Search Documents

By I Özen, G Chitumbura

A paper identifying anticipated challenges in the extraction of the N3500 Orebody at Glencore Xstrata Copper’s Mount Isa Copper Operations was written in 2007. The paper identified the depth of the deposit, the anticipated high stresses, talc alteration and issues with ground support as factors that may affect production. A number of strategies were planned to cope with these issues. After six years of extraction those strategies are evaluated and additional measures taken are outlined. Strategies to cope with the limited mine life are presented, and methods to overcome additional challenges encountered during production are described.CITATION:Chitumbura, G, Matthews, D, Özen, I and Jackson, S, 2014. One mile underground – mining the N3500 orebody at Mount Isa Mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 265–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

By S Long, A J Koen, D MacKay

The Mt Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. Following the evolution of the mine plan through a number of stages, the ‘sublevel shrinkage (SLS) with continuous fill’ mining method was implemented in 2010 to extract the Mt Wright orebody. The production front in this mining method is similar to a sublevel cave (SLC) operation; however, backfill is placed into the top of the production zone as opposed to requiring the overlying strata to cave.Continuous fill to replace the void created by extracting the ore was required to manage the potential risks associated with the proximity of infrastructure to the footwall, associated long-term stability and air blast potential due to the limited ‘cavability’ of the material within the cave zone. The available fill material was sourced from a disused waste dump from a previous open pit operation, which introduced further technical and economic risks associated with dilution from ‘no grade’ broken material. Procedures and processes to manage these risks have been incorporated into the operation of the mine.Despite encountering a number of challenges, the SLS method has been in use for approximately three years at Mt Wright and has proven to be viable economically, technically and operationally. This paper will discuss the challenges encountered and what was done to overcome them, the operational and financial performance to date, along with the outcomes of some successful continuous improvement projects that have improved the efficiency of the operation.CITATION:Mackay, D, Long, S and Koen, A J, 2014. Sublevel shrinkage – the Mt Wright story, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 205–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Ketelaar P. B, Nichols S, Power W. L, Utley D. C

The impact computers are having in geoscience is distinctly mixed. In the petroleum industry where much of the data are based on geophysics, computers have become an integral part of exploration and reservoir evaluation and simulation. In the minerals industry, the trend to computerisation is more advanced in some disciplines than others. Geophysical and remote sensing data are routinely processed and imaged using state of the art computer techniques. Mine surveying, planning, design and resource and ore reserve estimation are now all predominantly reliant on computers. However senior management of many companies, particularly in the mineral exploration industry, are still reticent to fully embrace the technology. 3D computer modelling of geology and orebody delineation is still largely in its infancy. Two current and significant drawbacks to the routine use of computer modelling of geology in both mining and exploration are the tedious and time consuming modelling process and the lack of seamless interaction between 3D computer-aided drafting (CAD) software and geographical information systems (GIS) which are largely 2D in their data treatment. There is an urgent need for a 3D spatial information system (eg 3D GIS) with intelligent and rapid modelling functionality. One of the keys to the successful building of 3D geological computer models begins with data base structure and design to ensure that there is no loss of data fidelity through data capture, storage, manipulation and modelling. Once a model is constructed, the latest generations of visualisation software provide sophisticated environments over a range of hardware platforms for visualisation in both mono and stereo viewing. This is demonstrated by the geological models which are presented in the digital interactive version of this talk whose URL on the World Wide Web is: http://www.ned.dem.csiro.au/FRACTAL/pubs/talk97AUSIMM/

Jan 1, 1997

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

By Wasp E. J

A review is given of recent commercial long distance slurry pipeline systems in- stalled worldwide. The technological advan- ces in slurry engineering and system opera- tion are discussed, together with a brief re- view of the economics of slurry transportation and future trends in the industry.

Jan 1, 1973

Five types of mineral resource were known in the sedimentary cover of the oceans and seas floors prior to the 1980's :1) hydrocarbon fields including some very large zones of oil and gas accumulation; 2) "Red Sea" type thermal oozes with increased concentrations of noble metals; 3) ferromanganese nodules; 4) concentrations of metallic sulphides ("Black Smokers"); and 5) cobalt-bearing ferromanganese crusts on the summits and slopes of seamounts. Since then, the so called "White Smokers", containing sulphides of copper and zinc, have been discovered. The ore horizons (manganese, copper, nickel and other metals) of the sedimentary cover of deep-sea basins comprise a sixth type of mineral resource in the oceans. These horizons have not only a theoretical, but also a principal economic significance

Jan 1, 1995

The Ministry of Economic Development has as its slogan æTogether making the differenceÆ. The Ministry is required to work in partnership with the private sector, local authorities, Maori economic entities, trade unions and community groups to transform New Zealand's industrial and economic base. The Government is seeking to achieve sustainable and balanced economic development by: being more actively involved in economic management; working in partnership with the public and private sector and with worker and business interests; focusing on adding value in industries (including primary industries) with long term potential; and bringing the tools of economic policy together in a coordinated way. The Ministry, particularly through its operating group Crown Minerals, is committed to working with industry to achieve mutual goals and to obtain continuing investment in minerals and coal exploration and mining and an active New Zealand minerals industry.

