Search Documents

By S. C. Sun

Most previous work on sedimentation of coal 1 and mineral 2-3 suspensions has been conducted in graduated 1-liter glass cylinders of 6-cm diam. With this type of large container it is often difficult to see through the suspension and tedious to perform a large number of tests. Furthermore, the heavy glass walls and the graduation lines of glass cylinders cause internal and stray reflections, respectively. To obviate these difficulties, an Atlab Emulsion Viewer from Arthur H. Thomas Co. was adopted as an alternative apparatus. Equipment: The viewer," shown in Fig. 1, consists of: 1) a stainless steel frame rack holding 21 flat-bottom Nessler tubes or an ungraduated replica 1.64 cm ID and 1.80 cm OD, 2) a movable masked 150-w lumaline lamp behind the tubes, and 3) a scaled glass panel with 100 vertical divisions in front of the tubes. The tubes are snugly held by springs in slots formed by spacer bars, which also serve as shields to eliminate stray light. The lumaline lamp is mounted behind a slit in a movable housing so that it can be positioned behind the suspension to be examined. The lowest or 100-divi-sion line on the front glass plate is leveled with the upper side of the bottom of all tubes. The scaled portion of each tube, roughly 19 cm high and 40 ml in volume, is used to study coal and mineral suspensions. Procedure: The following procedure was used in many tests. A 1.6-gm sample of dry coal was mixed with 16 ml of distilled water in an ordinary test tube and allowed to stand for three days, with occasional shaking to insure thorough wetting of all particles. The slurry was transferred to a Nessler tube and diluted to 32 ml. The pH regulator and flocculating reagent were added, and the slurry was diluted to reach the uppermost or zero-division line. The tube was immediately stoppered and inverted downward and up again ten times during a period of 35 to 40 sec. The lumaline lamp was turned on during the inversion period. After inversion the tube was quickly returned to the viewer rack. The time elapsed for each 10-division drop of the demarcation line between solid and liquid was recorded by stopwatch until the 80-division line was reached in the zone of compression. Additional readings were taken at 15, 30, and 60 min after settling began. The clarity of the supernatent liquid was observed also. As the settling rate became considerably slower at the 75-division line, it was convenient at this time to start the next test in a separate Nessler tube. This was continued until the suspensions in any number of the 21 tubes were tested. An attempt was made to correlate the experimental results between the Nessler tube and a 1-liter glass cylinder. Table I shows that coal particles settle much faster in the cylinder than in the tube, which has a large wall effect.' The correction factor for the tube impedance is 1.662 2 0.145 at the 40-division line in the hindered settling zone, and 1.614 & 0.139 at the 75-division line in the compression zone. This rough correlation was established by dividing the pulp height of each container into 100 divisions and comparing the settling rates of the two containers at the same divisions. Tests were also performed to determine the accuracy of the viewer. The results, not presented, showed that error was within 10 pct.

Jan 1, 1960

By Ralph C. Holmer

IN the field of mineral exploration, 1956 can be looked upon as the International Geochemical Year. This is not because of unusual developments in geochemical prospecting but rather because of the world-wide effort in geochemistry and the realization that geochemistry is now an established exploration method. Use of mining geophysics has continued to increase. Those extensively employing exploration techniques indicate that developments of the past few years have permitted better programming of methods, from reconnaissance to location of drill- holes. There is greater diversification of methods- reliance is not placed on results of one. However, it is realized that often it is more economical to drill an anomaly than to conduct additional expensive geophysical surveys

Jan 2, 1957

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By J. L. Huiatt, D. G. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated methods of recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite and carnallite. Six sulfate- chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2% to 22.2% K20, and recoveries by crystallization ranged from 85% to 99%. Sylvite flotation from chloride evaporites with amine collector, recovered 90% to 97% of the potash in a concentrate containing 54.3% to 60.3% K20. Fatty acid flotation of the high sulfate evaporite recovered 78% of the sulfate minerals in a 28%-K20 concentrate. Flotation of the remaining chloride minerals with amine collector recovered 80% of the potash in a 59.7%-K20 concentrate. Solar evaporation of 37 854 L (10,000 gal.) of brine recovered 99% of the potash in a crude evaporite containing 24.5% schoenite and 20% sylvite. Flotation in a 45-kglh (100-lblh) continuous flotation unit recovered over 95% of the potash in schoenite and sylvite concentrates, containing 28% and 62.3% K20, respectively. An economic evaluation is included.

