Search Documents

By Hjalmar W. Johnson

It has long been accepted that blastfurnace practice varies to some degree with the coke used. While the qualities desirablc in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blastfurnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: . Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the pro duction of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. Functions of Coke and Qualities Required to Perform These Functions Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1942

By C. D. Stahl, R. Sandrea

This investigation was made to evaluate the comparative effects of the viscosity and the phase behavior of the buffer fluid in the composite solvent displacement of Bradford crude from waterflooded sandstone cores. Buffer slugs of propane, naphtha and other refined hydrocarbons exbihiting increasingly favorable viscosity ratios and decreasing solubility relationships, respectively, with Bradford crude, were used in long Berea sandstone cores. The secondary slug was isopropyl alcohol. The results indicate that higher oil recoveries are obtained for increasingly favorable phase relationships even when these are accompanied by unfavorable viscosity ratios within the range studied. Moreover, when propane is used as a buffer slug with an adverse viscosity ratio of 36, it gives higher oil recoveries than at a similar size slug of an any1 alcohol having a viscosity ratio of 1.09. The investigation was extended to the study of the effect of flooding rate on oil recovery. Residual Bradford crude was displaced from a 6-ft Berea sandstone core at rates varying from 0.3 to 30 ft/ day. The results show that as flooding rates were increased above or decreased below a minimum range of 1 to 2 ft /day, displacement efficiency increased considerably. INTRODUCTION In recent years, the alcohol slug process as a means of tertiary recovery has been the subject of many investigations. Gatlin and Slobod showed the advantages of the combination solvent slugs over the previous single-slug process.1 The combination slugs require less total slug material to obtain similar oil recoveries. The basic combination process involves injecting a primary or buffer solvent which is preferentially oleophilic, followed in turn by a water-driven slug of isopropyl alcohol. This procedure ensures that the buffer slug, which is miscible only with the reservoir oil, displaces and replaces the oil and is in turn displaced, together with the water, by the isopropyl alcohol slug miscible with both fluids. Likewise, for those reservoir oils that show some degree of phase incompatibility with isopropyl alcohol, as does Bradford crude, a proper buffer solvent can artificially make the alcohol process technically feasible. From an economic standpoint, propane or LPG would be the most appropriate primary solvent to be used in the field; however, Taber, et a12 have indicated that the alcohol process becomes highly inefficient in the displacement of light hydrocarbons because of the entrapment of these hydrocarbons during the stabilized bank formation. Moreover, since materials such as propane have such low viscosities, adverse viscosity ratios with most reservoir oils would be penerated, thereby possibly further reducing the efficiency of the buffer solvent. This paper presents the results of an experimental study of the comparative effects of viscosity ratio and phase relationships on the displacement efficiency of Bradford crude by means of dual solvents. The work was extended to include the effect of flooding rate on oil recovery. Rates within the range of field and laboratory values were used. EXPERIMENTAL PROCEDURE APPARATUS The porous media used in this study consisted of two 10-ft and one 6-ft Berea sandstone cores, 3-in. in diameter. These were cast in galvanized steel pipe of 31/2-in. ID and the annulus was filled with Armstrong cement. The 10-ft cores were assembled by connecting two 5-ft units, which were joined together by 8-in. steel flanges fitted to the pipe. Intimate contact between the two sections was obtained by inserting a thin disk of the same sandstone between the core faces. The outlet and inlet ends of the cores were covered with threaded pipe caps. The injected fluid was gravity fed to two variable-rate positive-displacement pumps. The fluids were filtered before entering the core and the effluent was collected in an automatic fraction collector and

Jan 1, 1966

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting. passed the following resolution: "The Board of Directors, having been appealed to by several Local . Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1937

