Search Documents

By S Yuen, T Rana, S Khan

Many open pit mines require dewatering or need aquifer depressurisation systems to manage mine water inflow and/or mine floor stability. In many instances these mining operations impact on regional groundwater resources and therefore access to these resources by other users.As such potential exists for mine development to be hindered or even blocked by groundwater legislation that aims to prevent declining groundwater levels and demonstrate equitable use of a regional groundwater resource.There is a need to manage aquifer systems during and after the mining operations, and in some cases stresses on the aquifers and associated ecosystems may be elastic and can be managed with minimum impacts or reversed once the mine ceases to operate.This paper uses the Gippsland sedimentary basin, with a history of declining groundwater levels and mining and petroleum production, as a case study to pose the question: Should period of mining operation, aquiferÆs storage capacity and its ability to recharge be concurrently considered when granting groundwater abstraction and mining licenses for prospective mine development?It further examines that by utilising an aquiferÆs storage capacity and demonstrating an understanding of aquifer system hydrodynamics during and beyond the life of the mine (time), the approval process for groundwater abstraction and associated cost of statutory monitoring may be made less onerous.

Jan 1, 2009

About twelve months ago, owing to the increasing quantity of stone and dirt being drawn frQm the Victorian State Coal Mine due to the large amount of dead work below ground, cutting, faults, etc, and to the increasing quan#ty of banded coal beingworked, the writer was forced to consider the question of economy in handling the spoil at the surface. The method in operation at the time was to run out level dumps fro,m the, tipping floor of the heapstead, or brace, and to tip most of the skips of stone in tipplers at the ends of the dumps, the remainder of the skips being side-tipped to widen the dumps.The method, whilst quite satisfactory for dealing with a few skips of stone, was found to be costly as the dumps extended, and the number of skips to be dealt with increased from 300. to 400 per day of two shifts;. therefore, in order to expedite thework and cheapen its cost, the writer devised an improved method which may be qescribed as follows :-(1) The stone is tipped into a hopper car which holds about 10 skips(2) The hopper car is hauled up an inclined dump by means of an electric winch.(3) The spoil is dumped from the car forwards or to either side, as required.(4) The car is returned to the starting point for a further load.Plate I Fig. 1 gives an idea of the construction of the hopper car. In the illustration the car is in position for tipping to one side. The body of the car is supported on a ball race on the under carriage, and it can be swung round to tip in any required direction. The bottom of the hopper is extended to form a 4 ft. lip...

Jan 1, 1918

By Mayer TE

The Granites Goldfield is located 550 km northwest of Alice Springs. Mineralisation was discovered in 1900 and intermittently worked along nine km of strike until the early 1950's, yielding a recorded production of 470 kg of gold. The geological environ- ment, pre-existing exploration drilling results, and an optimistic view on gold, prompted acquisition of the property by North Flinders Mines Limited in 1975. An agreement was signed with the Central Land Council in August 1983 and drilling commenced in the same month. In the past, gold was won from alluvial deposits, rich quartz veins and lower grade, disseminated stratabound mineralisation. The last is contained within a distinctive unit in the Mt. Charles Beds, of the Early Proterozoic Tanami Complex. This informally named "Host Unit" is a metamorphosed, chemical- pelitic sediment. The schist contains variable proportions of amphibole, quartz, garnet, clinopyroxene, carbonate and sulphide, inter- calated with recrystallised chert beds. Free gold occurs in several mineralised horizons within the Host Unit, generally conformably distributed within lithologic bands or at lithologic contacts. The Host Unit occurs within a sequence of metamorphosed pelitic sediments and intermediate volcanics. Although mostly confined to the Host Unit, stratabound gold mineralisation also exists in both Footwall and Hanging Wall Schists, usually within zones displaying certain Host Unit characteristics. The deposits may be loosely categorised as being of banded iron formation (bif) type, although some important differences are noted between them and classical bif type orebodies.

Jan 1, 1984

Small mines exist because of a restricted deposit or a small market. With the right management at the present time the small mine can have lower total costs than larger mines. Charbon is an example of a small mine with a restricted deposit and a specialised product. The development which incorporates a unique rail loading facility and flexible coal preparation plant was achieved with a modest capital outlay and in record time. To remain competitive in future with large scale mines who seek increased production the small mine must achieve increased productivity through automation, higher speed equipment and a multiskilled workforce. Deregulation of the industry, scrapping the Coal Industry Tribunal and the Joint Coal Board would benefit small mines greatly. Management of a small operation also requires multiskills which need to be supported by outside help in the form of consultants and temporary staff. In the 21st century small mines will continue to provide a service to the market.

