Search Documents

Vertical retreat open stoping (VROS) is a variation of sublevel open stoping (SLOS) that has been introduced at Cannington to minimise the influence of subvertical geological structures during stope extraction. The first application of VROS is described, where structures within the stope resulted in a change in firing sequence and the extraction of two complete sublevels in a single blast. The use of electronic detonators is critical to the success of VROS and their application is described. Numerous benefits of using VROS have been identified and are described. To date, eight stopes have been successfully mined using VROS. In addition to the first application of VROS, two further case studies are described.

Jan 1, 2005

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

Environmental management of minesites in general, and management of water discharges in particular, is receiving ever-increasing attention. One key component in the successful design and operation of water management systems is to address the presence of sediment in the water being conveyed. Sediment erosion in the mining environment is often greatly exacerbated by disturbing the ground surface of vast areas of catchment. If sediment avoidance, transport, deposition or release are not adequately addressed, the impact on water management facilities can include loss of storage and hydraulic capacity, more frequent equipment replacement, increased operational costs and potentially environmentally unacceptable sediment discharges to receiving waters. An overview of sediment management within water facilities is presented here, and design of one particular approach, the use of settling basins for sediment removal, is discussed in detail. Examples are used to illustrate lessons learnt where particular approaches to sediment management have been found to be lacking. The common themes in the lessons learnt include the need to characterise hydrodynamic conditions and sediment properties in the water source, to set performance targets for sediment management, and to develop operating procedures to meet these targets under a realistic range of scenarios. The examples show how analysis of expected performance of sediment management can help with planning of operation and maintenance strategies. For settling basins, use of a simulation model that includes the effects of turbulence on settling can provide considerable benefits in optimising basin design and evaluating performance. Even in the most basic approach to sediment settling, establishing performance targets based on design flow and sediment characteristics is critical.

Jan 1, 2003

By A S. Lund

Optimisation of the underground mining production process benefits from informed decision making during the process of explosive rock fragmentation. Selection of the most appropriate bulk explosive products for underground production blasting is an area of endeavour that offers significant economic upside if correctly and thoroughly undertaken. The explosive selection process is facilitated by a clear understanding of:the physical and detonic properties of the alternative explosive options available; the response of different rock masses to these different explosive options; and the importance of maintaining a clear focus on desirable blast outcomes in order to enhance value creation aspects of the mining production process. The level of understanding of these issues is raised through the application of measurement and modelling technology, quantifying the effects of blast design (and implementation) on process outcomes. Homestake Darlot and DynoConsult applied a range of dynamic blast measurement and outcome modelling techniques in order to explore the relationship between rock properties, explosive properties and mining process efficiencies. A campaign of vibration and explosive Velocity of Detonation (VoD) measurement produced feed data for use in vibration and fragmentation modelling during the extraction of one of the major stoping blocks at Darlot Gold Mine. The paper describes the use of these tools and discusses the understanding gained concerning the limitations and capabilities of, and the reconciliation between, a selection of analysis and modelling approaches.

Jan 1, 2001

By G R. Mould

The paper presents a general background to the subsidence research program being undertaken by the Department of Mineral Resources and Development in New South Wales. The results of the studies undertaken over the last ten years are summarised. The differences between these results and those obtained by the National Coal Board are discussed. The results of a study carried out on the effect of total extraction beneath a freeway in the southern coalfields are discussed in some detail. The procedures developed for the construction of a 500 mm diameter natural gas pipeline crossing a number of collieries in the northern coalfields are also outlined. The future direction of the Department's subsidence research program is discussed.

Jan 1, 1980

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

By Lynn DR, Wadley GB

The Australian gold industry has made large steps forward in the last few years. This progress has been driven by improvements in mining and processing technology, the high price of gold and by a favourable legislative, political and taxation environment. This paper concentrates on improvements in gold project development, process engineering and technology as seen by BHP Engineering, Perth, Australia.The paper describes technical aspects of successful gold project development including metallurgical testwork, feasibility studies, choice of process flowsheet (gravity, heap leach, carbon in pulp (CIP), carbon in leach (CIL) or other routes). It sets out our views on plant design, plant construction, procurement and project management.A case study for a small plant recently completed in the Philippines is presented as a solution to the problems often encountered in treating quartz vein gold deposits.