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By L. F. Mondolfo

An investigation of the relationship between properties of the elements and type of binary diagram formed was conducted. It was found that, for each type of equilibrium diagram, the factors for the size, valence, electronegativity, period, melting point, entropies of fusion, and sublimation calculated for each pair of elements cover a range of values. However, these factors show sufficient relationship to the equilibrium diagram so that the correlation of several of them can be used to predict the type of diagram formed, or at least limit the choice to only a few types. ThE goal of the metallurgist concerned with alloy development has always been to find a method that predicts the properties that can be obtained when a certain metal is added to another one. In most cases a qualitative predictiton of properties can be made if the equilibrium diagram is known. However, this means that for new metals the alloy development has to start with the experimental determination of the equilibrium diagrams. Because this determination is at least as complicated and time-consuming as the determination of the properties themselves, most alloy development has taken place by trial and error, and the study of the equilibrium diagrams has followed rather than preceded the creation of new alloys. Alloy structures and properties depend on the interaction between electrons and a complete knowledge of these interactions would permit prediction of structure and properties of alloys. Unfortunately direct measurement of these interactions is extremely difficult and somewhat doubtful and only properties that depend on them can be measured easily and with certainty. Study of the relationship between properties of the elements and equilibrium diagrams is not new. Besides the well known Hume-Rothery rule of the necessity of an atomic diameter fit within 15 pct for extensive miscibility in the solid, and the wide knowledge of the effect of such factors as size, electronegativity, electron-atom ratio on solid state features,"' work relating to liquid state and liquid-solid reactions can be found in the literature. Of particular interest is the work by Axon,3 who investigated the effect of size and melting point on a selected number of eutectic and monotectic dia-

Jan 1, 1962

By Charles H. Grant

Some of the limiting factors relative to explosive crushing of rock and ways to overcome a few of these problems are presented. Relationships between borehole diameters, bench heights, and spacings, along with a review of the influence geometry has on energy as these are changed, are discussed. Efficiency in use of explosives and the decay of energy as it moves through rock and is absorbed and dissipated, is described, along with fragmentation as a function of spacings and energy zoning, etc. Communications are one of the major problems encountered. In an effort to provide a better understanding of the use of explosives, it is necessary to take a little different view of what explosives are, how to look at them as tools to fragment rock, and some of the problems encountered in doing so. First, take the explosive: although there are many factors involved, consider these as being reduced to only two — shock-strain imparted to the rock by the high early development of energy, and the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc. First, consider shock energy by itself and assume there is no gas effect in the reaction. Fig. 1 illustrates a block or cube of rock, in the center of which is detonated an explosive charge which is 100% shock energy. Tensile slabbing would be seen on the surface and probably the cube of rock would generally hang together even though microcracks were formed. If the situation is reversed and an explosive whch has no shock energy and only gas effect (Fig. 2) is considered, the cube of rock would act as a pressure vessel and contain the pressure from the gas effect until it exceeded the rock-vessel strength; then the rock would break in a few large pieces. If these two kinds of energy are put together and the area of shock-strain around the explosive (Fig. 3) is considered, the two energies will be seen working together to furnish broken rock. The gas effect applies pressure to the microcracks formed from the shock energy to weaken the rock-pressure vessel and propagate these cracks to break the rock apart. It not only will be broken more finely, but will break apart at a lower pressure than the gaseffect case, since the shock energy has first weakened the rock vessel. Although tensile spalling from the shock-strain imparts momentum to the rock, the main source of displacement comes from the gas effect. The term "rock" is being used to mean any material to be blasted. These energies are absorbed by the rock in different ways. First, classify rock into two main categories: "elastic" and "plastic-acting." Elastic rock should be thought of as rock which can transmit a shock wave and is high in compressive strength, such as granite or quartzite. Since this elastic rock transmits a shock wave well, it makes good use of the shock energy from the explosive-forming cracks, etc., for the gas effect to work on. Plastic-acting rocks are rock masses which are relatively low in compressive strength and absorb shock energy at a much faster rate, thereby making poor use of the shock energy by not developing as extensive a cracked zone for the gas effect to work on. Rocks of this type are generally softer materials such as some limestones, sandstones, and porphyries. For the most part, the shockenergy part of the explosive reaction is wasted in plastic-acting rock, leaving most of the work to the gas effect. Since the ratio of gas effect to shock energy is different in different explosives, it is easy to understand why some explosives perform well in elastic rock and poorly in plastic-acting rock, and vice versa. Some of the most difficult blasting situations arise when mixtures of plastic-acting and elastic rock are encountered (Fig. 4). Fig. 4 shows an example of granite boulders cemented together with something like a decomposed quartz monzonite which is plastic-acting. The elastic granite boulders will transmit the shock-strain within itself, but when this shock tries to move through the monzonite to the next boulder, its intensity is absorbed by the monzonite and little shock-strain is placed on the adjoining boulder. In addition to this loss by absorbtion, shock reflection at the surface of the boulder will effect tensile spalling. The net effect is poor breakage of the boulders which do not have drillholes in them as they simply will be popped out with the muck. The same is true (Fig. 5) when layers and joints make

