Search Documents

By P. Barnes

These furnaces are of the ordinary Siemens type, and present no special peculiarities of construction. The bed of each is 8 feet by 20 feet clear inside of the walls and ports. The producers are placed at a distance of about 200 feet from the furnaces, and the gas is collected in an iron tube and led across the yard overhead. It then drops underground into the gas flue, and is distributed to the furnaces. A considerable weight of floor-plates over the valve-pits is included in account 39, but none of the general stock of floor-plates for the mill were charged to the furnaces. In Table No. 1 is shown the money cost of the furnaces as distributed to the several accounts named. In Table 2 is shown the proportion of each account due to each of the several items or classes of expenditure named.. It is thus rendered possible, almost at a glance, to determine the money value in this particular case of each of the items named. The regular work of three of these furnaces in heating steel blooms for the months of January and February, 1877, was 77 rounds per week of 60 blooms each, or 4620 30-foot rails per week. Each furnace will heat 8 14-inch ingots, for three rails each, at one time.

Jan 1, 1879

By Carle R. Hayward

SulphuR has long been one of the banes of the steel manufacturer and often no effort and expense have been spared in order to reduce it to a small per cent. in the finished product. This condition is due to a general conviction that in many cases where steels have failed in service, sulphur has been the cause. But there has been a growing feeling in recent years that the verdict against sulphur has been unnecessarily severe. In cases of segregation it was present in. augmented amounts along with other impurities, but it had not caused the segregation. High sulphur in pig iron is caused by poor furnace conditions and the sulphur is merely one indication of an iron that has not been properly reduced. No amount of subsequent treatment under oxidizing conditions in the open-hearth furnace can remedy the defects, although the per cent. of sulphur may be considerably reduced. In other words, the causes of bad steel can frequently be traced back to bad pig iron, and sulphur is merely one indication that the pig iron is bad. The writer recently visited a steel plant where a mass of evidence had been accumulated which substantiated this fact, and the superintendent was emphatic in stating that high sulphur was not harmful provided the steel was not otherwise poor due to insufficient reduction in the blast furnace. The presence of a moderate amount of sulphur is desirable from the standpoint of the man who machines the steel. The low-sulphur material drags and the production of a smooth surface is very difficult. A slight increase in sulphur enables the machinist to produce a smooth surface without difficulty. Since, therefore, such large quantities of steel are subjected to machining, it becomes highly important that the sulphur controversy should be settled, and if its presence is proved to be harmless the ban on it should be lifted. Among the recent papers on the effect of sulphur on steel is one by Dr. J. S. Unger, Manager of the Central Research Bureau, Carnegie Steel

Jan 1, 1917

W. A. SCHLESINGER,* Denver, Colo.-Two problems are of great interest to the radium manufacturer at the present tine: The first is to perfect a process, more efficient and more economical, which is capable of treating a greater variety of ores. . Practically all the radium now manufactured in the United States is extracted from carnotite ores and these vary a great deal according to their location. The amount of sulfates contained in the ore is of particular importance, and any straight acid-leaching method, such as developed by the Bureau of Mines, becomes prohibitive when the ore contains more than 0.5 per cent. of sulfates, as the sulfates go into solution and naturally precipitate the radium as insoluble radium sulfate. Since the amount of ore obtained from any one claim is usually comparatively small, it is necessary to work a number of claims in different localities, and a process, in order to be commercially satisfactory, should handle all of these ores. In other words, it would be entirely unprofitable for radium manufacturers to employ any process which cannot treat any but sulfate-free ores. He must deal with carnotite containing appreciable amounts of sulfates, and must be able to work this in with the other ores. Carbonaceous ores from certain sections in Utah; which are known to contain as pinch as 1.0 per cent. and more of volatile matters, are prone to a, nitric acid-leaching process. The second problem relates to the treatment of concentrates. There is no doubt that a very large amount of low-grade ore, containing less than 0.75 per cent. uranium oxide, is available. It has been demonstrated that these ores can be concentrated, but there is still room for research

Jan 11, 1918

By A. F. Lucas

The discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has gran with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting; and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable depth along lines of structural weakness; and that a deep well, properly located, stands an excellent chance of discovering the parent reservoir and thus of developing new and probably great supplies. This paper is presented as a discussion—necessarily hypothetical and based largely on personal opinion—of the possibility of encountering deep-seated oil deposits beneath the salt domes. Salt-dome Structure All of the oil produced in the coastal region of Texas and Louisiana is probably associated with salt domes, though in Goose Creek, Edgerly, and one or two other fields no salt has yet been actually penetrated. As