Jan 1, 1988

The society in which we live is one of change, and we professionals are part of that society. The importance of this simple and obvious statement is often overlooked. My Presidential Address examines the question: can professionalism survive in our changing society?There is ample evidence to show that our society is changing, and that the rate of change is exponential. This rapid and accelerating rate of change is what Alvin Tomer refers to as "future shock". Rapid change means that we do not have time to become accustomed to what is happening around us and to feel comfortable with it; the greater the rate of change the greater the discomfort. The effect that this has on people is varied; the change may be either expected or totally unexpected.The rate and extent of change in society is not the same for all countries nor for all industries or occupations. Change is more rapid in Japan, Korea or Taiwan, than in Australia. It is more rapid in our cities than in the bush, more rapid for professional businessmen than for farmers. In our minerals and petroleum industries, we are still adjusting to the great changes that have taken place over the last fifteen years. In the past, products from our industries were sold on a free and open market. Today, mineral development and production in most undeveloped countries and some developed countries is manipulated for political, social and economic reasons. Changes of this nature have had a devastating effect on the operations of established mineral producers in the democracies.Because of the accelerating nature of change, we must recognise that the past is not a reliable guide to the future.Although extrapolation of the past into the future is a basic ingredient of commercial survival, extrapolation is less and less reliable.I borrow from others in quoting the Irish proverb: "The future is not what it was".The future is where our business lies and most of us at this Conference must endeavour to understand it and adjust to it. I believe in the old adage that:You can't know where you're going if you don't know where you've been and where you are at.There are a number of major factors which have created change within our social, economic, and industrial environment in recent years.

Jan 1, 1985

The safety in pillar extraction is closely allied to the design features of the pillar extraction system. Considering the conventional supported systems of pillar extraction there are problems associated with complying with the design system outlined. The accident causing agencies and the legislative action to overcome them are im- portant aspects. There is merit in the regularity of support and the limiting of the effects that human error can cause. But new problems and hazards are introduced by this powered support equipment. The comparison of accident experience is difficult due to lack of records and lack of uniformity of approach, but it is clear that powered supports provide a safer system. Every progress in research and practice provides further data to employ in accident prevention.

Jan 1, 1974

By H P÷llmann

Calcium aluminates, calcium aluminate ferrate and calcium aluminate sulfate were synthesised by solid-state reaction, sol-gel method, a self-combustion method and by a polymeric precursor process. For chemical sintering methods the base chemicals CaO, CaSO4, Al2O3 and Fe2O3 were used. As precursors for sol-gel synthesis metal nitrate hydrates and Al2O3-Sol were used. In order to synthesise pure phases by a self-combustion reaction glycine was used as fuel and nitrates as metal components. In the polymeric precursor process metal nitrates and diluted H2SO4 were used as metal components and the resin was made using citric acid (C6H8O7) and ethylene glycol (C2H6O2). Precursor phases synthesised by these different methods were sintered step-by-step in order to investigate the crystallisation. Further on single phases were hydrated and their hydration behaviour was studied by heat flow calorimetry, X-ray diffraction and cryo-transfer scanning electron microscopy. Due to the different synthesis procedures different hydration reactions and microstructures of the phases will be shown.

Jan 1, 2008

By B Lyne

In 1990, the Queensland mining industry had come to the conclusion that new safety and health legislation based on risk identification and control was required if the mining industry was to be effectively and efficiently regulated. In particular stakeholders in the coal mining industry had arrived at this opinion after the industry had suffered a number of major underground explosions over the 14-year period between 1972 and 1986. Also by 1990, a general consensus had emerged across both the coal and metalliferous mining sectors that mining industry was over regulated and, more to the point this over regulation did not encourage industry to identify and address the underlying causes that had led to a cycle of major mining accidents in the state. The prevailing opinion was that the prescriptive legislation left the ownership of risk management with the regulator and not with the mine operator. This paper discusses the background to the development of the Queensland Coal Mining Safety and Health Act 1999 and the Mining and Quarrying Safety and Health Act 1999 and the progress made in improving safety and health since the statutes came into force on the 16 March 2001. The paper discusses the issues that had to be addressed during the development of the legislation including the interaction with other legislation based on based on risk management principles that either overly or interface with the mining legislation. The effect the underground explosion at Moura No 2 in 1994 had on the final content of the new legislation is also considered. Health is often the neglected twin of safety and health legislation and the paper previews the health surveillance system being proposed in Queensland to ensure that health of mine and quarry workers is afforded the same priority as their safety. By increasing the structured management of occupational health problems in our mines there is an opportunity to make significant improvements in mine safety In conclusion the paper reviews the results to date since the introduction of the new mining safety and health legislation in Queensland on the 16 March 2001. Progress has been made and more is yet to be achieved