Jan 1, 1970

By S. E. Buckley, M. C. Leverett

THE production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. INTRODUCTION Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,1 and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. ROLE OF DISSOLVED GAS When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1941

IN A broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SiO2, MnO, and other oxides charged as such, and (3) lime charged or fed to the heat to neutralize the “acidic”: oxides present (Si02 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, we have only a somewhat. imperfect control over these factors, so that beginning at about the lime-boil period in the heat, and later in the early refining period, it becomes necessary for the first helper, as the heat progresses, to make quick estimates of the composition and physical state of development of the slag (as well as of the amounts of phosphorus, sulphur, and carbon in the metal) from which he can judge how much extra lime, roll scale, fluorspar, and other additions will be needed not only to give the desired final slag composition, but also to hasten the complete fusion or shaping to a desired viscosity in the liquid state. The discussion in this chapter is limited essentially to those more or less practical rapid methods of slag estimation that have been used, or at least tried, for these purposes under actual open-hearth shop conditions. Another aspect of importance here is the extent to which the freedom of choice to the operator is limited by available charge materials, product specifications, and the oxidation and other chemical- reaction effects which inevitably occur under the conditions of this furnace process. For a better understanding of these control limitations and of the chemical and physical background of the subject, the reader is urged to read at least part of the discussion in Chapters XVII and XIX. Charge materials are discussed in Chapter IV, and many of the details of charging, melting, and refining practice closely related to slag control are given in Chapters VI and VII.

Jan 1, 1944

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper' presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions', and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By Tomek Ulatowski

This presentation discusses the necessary ingredients for the creation of an acceptable credit structure, i.e., the structure that enables the borrower to attract the funding from different groups of lenders. As the amount of debt in the capitalization of new projects increases, it becomes quite critical that the mining venture sponsors obtain funding in a manner which maximizes the project economics. Attention normally is focused on the inherent operating cost characteristics of a venture such as the cost of mining, milling, transportation, smelting, and refining. The projected costs are derived from lengthy feasibility studies often taking millions of dollars and years to prepare. For a variety of reasons as the amount of equity directly provided by the sponsors declines, the balance must be made up from external credit sources. As a result, once the project becomes operational, debt service requirements assume crucial importance. For most new ventures, in the early years of production, the total amount of periodic debt amortization charges together with the projected interest expenses equals or exceeds the total operating cost. Utmost care must be taken, therefore, to reducing these costs which will then increase the chances for the implementation of the project. Project sponsors must carefully evaluate different funding sources in terms of their potential economic impact and, concurrently, evaluate alternative credit structures in order to be able to attract the selected funding vehicles. In this presentation I will discuss credit sources in the order of their relative appeal; i.e., from the standpoint of maximizing rates of return to the project owners. The tenor of the credit, that is the period from signing a loan agreement to the time of last repayment under the loan agreement, is undoubtedly the most important variable in evaluating the attractiveness of debt sources. Therefore, I will begin by discussing debt sources with the longest maturities and will end with a description of credits with relatively shorter tenors. The availability of different funding possibilities will naturally depend on the geographic location of the proposed venture, the creditworthiness of the borrower and the sponsors, the project economics, and finally the actual liquidity conditions in the capital markets at the time that the funds are committed. U.S. LONG-TERM DEBT MARKET - PUBLIC OFFERINGS AND PRIVATE PLACEMENTS The long-lived nature of most mining projects dictates that the majority of the mine financing be raised from long-term sources. In today&apos;s world capital markets U.S. debt issues probably carry the longest maturities available. The maturities can range from 5 to 40 years. Various types of long-term corporate debt instruments can be differentiated from one another by their terms, seniority as to claims against the assets of the issuer, legal form, and whether issued privately or through a public offering. The terms of these debt issues vary widely. For example, the interest rate which is typically fixed at the time of issuance, is determined by the credit quality of the issuer, the maturity, the average life, the seniority of the debt, the quality of control covenants or type of assets pledged as security, and other exogenous factors such as: economic policy, general level of interest rates and cur-rent level of financing activity. The entire principal amount of the debt may be due and payable at maturity (known as a "bullet" maturity) or, more typically, through periodic repayments in equal or staggered amounts. Almost all such debt issues allow for prepayment at the option of the issuer, but require varying amounts of repayment penalties. Disbursements are made over a relatively short period after signing of the debt documentation which may not coincide with the actual funding needs of the project. Financial covenants can be quite stringent, covering areas such as the issuer&apos;s financial leverage, working capital, payment of dividends and other distributions, merger and acquisition activities, and limitations on the disposition of property. Long-term debt issues may also be distinguished by the seniority of their claims against