Jan 1, 1990

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By O Ostrovski

Iron ore reduction and iron cementation by CH4-H2-Ar gas was investigated in a laboratory isothermal fixed bed reactor. Iron ore was first reduced to metallic iron by hydrogen, then carburised to cementite by methane. Increasing temperature and hydrogen content accelerated the reduction process. Methane had almost no effect on the reduction process. Meanwhile, higher temperatures increased the rate of cementation and also the rate of free carbon deposition. The optimal temperature for cementite formation was found to be 750¦C. At this temperature, reduction of iron ore to cementite by gas containing 55 vol per cent hydrogen, 35 vol per cent methane and 10 vol per cent argon was completed in about 15 minutes. Addition of sulphur into the reducing/carburising gas strongly retarded the process of cementite formation and free carbon deposition. Cementite is an unstable phase which decomposes to iron and carbon. The rate of cementite decomposition increased with temperature up to 600¦C and above 750¦C . In the temperature range from 600¦C to 750¦C the rate of cementite decomposition decreased with temperature. Cementite was the most stable at 750¦C and least stable at 600¦C. The two-interface grain model was used to describe the process of iron ore reduction and the volume reaction model was employed to model the iron cementation process. The simulated results for both reduction and cementation are consistent with the experimental data.

Jan 1, 2000

By J O. Watson, V S. Vutukuri

This paper presents results of an investigation on acoustic emission characteristics of granite, sandstone and rock-like material in the unconfined compression and tensile tests. Both the acoustic emission signature and stress-stain curve are analysed in the experiments.The experimental results show that different acoustic emission characteristics are observed at different stress and deformation stages in unconfined compression and tensile testing. Extensive and unstable acoustic emission changes may be interpreted as indicating failure of the rock.

Jan 1, 1999

By Sakai S, Suga S, Bisque RE

Soil gases were collected on activated charcoal, analyzed by computerized mass spectrometry and treated with multivariate statistical pattern recognition to determine the diagnostic geochemical signature associated with the Okuaizu Geothermal Field in Japan. From this a geothermal model was developed and compare to 175 "unknown" samples in a 250 m spaced grid over 30 1Qn2 mapping the areas with a matching geochemical character. Faults and fractures were generally located by the presence of high molecular weight components. Following the initial survey, the faults in two specific areas were precisely located by a second survey with samples at 10-30m spacing. Where earlier geochemical surveys had placed anomalies 1-2 Km northeast of the geothermal center, the fingerprint survey accurately mapped the system and detected several faulted zones. It was not misled by hot springs located away from the geothermal System.

Jan 1, 1987

By R A. Pax, B Cornish

"Although it is well known and easily experienced that the feed size distribution influences the throughput and stability of operation of a semi-autogenous grinding (SAG) mill, the details are poorly understood since it is often only the input and output measurements that are used to identify unfavourable in-mill conditions. Load cells and power monitoring are sometimes used but are generally poor indicators of the mechanisms that lead to such unwanted conditions.At the MMG Century operation a 12-microphone array around the SAG mill using non-contact acoustic measurement methodology has been used to diagnose the in-mill conditions to facilitate improved throughput and stability of operation. Use of acoustic measurement and control has provided a demonstrated increased throughput of at least 20 per cent as well as improved stabilisation of the mill. Since the information derived from the acoustic noise from a mill allows discrimination of the behaviour of the steel balls and the rock, a number of in-mill conditions can be identified with signals that include toe and shoulder angles, water holdup and the ball to rock ratio.Feed size variations, measured online with an imaging system, have been used to determine their effect on the internal charge behaviour. It has been found that circumferential segregation of steel balls and rock occurs as well as poor mixing of large rocks. Both of these effects are not conducive to optimal breakage rates of different size fractions. Longitudinal segregation effects also occur. This paper presents and discusses these results and illustrates how the new acoustic knowledge can be used to manage and improve mill operation and stability.Citation:Pax, R and Cornish, B, 2016. Understanding Size Effects of Semi-autogenous Grinding (SAG) Mill Operation as a Pathway to Solving Feed Disturbances - Case Study using the MMG Century SAG Mill, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 321–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Fourney W. L, Weaver T. A

