Search Documents

By Irving H. Wentworth

The little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map, Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90" in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. History. On the discovery of the silver-lead bearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of about 3 miles east and 5 miles west of the town. At the western extremity and near the Car-rolefia mine, a small town called San Pedro was huilt. The

Jan 1, 1913

By John Jermain Porter

In taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Efficiencj-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-recorcis, due to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost-sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences. Efficiency-records supply this need. They compare actual

Jan 1, 1913

By Edward Keller

In a paper, entitled A Uniform Method for the Assay of 'Copper Material for Gold and Silver,' A. R. Ledoux invited the assayers of this country to contribute to a symposium, in which the results of their assays of given samples of copper-matte and metallic copper would be made comparable. This symposiun 2 appeared about one year thereafter; and through it and its discussion, first became generally known the fact that the gold-yield by the all-fire method of assaying is usually higher than by the so-called combination (wet and dry) method, in which nitric acid is employed as a solvent for the copper. In the publication alluded to, the supposed cause of gold-losses in the latter method was declared to be the solvent action of copper nitrate, or of the reduction-products of the nitric acid, upon the gold. Up to a very recent date, gold has been held to be insoluble in pure nitric acid. (The solvent action of any chlorine present in the nitric acid must here properly be disregarded as belonging in the realm of carelessness.) Among later allusions to this topic, W. R. Van Liew3 ascribes the solution of the gold in the combination-assay entirely to the action of nitrous acid at the high reaction-temperature of copper and nitric acid; F. B. Flinn4 believes the low result in gold to be due exclusively to mechanical losses—finely-divided gold penetrating through the filter-paper—but presents no experimental data confirmative of this belief; and 0. Pufah]5 attributes the solubility of' the gold in some coppers to the presence of selenium—a view which appears to be shared by many as-

Jan 1, 1913

By George F. Becker

Complexity of Rock-Fractures. - The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible node of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is, how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints. - It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings, often called joints. These partings are frequently flat surfaces, even when seen in very large exposures, but are sometimes surfaces of moderate single or double curvature. Joints usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in I hand-specimens as mere slaty cleavage consists, in reality, of innumerable microscopic faults. For this reason, Mr. Daubrée rejects the term "joint," as failing to imply the existence of relative motion, and has introduced the terms “diaclase” and “paraclase” as substitutes.1

Jan 1, 1913

Jan 1, 1913

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By E. P. Mathewson

The early development of the reverberatory furnace for smelting copper-ores was the work of the Welsh smelters, particularly those of Swansea. The first record of a reverberatory furnace is made by Jars, who states that in 1755 copper-smelting was effected .in reverberatory furnaces at Middleton-Tyas, in Yorkshire, England. The first patent, of any importance, for improvements in reverberatory furnaces was granted to Thomas Williams in 1778 for the granulation of the regulus. The next was that of William Evetts, in Sheffield, in 1812, for the cooling of the fire-bridge by the admission of air. Charge-hoppers above the furnaces were in common use in 1848. The size of the hearth of the furnaces about the beginning of the 19th century was commonly 11 by 8 feet. No material development was made until the Welsh process mas brought to Colorado, where Richard Pearce, as manager of the Argo works, near Denver, developed the furnace to meet the requirements of a custom plant, under keen competition with lead-silver smelting-plants, using blast-furnaces. His improvements are outlined in Fig. 1, elaborated by permission from E. D. Peters's excellent work,' to which the reader is referred for further details. This figure shows that the furiiaces were in 1878, 9 ft. 8 in. by 15 ft. in hearth; and in 1894, 16 by 35 ft., while the capacity of the furnace had been increased from 12 tons per 24 hr. to 50 tons in the same period.

Jan 1, 1913

Francis Drake, Bulawayo, Rhodesia, So. Africa (communication to the Secretary *):—I should like to place on record some data in addition to those given by Mr. Canby in his paper. I regret that my notes have been destroyed so that I can give no accurate measurements of the water jacket that I am about to describe. This furnace mas erected in Cerro Gordo, Inyo county, Cal., early in 1875, and I think it quite possible that it was the first applied in lead smelting. It was made of plate iron and elliptic in shape, the inner dimensions being about 54 by 42 in. by 48 in. high. The distance between the inner and outer plates was about 6 in. Tuyere holes, one at the back and two on each side, about 12 in. in diameter, were made in this, and in these were placed cast-iron water tuyeres about 16 in. long, the diameter of the blast orifice at the point being about 3 in. The height from tuyeres to feed door was about 9 ft., but the top of the charge was kept about 5 ft. above the tuyeres. There was a space of about 12 in. between the jacket and the top brick-work. This brick-work was supported by a cast-iron plate resting on four cast-iron columns. At the beginning, the jacket was lined with air-dried radial bricks, made of crushed quartz and fire-clay, as it was thought that the jacket would not stand the heat on its bare plates. After a short time the practice was altered and no lining mas put in. The jacket was closed at the top and had a steam drum connected by two pipes at the back. This steam drum was connected to the boiler in which the steam was made for driving the Baker blower, the rock breaker and the pumps. The bottom of the jacket mas also connected to the boiler. The jacket was run under boiler pressure (80 Ib.) for some time, but eventually cracks developed in the inner plate between the tuyere holes,

Jan 1, 1913

By Utley Wedge

In general, the art of securing copper from sulphide ores or concentrates may be said to consist of: (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a prelimiuary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a hydroxide or other insoluble precipitate and reduced to metallic copper by subsequent melting in a reducing atmosphere.

