable contribution to the sustainable resource processing theory and practice.

Jan 1, 2004

Following GyÆs earlier proposals for the use of StudentÆs t-test, a simplified, effective method and philosophy are proposed to test for maximum tolerable bias in data sets as well as in sampling devices. The philosophy of testing is particularly emphasised to derive important practical implications in terms of decision-making and risk control. Conclusions are offered which should equally matter to manufacturers and users of sampling equipment.

Jan 1, 2005

By P Crittenden

Thiess Pty LtdÆs Australian Mining business unit used 7.6 PJ of energy in the 2007/2008 financial year. This represented more than 85 per cent of Thiess Pty LtdÆs total energy use and therefore meant that the Australian Mining business unit is required to conduct energy efficiency assessments and report publicly on the outcomes by December 2008 under the Federal GovernmentÆs Energy Efficiency Opportunities (EEO) Act. Thiess Pty Ltd has a policy commitment to sustainable development throughout its operations. This includes minimisation of its carbon footprint and the Australian Mining business unit has a strong focus on efficiency in all of its operations. It approached the energy efficiency assessment as an opportunity to further improve and build on its energy efficiency and greenhouse gas reduction focus in the business. As a mine contractor, Thiess faced a number of challenges in designing an assessment process that would be both effective and efficient to deliver. For example, unlike most other companies involved in the Energy Efficiency Opportunities program, the energy use associated with the Australian Mining business unit is not fixed to any single geographic location in Australia. Mining vehicles are moved from site to site according to the specific requirements of mine owners and the timing associated with the commencement and completion of contracts. Thiess departed from a traditional æsite by siteÆ based assessment and designed a ærepresentative assessmentÆ approach that involved detailed investigation of data across all sites and a focused assessment on a single site.Data and analysis was an essential part of the assessment and indicators at company, mine and site level were essential in identifying opportunities and tracking progress. Forty-six potential energy saving opportunities were identified and four of these are currently being implemented. The projects being implemented are: payload management, automating mobile lighting equipment, plant idle time management, and turbo idle downtime. The potential savings from the four major projects that have been identified are approximately 150 800 GJ/annum, equivalent to 10 600 tonnes of CO2-e/annum with a simple payback period of less than two years. Beyond the fuel savings however, there are a number of other benefits from the assessment, including operational efficiency, reduced maintenance costs and even a potential reduction in the number of vehicles required to complete the work. The EEO assessment has significantly increased the importance and urgency of energy efficiency and facilitated the sharing of good practice across all Thiess operations. Not only have four projects been adopted for immediate implementation but a further pipeline of projects is available for future possible implementation. This case study describes: how Thiess conducted its assessment including the use of energy data and indicators, the opportunities identified that are currently being implemented, and the lessons learnt and how other organisations can use these to improve their approach to energy efficiency assessments. This case study is a more comprehensive version of a case study developed for the Commonwealth Department of Resources, Energy and Tourism. The assessment results reported in this case study are drawn from the Thiess Energy Efficiency Opportunities Report 2008.

Jan 1, 2009

By Coulter K. W

The commercial evaluation of coking coal from bore core data will begin with a technical evaluation of the coal properties affecting coke quality. Methods currently used for prediction of coke.properties from coal analysis are illustrated but in each case accuracy of measurement and prediction should be clearly understood. It is suggested that coal be initially valued from coking properties (base value) and adjusted for chemical properties (merit value). Final evaluation of coal can only take place as coke in the blast furnace where the coke is assessed under high temperature operating conditions. The commercial value of a particular coking coal will depend on many additional factors other than the technical properties.

Jan 1, 1977

By Taylor L. M

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry. Some of the computer programs previously used to predict rock motion employed polygonal elements with comers and sides to model the rock (Cundall, 1971; Walton, 1982; Taylor, 1983). This approach allows the elements to bulk because of the corners and the aspect ratio. However, tracking the many interactions of the comers and sides of the elements is a computationally intensive process. Several other rock motion computer programs were developed that employed spherical elements, (Schamaun, 1984; Gorham-Bergeron et al, 1987) but they lacked correct bulking mechanisms or could not be vectorized for efficient execution on vector processing machines. A new spherical element code called DMC (Distinct Motion Code) (Taylor and Preece, 1989a, 1989b) has been developed this past year. DMC was designed and written to take advantage of super-computer vector processing capabilities. The efficiency has also been increased through the use of spherical elements, explicit time integration and a new contact search algorithm. When spherical elements were chosen for efficiency, some physically correct mechanisms for capturing the bulking behavior of the rock mass also had to he developed. This paper will treat several mechanisms that were developed to allow spherical elements to exhibit correct hulking behavior.