Jan 1, 2003

By D J. Clark, R F. Wright, M D. Goodz

The A1 Gold Mine is a Devonian-age narrow vein high-grade gold deposit located 115 km east of Melbourne. The mine operated almost continuously from 1861 to 1992 producing 442 334 ounces of gold (13.8 t) from 530 436 tonnes from primary gold ore tonnes processed at an average recovered grade of 25.9 g/t Au. The A1 dyke was attributed with a yield exceeding 620 000 ounces (19.3 t) of gold (including gold in alluvial and tailings deposits), and was renowned as one of VictoriaÆs premier mines paying considerable dividends. The orebody was principally in a diorite dyke bulge 150 m long, 45 m wide and 700 m deep and was mined via two vertical shafts. The mine site was closed in 1992 and the site was rehabilitated in 1999. In 2008 - 2009, a diamond drilling program identified various extensions to the host dyke lithology and to gold-bearing quartz vein filled fault zones over a 700 m strike length. The outcome of this study was the establishment of a mine geology corridor four times longer in strike length than the original 1970s model. This opens A1 dyke hosted deposit style to exploration outside the historical dyke bulge and provides exploration opportunity for all similar deposits. Construction of the first 3D geological model has developed new insights on the host rock diorite dyke system and identified various extensions to both host stratigraphy and to gold-bearing mineralised structures. Coarse visible gold in quartz vein mineralisation (>30 g/t Au) and medium-grade stockwork mineralisation (8 - 15 g/t Au) has been intersected within 100 m of the surface and up to 300 m along strike of the nearest historical underground workings. At depth it appears that the mineralisation is continuous with the main dyke body with consideration of minor rotation in the strike orientation and limited reverse thrust faulting showing maximum displacement of 10 - 20 m. Along the A1 mine corridor, between two and five parallel dykes are observed at different drill sections. The gold mineralisation is hosted mainly within the dyke rocks, but where the sedimentary rocks are intensely silicified or are xenolith rafts, the gold mineralisation continues across these sedimentary rock blocks. There has been inference to the role of silicified sedimentary rocks as a second ore host and a bounding material for inflections in fault and vein orientations. In the central 150 m long A1 mine dyke bulge, the extremities are demarcated by four to five parallel dyke fingers (referred to as apophyses) going both north and south. These apophyses are clearly observed both vertically and horizontally between levels No 4 and No 9. The dyke fingers entrap sedimentary rock xenoliths and collectively form the A1 dyke æcorridorÆ, which is quite uniform in overall width from the easternmost contact (footwall) to the westernmost contact (hanging wall). Dyke fingers were assumed to coalesce at depth into a single dyke, but recent drilling shows this feature to repeat in several positions with depth and along strike. Key observations are the relationship between gold grade and fracture density, alteration, sulfidation, host rock morphology û relation of contact shape and fault zones. These relationships allow for the classification of prospectivity indicators and geology as a guide to potential extensions of mineralised zones. Mining geology is contributing to the whole-of-mine life planning and development where decline path, stockpile and infrastructure positions are controlled by geology.