Jan 1, 1985

By D. M. Davidson

The drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of IIO ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered and is drained by the Piney and Tye Rivers, which are tributary to the James. Geology The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 4.5° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelson-ite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more pronounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,' the TiO2 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. Sampling Methods and Procedure During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this pos sible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1949

By Hugh M. Roberts

In the spring of 1915, then a 30-year old geologist in the employ of the E. J. Longyear Co., of Minneapolis, Minn., I accompanied prospectors to ex- amine outcrops of supposed nickel ore situated a mile or two in from the shore of a lake in the Kenora district of northwestern Ontario. The deposit proved to be bog iron ore containing traces of nickel. We were stormbound there for three days, a circumstance which gave rise to a tale that was told at our fire one night. It seems that Sandy and Jock, two prospectors, were crossing the bay of a large lake in a canoe. They were bucking headwinds; the waves grew higher. Jock called out from the stern, "Sandy, can ye na pray a little." Sandy pressed his knees a little closer into the bow and, between strokes of his paddle, sought for words, which came haltingly, "Save us this time . . . Oh Lord . . . and we promise . . ." when Jock, peering through the spray sang out, "I would na commit yourself, Sandy, I think I see lond ahead."

Jan 1, 1965

By Leah L. Naugle, H. G. Landau, H. H. Lowry

EVIDENCE has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its "Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,1-12 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends-including coals numbered I to 55b, inclusive -which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or I8-in. cylindrical retorts." In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash; from 2.1 to 15.9 per cent, in moisture from o.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the go coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1941

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By Francis Lucas

EACH year we gather in this auditorium to honor the memory of a. distinguished American metallurgist and educator. I cannot bring to you reminiscences of Prof. Henry Marion Howe as other lecturers have done. It was not my good fortune to enjoy the-privilege of studying and working under his direction. As I have reflected on the published works of Professor Howe, it has seemed to me that his mind was trained on the nature of metals and on the mechanism which produced known but unexplained effects. He was interested in controlling and regulating the causes so as to produce specific effects, useful in serving mankind. I recall an afternoon in May, 1925, when, at the invitation of Mrs. Howe, I visited his former home, Green Peace at Bedford Hills, N. Y. The purpose of my visit was to receive at the hands of the widow an engraving of Professor Howe, a reproduction of a painting from life. Mrs. Howe showed me his study. The walls of this large attractive room, brilliantly illuminated by the spring sunshine, were literally covered with the scrolls of honors and of decorations which had been conferred on Professor Howe by governments, academies, universities, societies and institutions the world over. As we walked about the room, she pointed out the significance of each honor and recited a few details of each occasion. I sensed the pride with which Mrs. Howe, then in the late autumn of her life, told me of her husbands' achievements, of his struggles, of his disappointments and of his successes. There was a surprisingly familiar note in the recital to which I was listening. I 'have found the same theme running as a disconnected thread through the written accounts of the lives of most men of science. We then went to the drawing room to chat for a few minutes before I said my farewells. As we seated ourselves, Mrs. Howe turned to me and asked: "Mr. Lucas, what of this great microscope of yours? Cannot it be applied to the study of disease? What a great blessing it would be if it could be directed to relieve the suffering of mankind."