Jan 1, 1990

Rifting and transfer faulting in the Late Cretaceous to Early Tertiary resulted in the formation of the Bundaberg Trough and Wallaville Basin and deflected the margin of the Maryborough Basin southwestward between the Kolan and Burnett Rivers. During the Cainozoic, three periods of volcanic activity occurred in the Bundaberg-Gin Gin area. The oldest of these periods, Paleocene to Early Eocene, resulted in the outpouring of tholeiitic lavas. During the Late Miocene to Pliocene, undersaturated alkali basalts generated at depths of from ca. 35 to 55 km were emplaced. These lavas were followed in the Pleistocene by the alkaline Hummock and Berrembea Basalts. The loci of eruption of all of these lavas were controlled by the intersection of the transfer fault system and pre-existing north to northwesterly trending faults in the Bundaberg-Gin Gin area.

Jan 1, 1990

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

The paper gives details of the performance of a 6-ft. by 6-ft. grate discharge ball mill which was converted into a rod mill of the overflow type and then into a grate discharge rod mill. Proposals for further alterations are outlined.INTRODUCTIONThe mill of King Island Scheelite (1947) Limited recovers scheelite by gravity methods.Crushed ore at the rate of 34 tons per hour is divided between two mills. (6 ft. by 6 ft. and 8 ft. by 6 ft. respectively), the mill discharges being pumped to a common distributor which feeds seven Hummer Screens. Each screen has three 4-ft. by 2-ft. Ton-cap sections and repulping compartments are provided. The screen oversize is returned to the mills whilst the screen undersize is finished grinding section product. A third (6 ft. by 6 ft.) mill regrinding the coarser table tailings also discharges into the common Hummer Screen Distributor.The screen undersize is pumped to a bowl classifier which separates at 200 mesh. The bowl classifier sands are treated on tables whilst the bowl classifier overflow, after thickening, is treated in the slime plant by flotation. The flotation concentrate is further concentrated on vanners and slime tables.A recovery of 80 per cent. is possible by tabling whereas only 50 per cent can be recovered in the slime section. The object of comminution is, therefore, to reduce all the new feed to less than a certain mesh (22 mesh Tyler) with the production of a minimum quantity of minus 200 mesh material. cheelite is, a very friable heavy mineral (Sp.Gr. 6'0) and is therefore susceptible to overgrinding. For the evaluation of grinding performance it is hence advisable...

Jan 1, 1955

Water is important commodity in the mining industry. Water is used in the many stages of mining from the exploration stages and drilling, to mine development and operation and finally throughout mine rehabilitation and post mine activities. With the use of water throughout the life span of a mine, its management is an important component in the operation of any mine. Unfortunately the use of water within the operations can be one of the major sources of pollution generated from a mine. Such contamination can occur via numerous mechanisms including ground water flow, over land flow and accidents. Contamination may occur in any stage of mining operations, for example a leaking or failed tailings dam. With the above in mind, the paper presented will focus upon the use and management of water in the mining industry: ownership rights of water û common law as well as legislative rights; a review and analysis of the existing Queensland legislation and its mechanisms for the protection of water pollution from mining operations; and conclusions drawn from the paper relating to the Queensland legislation.

Jan 1, 2003

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

The geochemistry of waste rock from mining operations is critical to the development of acidity-related environmental problems during mining operations, and following mine closure. Failure to recognise the potential for waste rock to produce acidic oxidation products may cause mobilisation of heavy metals into ground and surface waters, and create heavy metal levels in soils which are toxic to plants, causing the failure of revegetation programs. Although more usually associated with wet tropical environments, the potential exists for these problems to occur even in and regions such as the Eastern Goldfields region of Western Australia unless appropriate pre-planning is undertaken.Acidity-related mine waste problems can be extremely expensive to rectify, but can be avoided by waste rock characterisation, and pre-planning of waste rock deposition based on this information. Integration of knowledge of waste rock geochemistry with geotechnical engineering, and application to likely problems, is essential for the successful planning and implementation of cost-effective strategies to avoid problems occurring. Pre-planning to avoid problems is likely to be significantly less expensive in most cases than remedial actions to rectify problems after they have occurred, and in fact may involve no additional cost if it requires only rescheduling or redesign of existing or planned Activities.