A large number of single borehole crater-forming shots were analyzed in terms of correlating the crater parameters with explosive weight. The objective was to determine a scaling rule for which the explosive weights varies over many orders of magnitude and covers many different geologic materials. Included in the data base are type and weight of the explosive, geologic medium and degree of saturation, charge depth-of-burial, crater dimensions, and crater rim (lip) measurements. An alternative scheme to the usual plot of scaled depth-of-burial versus scaled volume removed was desired. The proposed technique uses a plot of the logarithm of the explosive weight, Y, versus the logarithm of the slant length, R', calculated from the known depth-of-burial of the explosive and the measured crater radius. A plot of Log Y in kilotons versus Log R' in meters from all the crater tests in this data base resulted in a straight line with a of slope 0.31 and showed good correlation between the variables Log Y and Log R'. Since the crater data includes many geologic materials, different explosives (including nuclear tests), and large differences in charge weight, the straight line fit suggests that the type and strength of the geologic materials play a subordinate role to explosive energy in crater formation.\

Jan 1, 1990

An exploration and preliminary mine design contract was undertaken in Thailand to establish whether adequate lignite resources existed for the addition of future power generation plant through to the year 2000. The lignite ranges in heat value from 14 to 24 MJ/Kg (air dry basis) and occurs in 2 major seams consistituting measured reserves of 536 Mt (with an ash cut-off level of 45 % on an air dry basis) and a strip ratio of 4.1 bank cm/t. The paper describes the pre-planning, programming, equipment used, project management, logistics and exploration methods adopted to undertake the contract in a monsoonal area using Australian drilling and geophysical contractors.

Jan 1, 1983

By R L. Braithwaite

Mesothermal quartz lodes in Paleozoic Greenland Group metasediments of the Reefton area have produced 67 t of gold up to 1951, and recent exploration has identified new gold resources in several deposits, including the largest past producers, Blackwater and Globe Progress. The metasediments consist of alternating sandstone and argillite, metamorphosed to lower greenschist facies and hydrothermally altered near the quartz lodes. We examined and sampled drill core from four prospects, Globe Progress, General Gordon, Merrijigs and Blackwater, to determine the mineralogical and geochemical characteristics of hydrothermal alteration in the sandstone units. The sandstones are feldspathic litharenites averaging Q65, FlO and R25, with detrital grains of quartz, feldspar, rock fragments, muscovite, biotite (mostly altered to chlorite), and trace quantities of graphite, apatite, zircon, tourmaline and titanite. Hydrothermal alteration has developed a secondary mineral assemblage of K-mica (muscovite, sericite and illite), carbonate, chlorite, pyrite, arsenopyrite and limonite. The abundance of secondary chlorite is greater at Blackwater than at the other locations studied. Features in the sediments associated with increasing hydrothermal alteration towards quartz lodes include, the development and increasing intensity of colour bleaching and carbonate spotting, increasing quantities of disseminated pyrite and arsenopyrite, and the appearance and increasing quantity and size of thin carbonate, quartz and sulphide veins. This is accompanied by increasing concentrations of sulphur, arsenic and antimony as shown in assays, and of volatiles (loss on ignition) and iron as seen in XRF analyses. We were unable to identify consistent trends in the behaviour of potassium, sodium, and calcium that are exhibited by similar mesothermal quartz lode deposits inVictoria, Australia.