Jan 1, 1913

"Located in Madison River Canyon, about 14 miles by road from Norris, Mont. Built in 1907 by Madison River Power Co.DAM: Rock filled wooden crib structure, 183 ft. long, 34 ft. high or 44 ft. to top of flashboards.SPILLWAY: 140 ft. long, equipped with flashboards 10 ft. high.PIPE: One 10-foot and one 12-foot wood-stave pipe, 7,515 feet long.PRESSURE: One pressure chamber, 32 ft. high, 30 ft. wide and 81 ft.CHAMBER: long, built of concrete.PENSTOCKS: 4 9-foot steel penstocks about 200 ft. long, one for each wheel.WATER WHEELS: 4 double horizontal, center discharge, Sampson special 44-inch turbines, 3,600 h-p., at 100 ft. head. Speed 300 r. p. m„ direct connected to generators.GENERATORS: 4 G. E., W. C., 2,250 k-w., 4,000 volts, 300 r. p. m., 3 phase, 60 cycles, alternators, with exciters mounted on same shaft.TRANSFORMERS: 12 G. E., W. C., 900 k-w., 60 cycles. High tension voltage 23,100, 34,650, 46,200; low tension voltage 4,000, 3,800, 3,600. Now operating at 46,200, delta connected. They can be connected Y for 40,000, 60,000 or 80,000.OPERATION: This is the principal plant of the whole system and carries most of the load."

Jan 1, 1913

By L. W. Bahney

The photograph, Fig. 1, shows the apparatus a little less than half size, consisting of a filtering-flask fitted with rubber stopper through which passes a bent glass tube, and an extraction-thimble fitted with rubber stopper through which passes a glass tube of 0.25-inch bore. Both tubes are connected by a short piece of rubber tubing. A section of a thimble is shown in the photograph ; the tube extends to within & in. of the tapered end. The object of using the thimble is to remove the acid from the beaker after all the copper has been precipitated. Time is saved, the copper is not exposed to the acid alone, and there are none of the losses attending ordinary filtration. I have accomplished these results by means of a piece of perforated platinum fastened in the end of a (0.25-in. bore glass tube and a filter-mat of asbestos, but after my supply of proper length fiber became exhausted I could not replenish it even after purchasing 14 lots from four different dealers. The above apparatus may be used to remove at least seven-eighths of a supernatant liquid from a settled precipitate without disturbing the latter. The application of the thimble is best shown by partly outlining the assay for copper, as follows: Dilute the acid solution of copper and other sulphates to 150 cc. in a 200-cc. Jena beaker, place on a hot plate, add 2 drops of concentrated HCl, then place a strip of aluminum in the beaker (this may be bent or straight, as desired). Connect the apparatus, as shown in Pig. 1, with a filter-pump having a strong suction. When the copper is precipitated, remove the beaker from the hot plate and insert the extraction-thimble alongside the strip of aluminum. The acid solution will be drawn through the porous tube. Wash the upper end of the aluminum strip with a jet of hot water, wash down the sides of

Jan 1, 1913

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By N. V. Hansell

The preparation of low-grade iron-ores by concentration, whether or not followed by an agglomeration of the concentrate, has in the United States only recently been recognized as a metallurgical process of vast economical importance for its iron indust.ry. This importance of the process lies not only in the fact that it makes possible the use of ores heretofore discarded on account of their low iron-content or their too high percentage of elements deleterious in the iron industry, but also in its produetion of a raw material for the blast-furnace that is more uniform in its physical character and chemically purer, with a higher iron-content, than the general run of natural ores. When mixed in the burden of the furnace, it lowers the amount of coke and fluxing-stone required per ton of pig-iron produced. The furnace-operations become more regular and more easily controlled. The pig-iron is of higher quality and more uniform in character. In brief, it is becoming recognized that the beneficiating of the natural iron-ore, even if it makes the furnace-ore higher in cost per unit of iron entering into the burden, may mean a lowering of the production-cost of the pig-iron and an improved product. At the present time, the Lake Superior district furnishes about 80 per cent. of all the iron-ore yearly produced in the United States. If the Southern States arc exempted the percentage runs as high as 93 per cent. These ores are showing a steady decrease in grade from year to year. For the past 10 or 15 years this falling off in the average grade has been about 0.5 per cent. a year. The lowered grade of ore means an in-