Jan 1, 1920

By O. W. Ellis

In view of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal In the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metal-lic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone arc used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt. Avoidance of Oxidation in Furnace Practice When melting virgin copper in crucible practice, the avoidance of oxidation is not difficult, nor is it hard to forestall trouble in the electric furnace. In gas-fired furnaces of the barrel type, however, the avoidance of oxidation is almost impossible, no matter what the condition of the flame, the flux employed, or the amount of charcoal included in the charge. Copper melted in furnaces of this type is almost invariably so highly oxidized as to requirc very considerable additions of such deoxi-dizers as, for example, silicon copper to render it free from cuprous oxide. As a result,, the castings produced are decidedly inferior, on account of the. large amount of silica which is engendered in the metal as a result of the reaction, Cu2O + Si = SiO2 + 2Cu. The deoxidation of such oxidized copper could, of course, be effected by means of zinc with, however, even more disastrous results.

Jan 1, 1930

By M. E. Wadsworth, G. W. Warren

INTRODUCTION Hydrometallurgical processes for the extraction of metal values can be divided into two broad categories: (a) Processes involving the treatment of high grade material (e.g. finely divided mineral concentrates); and (b) processes which treat lower grade material (ores, waste dumps, etc.). This discussion will be directed primarily toward the first category, but in either case a fundamental knowledge of the intrinsic kinetics and thermodynamics is necessary to understand the behavior of the system. The bulk of research efforts in the last decade along these lines has been aimed at the recovery of copper (1-8). However much information has also been reported on uranium (9, 10) , zinc (11) , cobalt and nickel (12, 13). More comprehensive reviews on these areas are also available (14). As discussed by Sepulveda and Herbst (15, 16) one of the most difficult problems facing process designers is the acquisition and scale-up of reliable information concerning the intrinsic kinetics of leaching systems. The scale-up or modeling of these multiparticle systems is far more complex than that of homogeneous ones. This is due to the numerous rate determining steps which are possible with heterogeneous reactions and the broad distribution of properties of a multiparticle feed such as particle size and mineralogical composition (16). In addition, other factors must also be considered such as interactions between particles, the anisotropic nature of individual particles, the effect of solution chemistry, and electrochemical phenomena. All of these factors must be taken into account, often simultaneously. The thrust of this paper will be to more closely examine how the factors mentioned above can be treated. Some elementary examples of

Jan 1, 1980

By Chauncey L. Berrien

The United Verde Copper Company's mine is at Jerome, Ariz. The orebodies arc of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. Three types of ore are mined; schist porphyry and the so-called "heavy" or "massive sulfide" ore. Approximately 50 per cent. of the total tonnage mined at present is of the latter class. A representative analysis of this ore indicates 42 to 46 per cent. sulfur. Because of the high sulfur content, blasting in this ore is an extremely hazardous operation. not only does it endanger the lives of men who may be in the mine at blasting time but it also becomes a potential fire menace when timber is in close proximity to shots being fired in these massive sulfides. The origin of the fires of 38 years ago, embers of which are glowing to this day, may perhaps be attributed to dust explosions due to blasting in the massive sulfides of those early square-set stopes. Dust Explosions Dust explosions in coal mines are a common source of mine disasters. That such explosions may be of common occurrence in metal mines is not generally known, but it is known that metal-mine dust will explode and such explosions have been investigated by the U. S. Bureau of Mines at the Pittsburgh Experiment Station. Samples of "heavy sulfide" ore from the United Verde mine were used in the tests. After studying the results of the tests it was concluded1 that: 1. Dust explosions were initiated in sulfide ore dust in the gallery with a charge of as low as 75 g. of 60 per cent. gelatin dynamite. 2. The exploding dust generated considerable pressure.

Jan 1, 1930

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By Asheim, Harald A.

Parameter estimates affect both the optimum field development decisions and the economic result. A general methodology for assessment of the effects of parameter uncertainty in offshore development decision situations is proposed, and used to analyze aspects of the initial development situation for the Statfjord field.