Jan 1, 2009

By N Taylor, P Hewitt

The Northern Beaches Storage Project (NBSP) is part of Sydney Water’s SewerFix™ Program to improve the wastewater system and protect public health and the environment. It was built by the SewerFix Wet Weather Alliance (the Alliance), a partnership between Sydney Water, RPS, MWH, Parsons Brinckerhoff and United Group Infrastructure.The project temporarily stores excess wastewater diverted from the Narrabeen Submain during wet weather. The project considered a below-ground storage facility, which involved constructing a deep tunnel from Brookvale to Fairlight, connecting into the Northside Storage Tunnel and a storage tank, which was subsequently adopted and constructed.The storage tank scheme included a pumping station and inlet and outlet pipes installed by microtunnelling. The storage tank site is in the Brookvale industrial area situated in an area of deep marine sediments overlying Hawkesbury Sandstone at about 30?m below ground. Microtunnelling for the inlet pipe was conducted from a 12?m deep jacking shaft. The jacking shaft and 14?m deep pumping station excavations were carried out from within secant pile earth retaining structures adjacent to existing buildings.Construction activities had the potential to cause settlement of the adjacent buildings. During excavation and microtunnelling the water ingress, adjacent groundwater level and settlement of the adjacent buildings were monitored. The monitoring data was assessed against an action plan, which modified construction activities as required to minimise the risk of damage to buildings from settlements caused by lowering of the groundwater table outside the excavations. The secant pile construction, excavation, microtunnelling and pumping station construction proceeded without incident or damage to adjacent buildings.This paper highlights that tunnel/underground options should be considered during options development, describes the original storage tunnel scheme and presents details of the successful microtunnelling and deep shaft construction adopted on the NBSP.CITATION:Taylor, N and Hewitt, P, 2014. Tunnelling on Northern Beaches Storage Project, Sydney, to improve water quality, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 451–458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

This paper will address this question from the point of view of a drill and blast engineer or researcher working in open cut and underground mining operations. The paper will establish a common set of reference standards for high-speed imaging and data capture, which engineers and researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of mining and blasting applications analysis and research. In addition, the paper will examine the different technologies from an image quality and data stream reference point, ease of operation, cost, and reliability parameters. Finally, this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of quality control, research and analysis in the mining based industries. This will include a novel approach to digital high-speed imaging and data analysis in the field, which should deliver high-quality images and data analysis in a time frame that is more appropriate to the need for immediate action, analysis and problem solving.

Jan 1, 2007

Congratulations on your considerable enterprise in securing the opportunity to have this international conference here in Brisbane - and congratulations on your success in attracting such a distinguished audience from so many nations, with such a broad selection of papers. It is a notable achievement that in the year in which Australia is celebrating two hundred years since settlers first came fran Britain, The Australasian Institute of Mining and Metallurgy is responsible for some ten major conferences, of which at least four are specifically international, or have a very strong international involvement.

Jan 1, 1988

Christmas Island contains large deposits of phosphate minerals varying from high-grade calcium-phosphate (apatite) to lower grade iron and'aluminium phosphate (crandallite/millisite). The surface material is dominantly C-grade (Fe/Al) phosphate profiling into B-grade, a variable mixture of C- and A-grade ores, before reaching the high A-grade phosphate (apatite) which overlies a limestone Karrenfeld Base formation. A-grade ore is the basic phosphate used for the manufacture of superphosphate and phosphoric acid, whilst B-grade contains amounts of iron and aluminium which are unacceptable for these acidulation processes. Research into methods of separating the finer iron and aluminium phosphates from the coarser calcium phosphates has led to the development of wash-screen processes enabling recovery of 50 to 60%, as A-grade phosphate. Developmental stages included laboratory investigations, mineralogical studies, pilot tests leading the initial 20 tph prototype production unit and the current 100 tph production wash/screen plant, commissioned early in 1970 at Christmas Island.

Jan 1, 1971

By E Widzyk-Capehart, P Vallejos, R Asenjo, J Ruiz-del-Solar

Throughout the minerals industry, it is evident that a new wave of technological innovation is needed as the mining sector looks for ways to achieve higher security and safety as well as higher production rates with less investment. Innovation has always been one of the key factors in achieving success within the mining industry. However, its importance will be especially relevant in the coming years if negative trends in commodity prices and new challenges facing the industry (lower grades, deeper mines and economy of scales) are to be overcome and the future sustainability and profitability of the sector ensured.The drive towards fully autonomous operations has begun, with the implementation of automated systems in both surface and underground operations. However, these automated systems are currently planned and realised with well-defined automated tasks within structured environments and isolated spaces. Currently, there is no interaction between automated systems, manned systems or humans, which creates physically isolated environments.For fully autonomous and continuous operations, the automated systems need to operate in environments that enable flexible interactions between automated machines, tele- and manually operated machines and humans.In this paper, we address the automation paradigm considering the synergistic collaboration between humans and automated systems. In this paradigm, humans and machines would interact in a flexible, collaborative and synergistic way without the need for isolation. The implementation of this concept within mining operations will have to be underpinned by science and technological developments and will require adaptation from many fields, including robotics, automation, distributed systems, communication, human factors, pattern recognition and mine design.The paper also presents the research and development work being undertaken at the University of Chile’s Advanced Mining Technology Center, in collaboration with the Chilean mining industry. This will provide the basis for flexible interactions between humans and technology-based systems towards a future of autonomous and continuous mining systems.CITATION:Ruiz-del-Solar, J, Widzyk-Capehart, E, Vallejos, P and Asenjo, R, 2015. Synergistic collaboration of humans and automated systems – innovative steps towards fully autonomous and continuous mining systems, in Proceedings Third International Future Mining Conference, pp 83–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Giannini L. M