Jan 1, 1913

By R. Moldenke

Unlike the furnaces employed in the reduction of ores to mattes and metals, the foundry-cupola has only melting to do. This looks simple enough; and its development has progressed through centuries by cut-and-try methods; but there is still much to be learned concerning the causes which underlie the production of defective castings, even from first-rate materials. There are other differences between the smelter and the cupola. The former is usually, the latter rarely, run continuously. In the smelter there is some chance for experiment, since rich slags can be treated again; while in the cupola the metal must be good for casting from the first tap to the drop of the bottom ; otherwise, heavy damage will result. In the smelter, the object sought is the production of metal or matte with a minimum loss in the slag; whereas, in the foundry, a variety of castings of different compositions must often be run from the same heat, one after the other. Experience with the cupola has shown that the melting should take place, throughout the heat, in one zone, the zone of maximum temperature, which is clearly marked on the cupola-lining by the severe cutting action of the slag and iron oxide. The design and operation of the cupola must conform to this condition. This conformity having been secured, other considerations resolve themselves into those details of construction which will involve least trouble and cost of repairs. The very high temperatures required to melt iron and steel in the cupola, leaving the metal sufficiently superheated for casting, render the use of water-jackets inadvisable. It is always possible to patch up the lining at the melting-zone between daily heats; and the rest of the lining is seldom affected enough by abrasion and chemical action to require replacement oftener than once in nine months. The cupola is practically a shell of steel, lined with the proper refractory material, and provided with a sct of tuyeres for the admission of air to burn the fuel and melt the metallic

Jan 1, 1913

By Carleton Ellis

The problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific standpoint, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London ; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by may of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of

Jan 1, 1913

W. L. Saunders, New York, N. Y. (communication to the Secretary*):—The Laramie tunnel, though a small one, compares very favorably in the speed of driving with the great Alpine tunnels which have the record so far. I think it safe to say that, taking all things into consideration, the record made at Laramie is the best American record, though it still falls short of the long-tunnel records abroad. In discussing tunnel-records it must always be borne in mind that there are conditions peculiar to each individual tunnel job, so that no comparisons are complete, fair and conclusive. At Laramie there is one point which stands out prominently, and which distinguishes this from any of the recently-built Alpine tunnels, and that is that here we have great progress in an American driven tunnel without the use of a carriage for mounting the drills. At the Arlberg and Loetschberg tunnels, the carriage was an essential condition for progress. All the heading-drills were mounted upon a bar which rested upon a small carriage. This carriage was withdrawn after the drilling and run into the heading after the blast without much disturbance of the drills, and with very little adjustment except that required in jacking the horizontal bar across the tunnel. The carriage was so small in its track-area that it required little mucking to run it in to the face; and as the rock-drills used were heavy machines 38 in. in diameter, progress in setting up and drilling was very much accelerated by the use of the carriage. At the Laramie tunnel hammer-drills were used instead of piston-drills, and here we have an important distinction which

Jan 1, 1913

By H. E. Kramm

During the summer of 1910, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S., and alternating with deep, narrow canyons. The drainage is partly into the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry

Jan 1, 1913

By Frederic P. Dewey

By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called, platinum. Sometimes it is SO, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes gives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid,' I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Jan 1, 1913

Jan 1, 1913

Joseph E. Thropp, Jr., Indiana Harbor, Ind.:—To what do you attribute the fact that in some localities the by-product coke sells at a premium over the ordinary bee-hive coke for foundry use ? If the cell-structure is preferably soft and rather thick in coke for foundry use, as I understand it, do you mean that by-product coke has soft and thick cell-walls ? William H. Blauvelt, Syracuse, N. Y.:—As I say in one of the paragraphs of my paper, the tendency seems to be towards the manufacture of foundry- and furnace-coke under somewhat different conditions. The development of the best cell-structure in coke, of course, has not reached perfection, but we are making progress, and we are inclined to believe that under ordinary conditions the best furnace-coke, that is, coke with the hard cell-wall and the well-developed cell, is produced at fast coking-time and high heats, whereas the best foundry-coke seems to be produced at somewhat lower heats. In one of our plants we are making furnace-coke in 16-hr. coking-time, and foundry-coke in 20-hr. time. Foundry-men want the strong, tough coke. I think the furnace-men present will agree that the best furnace-practice requires a hard coke, with a well-developed cell-structure. Replying to the question as to the reason for higher prices being realized for by-product foundry-coke than for bee-hive coke, of course, the immediate reason is that it suits the foundry-men better. Perhaps one cause may be that we are able, by the selection of coals, which is not usually practicable at bee-hive plants, to get a quality and analysis best suited to foundry-work, with high carbon-content, and with cell-structure and physical strength especially suited to the foundry-men's ideas.

Jan 1, 1913