Jan 1, 1998

An extensive railway construction prog- ram in the People's Republic of China has required the excavation of many tunnels in difficult ground, particularly in mountainous regions. Conclusions drawn from case histories permit guidelines to be formulated as to the optimum location of tunnel alignments in faulted and folded terrains, and also in karst regions. Geological factors adversely affecting durability of tunnel linings can be minimised by adoption of appropriate construc- tion practices.

Jan 1, 1987

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

The pyroclastic-filled Voorspoed kimberlite pipe has a low grade due to significant internal dilution which translates to a marginal business case. The site, with excavations, tailings dumps and buildings remnant of mining from 1906 to 1912 is to become De BeersÆ benchmark mine in South Africa. In a climate of skills shortages and lean structures, a geological service to optimise exploitation of this complex resource was established. As historical mining removed the higher-grade centre of the pipe, initial production was in the weathered upper benches along brecciated pipe margins. Trenching and blasthole logging before blasts helped to mitigate the effects of the drastic contact deviations that occur when working with an inferred geological model. However, identification of unfamiliar weathered kimberlite and delineation of unmodelled internal waste posed challenges. Efficient grade control by demarcation and allocation of individual truck loads will be vital to continue profitable mining at Voorspoed. Further challenges arose across disciplines. The first yearÆs planned production of mostly weathered kimberlite was processed through a plant designed for VoorspoedÆs unusually competent ore. The high clay content of the weathered material led to clogged chutes and overloaded fines disposal, hampering efforts to commission the plant. Resolving this problem involved mining æout of planÆ to provide a blend of fresh and weathered kimberlite. The calculation of an accurate mine call factor was hindered by a lack of haul truck monitoring, process stoppages and stockpiling in the plant during commissioning. Updating of the geological model to incorporate the contact changes observed in the pit was slowed by the need to first understand how 40 years of exploration data was integrated to create the model. A plan, involving focused mine geology practices, is in place to upgrade a portion of the resource from Inferred to Indicated level of confidence. These challenges are not limited to new mines but will be ongoing as new information is constantly gained at Voorspoed and many mining operations.

Jan 1, 2009

By Coppock BW, Scott TC, Firkin GR

The pollution control measures taken on the Imperial Smelting Process (ISP) operated at Cockle Creek are described together with environmental monitoring strategy and the statutory restraints applied in New South Wales. An outline of developments in the gaseous, liquid and noise control areas is given.

Jan 1, 1975

By W A. van der Westhuizen

Selective mining played a major role in saving a mine and a communityÆs existence as well as creating a working culture that is the model for all KumbaÆs mines. The successes that resulted from selective mining led to receiving KumbaÆs highest award (it was the Gold Medal Breakthrough project of 2003) as well as the productivity award at the National Productivity Institute award ceremony in 2004. Kumba was established in November 2001 (previously Iscor Mining). The new company identified Mineral Resource Management (MRM) as one of its key drivers and an initiative was launched to define MRM in the Kumba way. Best MRM practices at the Kumba mines were included in the definition. Selective mining was born out of this initiative. One of the key principles of good MRM practice was identified as: æThere must be a balance in the operational processÆ. This principle was applied with great success at Thabazimbi Iron Ore mine in the Limpopo province, South Africa. The emphasis of this paper will be to show how value can be unlocked throughout the whole mining value chain. In the past (up to 2001) the mine went through a number of crisis situations: planned production performances were not reached, the stripping ratio was extremely high with two new pits, the product beds were not of constant quality, slope failures were big risks, flooding could and did cut off half of the ore supply, and restructuring demoralised staff.This paper focuses on: selective mining throughput drivers, and selective mining and its role in achieving this balance.The results were dramatic, with huge improvements in production results, stockpiles, plant yields and product bed specifications. The mine was brought into balance and a self feeding loop was created with positive spin-offs up to this day.

Jan 1, 2005