Jan 1, 2000

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

By I Halikia, T Lilis

Lead smelter slags, produced during the last century in quantities ofmillions of tonnes at Lavrion, Greece, have recently been used in theconstruction of Lavrion harbour. In order to evaluate the geochemicalstability of slags and assess their environmental impact on the aquatic environment, a detailed study on lead leachability under conditions that simulate subsea environments was carried out. Leaching experiments using magnesium chloride solutions under mild temperature conditions were conducted and the effect of main parameters on lead solubility was examined. Furthermore, kinetic analysis on the experimental results was performed. Based on the results, lead dissolution increases by increasing the reaction time, magnesium chloride concentration in the bulk solution and temperature, whereas it decreases by increasing the slags particle size. The reaction order was found to be approximately 0.5 at the initial extraction stages and the activation energy value from the Arrhenius plot was estimated to 29.8 KJ/mole. Diagnostic equations applied to all the experimental data reveal that lead dissolution is mainly controlled by diffusion through the ferrosilicate matrix of the slag particles, which is in accordance with the low activation energy value. The JanderÆs diffusion equation [1-(1-a)1/3]2=kt was proposed as the equation representing the reaction of lead dissolution from slags using magnesium chloride solutions.

Jan 1, 1999

By R G. Skirrow, M Cooper, J Claoué-Long, K Czarnota, H Dulfer, J Thorne, D C. Champion

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Tholeiitic intrusion-hosted nickel (PGE-Cu) sulfide deposits are under-represented in Australia’s inventory of known resources of this deposit type, relative to regions globally with comparable geology. To support discovery of major new deposits, a continental scale analysis of Australia’s potential for tholeiitic intrusion-hosted nickel (PGE-Cu) sulfide deposits is being undertaken. The analysis applies a mineral systems approach to map the four essential components of the ore-forming systems:1. sources of ore constituents2. crustal and mantle lithospheric architecture3. energy sources or drivers of the ore-forming systems4. gradients in ore depositional physico-chemical parameters.The results reveal several regions of Australia with potential for discovery of large tholeiitic intrusion-hosted nickel (PGE-Cu) sulfide deposits, mostly around the margins of Archean and Proterozoic lithospheric blocks. These include the south-east and northern margins of the Yilgarn Craton, the south-west and south-east margins of the Kimberley Block, the southern margin of the Arunta Province in central Australia, the western flank of the Gawler Craton in South Australia, and possibly some areas within the Palaeozoic Lachlan Orogen of eastern Australia.CITATION:Skirrow, R G, Dulfer, H, Czarnota, K, Champion, D C, Thorne, J, Cooper, M and Claoué-Long, J, 2015. Australia’s potential for nickel sulfide ore systems – a new continental-scale time-space framework for exploration, in Proceedings PACRIM 2015 Congress, pp 679–684 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Today's emphasis on the enterprise bargaining process must be seen as an opportunity for organisations to further develop occupational health and safety standards at work. In particular, this shift from a centralised industrial relations system to employer, employee bargaining, presents organisations with an excellent opportunity to develop OH & S at the `shop floor' level. This is despite real difficulties in presenting hard data on the cost benefits. Unfortunately, examination of enterprise agreements ratified by the Australian Industrial Relations Commission (AIRC), show that less than 32 per cent contain provision for occupational health and safety. Those addressing the issues of occupational health and safety have included segments such as: ò rehabilitation activities; ò a new emphasis for workplace occupational health and safety committees; ò formalising procedures related to hazard identification and control; ò the use of personal protective clothing; and ò occupational hygiene and health monitoring issues. For example, an enterprise agreement reached between CIG-Gases and their unions, included clauses which commit employees to attending ten safety meetings and two work place inspections each year, in order for them to receive any further pay rises.