Jan 1, 1985

Jan 1, 1943

By R. E. Steiner, A. F. Weinberg, R. J. Van Thyne

Uranium solubility in molten bismuth was determined in the temperature range 350" to 600°C, varying from 0.09 wt pct to near 2 wl pct, respectively. Zirconium and magnesium, simulated fission products, and sodium were found to increase or decrease uranium solubility in bismuth in the temperature range 370° to 420°C, depending upon the addition or temperature. Data were obtained by both chemical analysis of samples obtained by filtration from saturated melts and by measurement of the variation of electrical resistance with temperature. IN a study for the United States Atomic Energy Commission, a Liquid Metal Fuel Reactor Experiment (LMFRE) was proposed in which a solution of uranium dissolved in molten bismuth served as both the fuel solution and the primary coolant. It was proven necessary to add other elements to this solution for certain desirable properties: 1) zirconium acts to prevent reaction of the fuel solution with the graphite core (which would result in the formation of uranium carbide) and also to inhibit mass transfer of iron and chromium from the walls of the reactor tubing to cold spots resulting in blockage; and 2) magnesium acts as a deoxidant and prevents loss of uranium. In addition to these intentional additives, other elements entering the solution are: 1) fission products which are a by-productof reactor operation, 2) sodium (the secondary coolant) through possible small leaks in the heat exchange system, and 3) iron and chromium from the container walls. Each of these elements may affect the solubility of uranium in the fuel solution. Since the concept of this reactor is based upon a liquid solution, the relatively low solubility of uranium in bismuth will dictate the minimum temperature at which the reactor heat exchanger can be operated. The solubility of uranium in liquid bismuth and the effect of some additives on this solubility have pre- viously been investigated1-&apos; (more recent results6" became avaliable after initiation of this investigation). However, some discrepancies between the various results have been noted, and also the cumulative effect of the several additions or impurities was not known. This investigation was commenced to obtain definitive results. MATERIALS Analyses of the materials used are presented in Table I. Although ostensibly of extreme purity (99.999 wt pct), the bismuth was found to contain a significant amount of impurities, probably oxides. Except for determination of the binary system, Bi-U, prior to use all bismuth was hydrogen-refined and