Jan 1, 1982

By B. D. Crawford, S. A. Falconer

ONE of the outstanding achievements in connection with this country's war efforts has been the ability of our mining industry to supply from domestic sources many of the minerals of strategic importance that formerly were obtained principally from abroad. In order to meet the war-born demands for these scarce minerals, it has frequently been necessary to develop special methods for treating ores and waste products hitherto considered too low-grade to be workable; and to improve the efficiency of older beneficiation processes. Important in this respect have been the recent technological advances in the field of froth flotation of nonsulphide minerals. Because of the refractory nature of many of these domestic ores, and, in many cases, the limited available technical data regarding their treatment, much research work has been necessary. The following examples describe the procedures and reagents used, and the results obtained, in certain laboratory flotation investigations conducted by American Cyanamid Company's engineers at the Cyanamid Ore Dressing Laboratory on ores containing such minerals as scheelite, manganese oxides and carbonate, ilmenite, brookite, kyanite, garnet, spodumene, mica, feldspar, celestite, fluorite, chromite, corundum, and cassiterite. In presenting these data, we wish to point out that many of the minerals listed have previously been tested, and their amenability to flotation reported, by other investigators-notably those of the United States Bureau of Mines. In some instances the procedures and reagents used in the treatment of some of the following described ores follow rather well-established lines, and with one or two exceptions, the reagents used were well known. However, many of the ores tested did not respond well to simple conventional procedures and it was necessary to adopt special methods of conditioning and desliming, reversal of the usual order of floatability of some of the minerals, multiple cleaning, etc., in order to secure separations. Except where otherwise noted, all numbered and trade-marked reagents mentioned in this paper are marketed by the American Cyanamid Co. or the American Cyanamid and Chemical Corporation. TUNGSTEN ORES Tungsten minerals, vitally important in the war industries of the United States, rank high in the list of those we formerly had to import in order to supply our needs. Most of our domestic ores of tungsten contain scheelite as the valuable mineral. Today there are in the neighborhood of twelve tungsten operations in this country where flotation is used as the main or accessory form of benefication. It has, of course, been known for some time that scheelite and other tungsten minerals respond to treatment by flotation.

Jan 1, 1944

The American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc, shall be composed of constituent parts as follows Section 1 Societies-The Institute shall be divided into three or more Societies as follows a The Metallurgical Society of AIME Society of Mining Engineers of AIME Society of Petroleum Engineers of AIME Other Societies may be formed within the framework of AIME or granted member¬ship in AIME as approved by the Board of Directors Section 2 Divisions and Subdivisions-The several Societies of the Institute shall consist of Divisions as follows a The Metallurgical Society of AIME 1 Institute of Metals Division 2 Iron and Steel Division 3 Extractive Metallurgy Division Any Divisions or Subdivisions which may be formed in the future with the approval of the Board of Directors Society of Mining Engineers of AIME I Coal Division 2 Industrial Minerals Division 3 Minerals Beneficiation Division 4 Mining and Exploration Division

Jan 1, 1960

Executive Committee, Board of Directors Howard C Pyle, Chairman, J L Gillson, Vice¬Chairman, A W Thornton, Elmer A Jones, Augustus B Kinzel Finance Committee, Board of Directors J S Vanick, Chairman, John P Hammond, J W Woomer Investments Gail F Moulton, '60, Chairman, Andrew Fletcher, '62, John M Lovejoy, '61, C R Dodson, ex off as AIME Treasurer, J S Vanick, ex off as Chairman of Finance Committee Endowment Andrew Fletcher, Chairman, N G Alford, W J Coulter, Harold Decker, J V N Dorr, R B Gilmore, J B Haffner, Kenneth Hill, 0 H Johnson, J D MacKenzie, D H McLaughlin, J R McMillan, W S Morris, L F Reinartz, H DeWitt Smith, Wilfred Sykes, J R Suman, C E Weed Honorary Memberships C E Reistle, Jr, '60, Chairman, Grover J Holt, '61, Augustus B Kmzel, '62, (ex off as Past Presidents of AIME) M L Haider, '60, D H McLaughlin, '61, John M Lovejoy, '62, L F Reinartz, '63, Howard C Pyle, ex off as President of AIME

Jan 1, 1959

By K. H. Nimerick, B. E. Scott, F. J. Beafore

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.8°C (O°F). Other applications of FCA include deicing: conveyor belts, idler, idler arms, and other moving parts that have been impeded by ice.