Optimisation techniques, based on the block model, for solving the optimum pit limit problem were discussed in an earlier paper. Of the available techniques the one based on graph theory proved to be the most attractive. In the graph theory model the vertices represent blocks and the arcs represent the mining restrictions. For large ore-bodies direct application of the graph theory method poses considerable computational and storage problems. Techniques for easing the computational effort by reducingthe problem size were introduced in an earlier paper. Further, significant computational savings can be made by exploiting the structure of the graph. This is done by building the graph up level by level and successively applying the graph theory algorithm to reduce the number of blocks. In building up the graph in this way one needs what is called a "search pattern" to indicate which arcs are to be added as new vertices are introduced. Moreover, as it is essential to keep the number of arcs to a minimum it is necessary to establish a "minimum search pattern".The problem of determining minimum search patterns for any block model and for any wall slope restrictions has not been considered in the literature.The objective of this paper is to present a complete solution to this problem and to discuss, through typical case studies, the application of the associated software developed.

Jan 1, 1988

By M Battersby, F Parra, S Sanchez-Pino

Pneumatic flotation, as developed by Dr Rainer Imhof, has been applied in commercial beneficiation operations since 1987. Over 85 flotation cells have been installed in more than 30 operations, successfully beneficiating a wide range of minerals. Pneumatic flotation is however still considered as a non-conventional flotation process. Due to its highly selective nature in operation it has generally found its market in difficult applications where conventional flotation equipment has struggled. Compa±fa Minera Huasco (CMH) operates an iron ore pellet plant in central Chile. CMH desired to produce a low silica pellet for the export market where the SiO2 grade should not exceed 1.5 per cent. It is common practice in other countries to float quartz from hematite with relative ease. However, the silicates contained in the magnetite ore of CMH are only present as quartz in small quantities and the major undesirable silicates are difficult to float. CMH spent considerable time on developing a reverse flotation process and a reagent suite to try and reduce the silica content to acceptable levels. However, extensive laboratory and pilot plant tests with conventional mechanical tank type cells and with column cells failed to produce the required reduction in impurities. A series of tests with pneumatic flotation cells indicated that this type of flotation technology could achieve the required silica target. A 500 tph Imhoflot pneumatic flotation plant was subsequently constructed and successfully commissioned by CMH, making it one of the largest iron ore flotation plants in the world. This paper details the background and testing that was undertaken by CMH which led them to choose pneumatic flotation as the preferred process and compares the test results with that achieved in the industrial plant.

Jan 1, 2005

By T Mattiske

The Fimiston Open Pit (commonly referred to as the æSuper PitÆ) is a part of the Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) operation in Kalgoorlie-Boulder. KCGM manages the Fimiston Open Pit, the Mt Charlotte underground mine, the Fimiston Mill and the Gidji Roaster for its Joint Venture Owners, Newmont and Barrick Australia. KCGM produces up to 850 000 ounces of gold per year. The KCGM operations are located on the historical Golden Mile on the outskirts of the City of Kalgoorlie-Boulder, about 600 kilometres east of Perth Western Australia. This traditionally underground mining centre has been worked since 1893, yielding in excess of 50 Moz of gold from ore with an average head grade of 10 g/t. This represents approximately ten per cent of the gold produced in Australia and one per cent of the gold produced in the world. The Fimiston Open Pit is essentially an aggregation of what were known as the Judd, South, Paringa, Croesus/Eclipse, Central, Brownhill, Drysdale, Morrison, North and Horseshoe pits into one continuous large-scale operation. The old Fimiston Underground Operations (included the Main, Croesus, Chaffers, Lake View, and Perseverance shafts) were also located within the area of the Fimiston Open Pit. The underground operations closed in 1992 due to high mining costs.

Jan 1, 2002

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005