Jan 1, 1931

By Oliver Bowles

Two striking events marked the year 1871-the establishment of the A.I.M.E. and the beginning of the portland cement industry, the most spectacular of all the nonmetallics in its development. Just as David Saylor's first portland cement, made in a little mill at Allentown, Pa., in that year was the forerunner of a mighty industry, the products of which in 1942 were made in 155 plants scattered throughout the country (having attained a value of nearly $300,000,000), so the Institute from its small beginning has attained a membership of many thousands, likewise decentralized into a series of individual sections of wide geographical distribution. Concurrent with the establishment of the Institute was also the invention of the steam drill, followed by the compressed-air drill about 1904. These mechanical drills were so immeasurably in advance of the hand drill and hammer used previously that quarrying and mining of present-day magnitude could never have been attained without them. Some outstanding occurrences have marked this eventful three quarters of a century. The concrete age, with its enormous demands for cement, aggregates and steel, is of primary importance. Of interest also is the shift of fertilizers from the organic to the mineral field. Nitrates, primarily obtained

Jan 1, 1947

By S. Floreen, H. W. Hayden

The effects of additions of iridium, rhodium, ruthenium, and platinum on the mechanical properties of Fe-C alloys were determined. Each alloying element significantly improved the toughness. The results support the general correlation that substitutional alloying elements that stabilize austenite are beneficial to toughness, but the reason for this improvement is not obvious at this time. The effects of substitutional alloying elements on the toughness of steel has long been a subject of both practical and theoretical interest. Despite the obvious importance of this subject, there has been little progress toward understanding the mechanisms by which alloying elements influence the fracture behavior. In some cases the deleterious effects of alloying elements have been shown to be due to mechanisms such as embrit-tlement of prior austenite grain boundaries or inhibition of cross slip in the ferrite lattice. In other cases, however, the reasons for the change in properties are not clear. This is particularly true for elements, such as nickel, that improve the resistance to brittle fracture. Several investigators'-3 have pointed out that there is a correlation between an alloying element's phase diagram with iron and its effect on toughness. Those substitutional alloying elements that stabilize austenite generally are beneficial to toughness, while ferrite-stabilizing elements generally are detrimental to toughness. The word "generally" should be emphasized, because exceptions to this rule can be found. Nevertheless, this correlation does offer a starting point at which to try to understand the effects of alloying elements on toughness. Thus far only two austenite-stabilizing elements, manganese and nickel, have been considered. In order to test the validity of this correlation several other austenite-stabilizing elements were evaluated. The noble metals, iridium, rhodium, ruthenium, and platinum, have binary phase diagrams with iron similar to the Fe-Ni and Fe-Mn diagrams. That is, each element expands the austenite field, and also higher concentrations of each element produce martensitic transformations at low temperatures. Presumably then, each of these elements should improve the toughness of steel. The present study was conducted to determine if this were so. EXPERIMENTAL PROCEDURE The alloys were made as l-lb air-induction melts using electrolytic iron and commercially pure noble metals. Each heat was initially deoxidized by a carbon boil, and further carbon was added to attempt to produce a 0.05 wt pct C content in each alloy. Before pouring, a final refining addition of 0.2 wt pct A1 and 0.1 wt pct Ti was made to each heat. The alloys were cast in a copper mold to produce ingots approximately 1 in. in diam and 5 in. long. The chemical compositions of the alloys tested are given in Table I. The residual nitrogen, aluminum, and titanium contents were all relatively constant at 0.003, 0.03, and 0.02 pct, respectively. The carbon

Jan 1, 1968

By Nicholas M. Short

Many a geologist or driller has wished he could somehow climb into a borehole to see for himself what fractures looked like. Or why recovery was poor. Or how the bit was actually lost. Now it is possible to do the next best thing to climbing into the hole. TV cameras are being used for a close-up look at borehole conditions. Ever since television was invented, geologists and others interested in subsurface conditions have wanted a TV camera that could be used in the narrow confines of a borehole. But development of such a camera was slow, mainly because of the need for compact size. Not until the late 1950's did the technology of electronic miniaturization develop to a point where a camera satisfactory for the purpose could be put together.