Jan 1, 1962

By M. T. Abasov

Among a host of challenges dictated by the explosively developing scientific and technical revolution, the improvement of control and management is one of the most essential problems. This problem is also of far-reaching importance for the oil and gas industries. An oil and gas extracting complex is an involved multilink system characterized by a great number of elements and by intricate interconnections between these elements. Of paramount importance for these systems is the quality of control. Any deviation of the control from the optimum reduces the effectiveness of the system and deteriorates its basic technical and economic factors. In case of large systems, even a relatively small deviation from the optimum may result in considerable material and power losses. Optimization of control of large production systems is therefore one of the basic means to enhance their effectiveness. The present paper discusses a development control problem for a multilayer gas deposit using the method of simultaneous exploitation of several strata by means of a single well. The optimum control is achieved by determining the dynamics of changes in the number of producing wells in a reservoir with regard to the depth of occurrence of these reservoirs as well as the difference in the time of introduction of the wells from drilling and their transfer to another reservoir. A mathematical model was constructed for the problem under consideration and a method was given to solve this problem. The problem was dealt with under the assumption that either each of the reservoirs or a part of them have vertically overlying areas and that there is no hydrodynamic interference between the horizons. It was

Jan 1, 1977

By R. W. Smith, G. W. Delamore, J. A. Spittle

RECENT work by the authors1 has demonstrated that the crystals constituting the equiaxed zone in small ingots originate, on quenching, in the chilled liquid. Whether any partial remelting2 takes place of the den-drites nucleated in the chilled region was not examined. However, the claim3 that this normally occurs, leading to crystal multiplication, has been disputed.4 Thus, for an equiaxed zone to form in the central region of an otherwise columnar ingot, it is necessary to transport crystallites from the chill zone to this region. In view of the work of Uhlmann et al.,5 it was considered desirable to examine the transport process further. Experimental Technique and Results. In the earlier experiments by the authors.1 a stainless-steel crucible 17/8 in. diam, 41/2 in. high, ad containing an alloy of A1-4 wt pct Cu, was quenched from 660°C into a bath of Wood&apos;s metal maintained at 100°C. Under these conditions a central zone of equiaxed crystals was obtained. However, if a 2250-G unidirectional magnetic field was applied for 2 sec immediately following the instant of quenching, or subsequently, the equiaxed zone did not appear. Careful thermal analysis showed that the short application of the field had virtually no effect on the thermal conditions of the melt. It thus appeared that the crystallites which were ultimately to grow large enough to form the equiaxed zone existed in the liquid immediately ahead of the interface, occlusion being prevented by the convective fluid flow induced by freezing from the walls of the cylinder. When this relative movement was prevented by the Lorenz forces induced by the application of the magnetic field, the crystallites were caught up in the rapidly advancing dendrite solid-liquid interface. To test this assumption, a small ingot of super-purity aluminum was partially melted and poured into a heated stainless-steel mold which was then immediately quenched into molten Wood&apos;s alloy. The resulting structure is shown in Fig. 1, and consists of columnar grains with a central fine-grained zone. Thus the unmelted solid present at the beginning of solidification had been transported ahead of the columnar interface. Discussion. There appears to be little or no information available on the interaction of suspended particles with a metallic solid/liquid interface. However, some information is available for transparent organic sys-

Jan 1, 1969

By W. W. Dudley

Inflow of ground water is an important engineering and safety consideration during construction of large openings underground. The initial step in predicting groundwater inflow involves hydraulic tests in exploratory drill holes. Zones within the area of interest are isolated in the drill hole by inflatable packers and are tested by measuring the water level responses to applied hydraulic stresses. These responses may then be translated into significant hydraulic characteristics of the tested rocks such as transmissivity, hydraulic conductivity, hydraulic potential, and storage coefficient by using a type-curve solution. Once the geometry and necessary hydraulic characteristics have been determined for the rock in the vicinity of the proposed opening, a model can be developed using certain assumptions that will lend itself to treatment with available mathematical methods. The mathematical method applied to the model considers conditions of partial penetration and nonsteady-state, leakyartesian, constant-drawdown discharge of ground water. A type-curve solution results in a curve that gives the variation of discharge (inflow) with time. This technique of predicting ground-water inflow has been used in planning construction of cylindrical chambers for use in underground nuclear experiments by the U.S. Atomic Energy Commission. These chambers have been constructed in low-permeability rocks at depths as much as 6000 ft and under hydraulic heads of thousands of feet.

Jan 1, 1973

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith&apos; have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942