Jan 9, 1979

Jan 1, 1961

The first of the two fall meetings of the Petroleum Division was held at Los Angeles, Oct 1-2 The attendance was the largest at a Coast meeting of the Division The Institute was officially represented by President Lovejoy, Secretary Parsons and George Otis Smith There were four sessions Thursday afternoon and evening, the latter a dinner meeting (both at the University Club), and Friday morning and after- noon, these two in the auditorium of the Edison building Possibly a dozen papers were presented, all of them constituting a valuable contribution to petroleum technology Hallan N Marsh, Chairman of the Division, presided at the dinner meeting at which Dr Smith addressed the members on "The Kettleman Plan m Retrospect," and C M Nickerson talked on the "Buena Vista Hills Cooperative Development Plan "

Jan 1, 1937

By S. S. Clarke

Late in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of Jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of Jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1949

By T. J. Whalen and Michael

The grain shape of the carbide in nickel-bowled ad cobalt-bonded titanium carbides was studied by microgiaphic examination, and the influcence of sintering atmosphere, sintering substl-after, ami the amount of metal binder on the grain shape was determined. If was found that the Carbide grain cross sections in the nickel and cobalt cermets ranged from round to angular, depending on the sintering conditions. The spheroidization of the carbides in both cobalt-bonded and nickel-bonded titanium carbides may be attribicted to oxygen. In the course of studies on titanium-carbide base cermets, various investigators have reported on the shape of the carbide grains, and it was noticed that grain shapes were obtained which were either spheroids, or polygons with rounded or square edges. It was also noted that the shapes of the carbide grains changed with time or composition. skolnickl showed that the titanium-carbide grains. after infiltration in vacuum with nickel tended to spheroi- dize with time. The titanium-carbide skeleton was located on a beryllia plate during infiltration. Gur-land,' who studied the microstructure of titanium carbide-cobalt compacts, showed that the carbide grains are round after 1 hr at 1450oC in a hydrogen atmosphere and angular after 7 hr at the same temperature. Goetzel3 has found that the carbide grains in compacts with a high binder content. 40 to 60 pet. tend to be spheroidized. whereas Blumenthal and silverman4 pointed out that the higher binder contents could yield either round or rectangular grains with rounded edges. depending on the nature of the binder. It is the purpose of this paper to present experi-

Jan 1, 1961

By Keith T. Griffiths

INTRODUCTION The Empress Nickel Mine is situated forty-eight kilometres west of Kadoma in the Zhombe Communal Land of Zimbabwe. The mine came into operation in late 1968 based on a proved and probable ore reserve of twenty million tonnes. The initial production rate was 55 000 tonnes per month from underground. This was boosted to 85 000 tonnes per month in mid 1970 when the opencast operation came into production. The mining method at Empress is sub-level open stoping with main haulages mined at ninety metre intervals and sub-levels at eighteen metres. The extremely wide ore body of up to one hundred metres in width has necessitated leaving extremely large rib pillars and sill pillars in position to maintain mine stability and to act as regional support of the hanging wall. In early 1976 the opencast operation had reached its final economic depth and it was then necessary to increase underground production to 85 000 tonnes per month. Since a large portion of the ore reserve remained in both rib and sill pillars, it was necessary to embark on a positive pillar recovery programme. For this reason it was decided to introduce a sandfilling programme for the mined-out stopes and a modified system of sub-level open stoping with post filling of the lower stopes. ORE BODY GEOLOGY AND GEOMETRY The Empress orebody outcrop has a strike length of nine hundred and fifty metres on a north west - south east axis. It is a steeply dipping (65' - 75') tabular orebody of gabbroic rock which has been extensively altered. The north west - south east strike length of nine hundred and fifty metres on surface reduces to some two hundred

Jan 1, 1983

By Frank Firmstone

IN Chemical Phenomena of Iron Iron Smelting, Mr. Bell gives the weight of materials required to fill furnaces of various sizes at the Clarence Works ; as this differs very much from the weight required for furnaces at Glendon, where anthracite and in agnetic and brown iron-ores are used, a comparison is interesting. Taking furnaces at Glendon of 4800 and 11,900 cubic feet capacity and comparing them with the Clarence furnaces of 6000 cubic feet and 11,500 cubic feet, we find that the 4800 cubic feet at Glendon and the 6000 cubic feet at Clarence required respectively

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984