Jan 1, 1963

By J. Offeringa, C. van der Poel

The report describes scaled model experiments on the recovery of oil from porous sands by the injection of miscible liquids [solvents] and the subsequent recovery of the solvents by water flooding. Special attention has been paid to the scaling problem. Scaling rules are deduced and their correctness is checked by carrying out experiments in tubes of various sizes. Data are submitted on the effect of the viscosity ratio oil-solvent on the efficiency of the displacement process, the viscosity ratio varying from 1.5 to 5,000. Breakthrough recoveries obtained when flooding with kerosene as a solvent, are equal to those obtained in water flooding at the same viscosity ratio, indicating that he phenomenon of viscous fingering is decisive. After breakthrough, however, flooding with a miscible liquid becomes much more efficient than a water flood and this is more pronounced as the viscosity ratio oil-solvent is higher. Although high oil recoveries are obtained and most of the solvent in the sand can be recovered by a subsequent waterdrive, a straight flood with miscible liquids does not appear economically attractive because of the large quantities of solvent required. Therefore, a circulation process is introduced, the features of which are described in this paper. Though by means of this circulation process the amount of solvent required can be drastically reduced, the process is not yet economic. SCOPE OF THE INVESTIGATION The recovery efficiency by water flood of oils of viscosities exceeding 50 cp is low. As interest in production of these highly viscous oils is growing at the moment, it was considered worthwhile to gain basic information on the feasibility of first flooding such oils with a low viscous miscible liquid [solvent] and subsequently producing the latter in a conventional way, e.g. by water flooding. The method has the obvious drawbacks that return on the investment is delayed until water flooding has begun and that it requires the investment of a more valuable product to produce a less valuable one. On the other hand, it may be expected that the displacement of one liquid by another is more efficient when the two liquids are miscible than when they are immiscible. As laboratory data on this point are scanty, the present investigation seemed justified. Another argument for carrying out these experiments is that they present a valuable contribution to our concepts of the scaling problem in reservoir engineering studies. Some major difficulties which are encountered in the scaling of the waterflooding process such as the scaling of the capillary forces and the difficulty of obtaining the same permeability characteristics in the model do not present themselves in this case. As the fluids are miscible capillary forces do not play a role and as there is only one fluid phase, Darcy's law is valid in its original form. Consequently it is felt that the scaling rules can be deduced with a greater amount of certainty. An essential feature of the experiments is that they are scaled model ones, which are, however, somewhat

Jan 1, 1955

By C. H. Jr. Herty

THE removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal, or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath.

Jan 3, 1925

By J. L. Gillson

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

CONTENTS PAGE INTRODUCTION AND ACKNOWLEDGMENTS. By George M. Fowler 2 Question 1-Is Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions, Especially in Limestone or Other Dense Rock? DISCUSSION by: A. M. Bateman 10 S. F. Kelly 15 C. H. Behre, Jr 8, 13 G. B. Langford 13 T. M. Broderick 11 H. E. McKinstry 6 R. H. Clarke 13 D. H. McLaughlin 8 J. D. Forrester for M. H. Gidel . . . 4 W. H. Newhouse 13 G. M. Fowler 2, 6, 11 R. H. Sales 6 L. C. Graton 11 Edward Sampson 12 R. D. Hoffman 10 J. S. Stevenson 7 I. B. Joralemon 11 L. B. Wright 2 Question 2-What Are Some of the Chemical and Physical Characteristics in Cer¬tain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? DISCUSSION by: G. W. Bain 17 G. M. Fowler 21 C. H. Behre, Jr 21 L. C. Graton 18 J. S. Brown 16 G. F. Loughlin 18 E. L. Bruce 19 R. H. Sales 19 R. H. Clarke 20 A. K. Snelgrove 20 Question 3-Are There Any Criteria by Which One Can Determine When Min¬ing Operations Have Reached the Roots of an Ore Deposit? DISCUSSION by: J. M. Boutwell 29 G. B. Langford 29 T. M. Broderick 28 G. F. Loughlin 25 E. Y. Dougherty 27 R. H. Sales 24 G. M. Fowler 22 F. A. Thomson 26 I. B. Joralemon 22 Edward Wisser 30 General S. F. Kelly 35 References 36