Jan 1, 1995

This paper has been developed for æThe Race for SpaceÆ conference. It ranges over various aspects, all of which are within the umbrella of marketing. The question is posed because many engineers, tunnelling and other specialisations, frequently demonstrate an unwillingness to embrace marketing. The accurate reply is probably à ænot an engineer!Æ The paper identifies some of the possible explanations for this reply. The vast majority of the themes, ideas and principles are based on more than 25 years actual experience for the author with Engineers, Tunnelling and other disciplines. This experience has been gained with leading consulting engineering practices; some of the worldÆs largest construction contractors together with other organisations employing engineers in the public, private and tertiary sectors in the UK; US; Europe; the Middle East and throughout Australia and New Zealand. Experience has been gained in design offices; head offices and construction job sites in four contrasting continents. The most significant themes developed throughout this paper are as follows:æLetÆs go and do some ærealÆ work and leave the marketing to others!ÆæMarketing is just a æsoftÆ option and neither technically based nor true management!ÆNIMBY-ism (Not In My Back Yard) so leave well alone!Engineers regularly confuse services marketing -v- product marketing à a useful cop out, or a genuine cry for help?Marketing databasesæLetÆs get rid of the term æsellingÆ and replace it with the more acceptable à and less distracting for tunnelling engineers à 'marketingÆDistinction between benefits and features à in The Race for SpaceSales Comprehension Test, Benchmarking TestJack WelshÆs æmost difficult decision for a CEOÆHarvard Business ReviewÆs (HBRÆs) formula for performanceMany engineers are losing the balance in their lives Sustainable development and engineering æQuality work doesnÆt mean quality serviceÆMajor recommendationsRecommended references

Jan 1, 1999

Trade unions are people. As organisations they exist to represent the needs and interests of their members; that is the workforce. Thus one of the underlying objectives of the trade union movement has been and will continue to be: achieving from management recog- nition that the labour input to the production process - whether that be in the factory, office or service context - is made up of individual people who can not be treated as just another factor of production. The essential difference between labour input and other factors of production such as capital and raw material is the "humanness" of the individual entities which make up a firm, company or industry's labour supply. Recognition of the "people" input to the production process has essentially two aspects: humanisation of the workplace and the treatment of labour as human beings who have a role to play both within the workplace and within broader society.

Jan 1, 1982

By J Harmse

This paper deals with the modernisation of the brakes on an electrically coupled Blair multi-rope hoist and covers the removal of the old calliper brakes and hydraulic control system, and its replacement with brake discs, disc braking units and hydraulic control systems. The paper covers the braking requirements of the hoist, which is made up of two electrically coupled single-drum hoists, together with the theory behind the choice of brakes and control systems supplied. The paper also covers the project logistics that were required in order to install and commission the new brakes and control systems with the minimum disruption to production on the only rock hoist on a major production shaft. Items covered include the modifications to civil works, pre-installation of bearing lubrication systems, brake discs and hydraulics and the interfacing of the new hydraulic control system to the existing electric control system. It had to be designed to be compatible to a new electric drive and control system due for installation at the end of 2005.

Jan 1, 2005

By Callaghan R. P

Underground production from the low grade copper orebodies at Mount Lyell in recent years has involved surface subsidence of open cut areas. Relevant structural and lithological features of the geological environment are des- cribed. The highly mechanised underground mining system involves sublevel caving and sub- level open stoping with associated hangingwall cave. Monitoring of subsidence and caving has been made by regular visual inspection and measurement of crack development, and by sur- face profile surveys. These simple techniques have proved adequate in assuring management that ground movement is proceeding normally and safely.

Jan 1, 1980

The history of potential large scale development at Stawell in northwestern Victoria dates back to 1914, when Great Boulder Mines Limited, of Kalgoorlie, Western Australia, took up options on some of the major mines in the Stawell Goldfield. Despite this and other attempts by various groups over the next thirty years, mining activity on the field gradually dwindled to the retreatment of old mill tailings.A static price for gold and indifferent drilling results prevented a major effort towards reopening the field until the late 1970's. A renewed exploration effort led to the discovery of sufficient reserves to justify installation of a carbon-in-leach gold treatment plant.

Jan 1, 1984

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Scott A

This paper summarises some of the results of the ACARP-JKMRC project 'Optimisation of Dozer Operations in Open Cut Mines'. The work has involved an industry review, design and conduct of field trials of coal seam preparation using dozers, nume

Jan 1, 1998

By R Lovel, P Fung, J Manuel, M OÆCo

The iron blast furnace is the most widely used and efficient producer of liquid iron. The integrated steel works is however under environmental pressure largely due to emissions from sintering and coking. The combustion of coke breeze during sintering contributes to greenhouse gases (eg carbon dioxide) and is the source of much of the emissions of SOx and NOx. Coke breeze, the fines produced during coking of coal, is also suffering supply issues as coke demand increases while coking capacity is constrained by environmental concerns.CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide can be sequestered into growing biomass prior to combustion. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource. Samples of pine wood flour, sawdust and red gum wood char were characterised and used in small-scale granulation and sintering tests. Red gum char granulated as well as coke and could be used to make acceptable sinter. Large-scale sinter pot test were conducted with char to produce sufficient sinter for ISO quality tests and calculate sintering performance parameters. Results showed that coke could be completely substituted by red gum char during sintering without loss of quality and with actual improvements in sintering performance. Furthermore, gas analyses made during sintering showed that there were significant reductions in SOx and NOx when char was substituted for coke. It is anticipated that the results reported here, although preliminary, will stimulate an increased effort into further research on the use of char in iron ore sintering.

Jan 1, 2004