Jan 1, 1993

By Worner H. K

Education has always been a topic to rouse the interest of mining and metallurgical engineers, but the recent activities of the Education Committee of the Australasian Institute of Mining and Metallurgy 1, 2, together with the moves throughout the Commonwealth to extend the field of technological education, have made the subject a very live one at the present time. The authors have felt it would be appropriate that on the occasion of the First Ordinary Meeting for 1950, in Victoria, some contribution should be forthcoming concerning the history, present status and possible future trends of mining and metallurgical education in this State. As for the past, the time approaches when there will be none having personal recollections of the beginning of Victorian mining schools or of the men who started them. As for the future, it is obvious that rapidly expanding metal-producing and metalconsuming industries will demand a greater output of competent graduates and diplomates. The era immediately ahead seems to be bristling with opportunities, but mining educators need to temper their enthusiasm for various policies and programmes with the realisation that they are helping to train men who will be leaders 15-20 years hence when the problems of industry and trials of life generally may be very different from what they are to-day.

Jan 1, 1950

By B J. Beven, A Vatandoost, J Young, S Campbell-Hardwick

The intrinsic value of iron ore depends on its physical and chemical characteristics. For example, silica and alumina are unwanted elements, downgrading iron grade and adversely affecting high temperature processing, attracting penalties in smelter contracts. For this reason, an informed knowledge of processing characteristics and product quality of the ore is valuable and cost effective during mine planning and processing.Ore variability is a significant factor that affects metallurgical behaviour and efficiency of ore processing equipment. Ore of sufficient chemical and physical quality needs to be modelled, mined, processed and usually blended. Feed and product assays are commonly used to assess potential ore upgradability. However, assays alone cannot be all informative of actual processing response given the variability of the physical properties of the ore.This study investigates the potential benefit of implementing a geometallurgical approach during the commissioning stage of the Kings deposit, part of the Solomon Iron Ore project in Western Australia. Kings drill hole database information, ie geological, textural and geochemical data, together with the results of metallurgical test work were used for geometallurgical analysis and modelling. Three main ore types were identified at Kings, namely channel iron deposit (CID), bedded iron deposits (BID) and Detrital Iron Deposit (DID). Additional classifications were utilised to better characterise these units in terms of their physical properties.Bulk sampling for each ore type was carried out across the deposit for metallurgical testing. Multivariate statistical models were developed for prediction of product quality for each geometallurgical unit. A new approach for modelling yield based on ore upgrade factors is introduced. These models were then applied to the Kings regularised mining model to assess product quality across the mining blocks and to plan product stockpiling and blending strategies.CITATION:Vatandoost, A, Beven, B J, Campbell-Hardwick, S and Young, J, 2013. A geometallurgical approach for iron ore product evaluation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey's success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

By C Kocsis, G Baiden, Y Bissiri

CANMET-MMSL and Penguin Automation Systems Inc have been exploring how process simulation and ventilation modelling software, when combined, can be used to optimise hard-rock/metal mine ventilation systems. In combination, it is anticipated that this methodology will facilitate the exploration of mine design options that affect ventilation requirements and ultimately cost. Such integrated mine design could limit, and possibly reverse, the drivers that under current practices would generally dictate increased ventilation, power consumption, cost and greenhouse gas emissions. It is believed that the mining industry needs such process models to develop better business cases. For example, the implementation of optimised ventilation systems will undoubtedly require significant investment and mines are often reluctant to try such conservational measures unless they can be proven cost-effective. In general, Canadian hard-rock mines know their ventilation systems are providing too much air and consuming power unnecessarily. This is because their systems are designed to provide maximum production flexibility, based upon peak demand, which may be at some future time, and operated continuously at that level regardless of actual need. Simplistic analyses have shown electrical energy savings can range from 30 per cent through to 90 per cent (Hardcastle, Gangal and Leung, 1998). These savings depend upon such factors as the intensity and continuity of the production schedule as opposed to non-productive time. Where these savings occur is also important, if limited to either the primary or auxiliary ventilation systems, they could be negligible in a mineÆs total energy consumption. The problem these mines face is determining what level of ventilation is required in real-time and then the relative benefits. Such parameters as varying electricity costs, heating fuel options, different design criteria and their complex inter-relationship can effect the selection of an optimal system, depending on whether energy, environment or cost is the prime driver. The use of process simulators in underground mining is in its infancy; to date they have been used to show the benefits over the life of a mine under different mining methods, such as a comparison of tele-remote mining from surface against conventional manned operation (Baiden, 2000). This ongoing development advances the use of such simulators into a new and potentially important area, namely modelling the life-cycle ventilation requirements of a mine. This paper shows how such a life-cycle analysis as opposed to peak demand can provide the basis for optimising the design of ventilation systems and their control.

Jan 1, 2005

Close spatial relationships between the deposits of the Etheridge Goldfield (23,000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic. Acceptance of this hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so. Consequently there is little scop- for the discovery of extensions of this field. However, the stratigraphic interval between the source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1980