Jan 1, 1940

By H. Q. Golder

INTRODUCTION The stabilization of slopes is not a design problem. A slope is designed before it is made. For a slope to be stabilized it must already exist. The basic problem has existed for a long time. It started with cuts in soil and rock made in the 18th century during the construction of the canals which were developed at that time, and continued into the 19th century with the development of the railways, and in the 20th century with motor roads and lately open pit mining. It is not difficult to stabilize a slope, but certain questions must be asked and answered. These are: i) How much stability is required? ii) For how long is it required? iii) How important is the cost? These three questions indicate the basic problem of Civil Engineering, which is that the solution to any problem is a compromise between safety, cost and time. Stabilization of slopes is no exception. If the slope exists why is stabilization a problem? There are many possible reasons, for instance, a neighbouring and similar slope may have failed, or it may be necessary to change the conditions of the slope, steepen it, increase its height, put weight at the top, or construct a building at the foot in which case added security is required, or guarantee its stability for a longer time. MECHANISM OF FAILURE In order to pick the correct method of stabilization the mechanism of failure must be understood and the immediate cause of failure known. Often to remove the cause is the best remedy. The mechanism of failure has been studied over a period of many years in landslide problems. Pit slope failures are very similar to some types of landslides. (1) (2) (3) (4) In one sense there are many causes of landslides. Terzaghi lists 19. This means that there cannot be a standard solution to a stabilization problem. In another sense, it can be said that there is only one cause, which is gravity. This is a constant, never failing force which cannot be

Jan 1, 1971

By Kenneth K. Humphreys, F. R. Zachar, A. G. Gilbert

INTRODUCTION by F. R. ZACHAR and A. G. GILBERT Coal producers are not only faced with the problems of mining coal, but must also decide to what extent they can invest capital and what operating and maintenance expense they can afford, after mining, to market their product in sufficient volume and at a reasonable profit. Regardless of whether the operator is contemplating a new operation or merely considering expanding present facilities, market requirements, ability to make a product meeting requirements, probable costs and possible future changes in raw coal or finished product must be considered. In addition, such items as flow sheet, structural designs, storage facilities, etc, must be examined individually and collectively. In estimating preparation costs to meet predetermined market specifications, the operator must calculate the economics of present preparation practices to anticipate the increase to total production which results when the quality of the finished product is increased. The consumers of coal are continually seeking to obtain the best and most adaptable product for their money. Regardless of whether coal is used for coking, industrial requirements, electric power generation, domestic fuel or for other purposes, it will be scrutinized from such standpoints as delivered cost, suitability for utilization in certain equipment, ease of ash disposal, adaptability to material handling system plans and its potential for generating dust problems. Utilities, due to large capacity volume requirements, are generally in a position to select coal that will result in the lowest over-all cost per million Btu. Freight costs, paid by the utility, are important and are given utmost consideration when a coal is under consideration. Steel companies, whether producing or purchasing coking coal, are continually seeking coal that will result in lowering the cost of pig iron production. Since it is usually necessary to clean to lower specific gravities, say 1.40, to turn out a product meeting metallurgical requirements, it follows that a high ash "middling" product is created. These low quality middlings do not command a good price. Therefore, unless the metallurgical coal can command sufficient realization to carry or subsidize the middlings, the operator may be ahead economically to prepare steam coal at a higher specific gravity. While the "unit-train" rate reductions have been helpful to the economy of the coal industry, the establishment of these rates has made mandatory the installation of storage and rapid car loading facilities at mines and plants shipping utility coal (see Chapter 15). A study of the economics

Jan 1, 1968