Search Documents

By John B. Goddard, David R. Brosnahan

Leaching of uranium in situ from sandstone deposits with ammonium carbonate solution containing dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However, because of their high reducing capacity and their relative abundance, the FeS2 minerals consume the bulk of the oxidant. A pressure leach apparatus was constructed that permitted measuring oxygen consumption by FeS2, best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1983

By Frederic Laist

IN the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast .flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. . The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feed-ing arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged.

Jan 1, 1933

CENTRAL AMERICANIZATION COMMITTEE Chairman, MRS. C. C. BURGER This committee reports progress in drawing up circulars on the. subject of Americanization, to be sent to all the branches of the W. A. A. I. M. E. It is greatly to be desired that all our members should interest themselves personally in work that can be done among the women and children in the mining districts in the way of Americanizing those of foreign birth or extraction; so much can be accomplished by individual interest and sympathy.

Jan 11, 1918

By R. G. Whittemore, R. Derry

Nickel metal, in powder form, has been produced by pressure reduction, with hydrogen gas, of slurries of nickel hydroxide at temperatures up to 250°C. The nickel hydroxide was obtained by precipitation from nickel chloride and nickel sulphate solutions, using both magnesium oxide and calcium oxide. Rates of reduction and yields were determined as a function of temperature, hydrogen overpressure, seed addition, and the amount of alkali used. The mechanism of reduction of slurries obtained from the sulphate system was studied, and major differences between the sulphate system and the previously examined chloride system investigated. Specifically, in the sulphate system, contra the chloride system, no seeding was necessary, plating and densification were virtually absent and only short induction periods occurred. Grades of product are given and the use of this process in the recovery of nickel from laterites is discussed. The selective reduction of nickel from mixed hydroxide slurries and effluent treatment plant sludge has also been examined.

Jan 1, 1973

By Enid C. Plante, K. L. Sutherland

Practical metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. Oxidation Products from Sulphide Minerals Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS > pbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, zns and cus oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe+++and So4- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and SO4- 25.5 mg per liter of percolating solution. Car-michael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagir-nyaka found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disul-hide. Mitrofanov7 suggested that thiO~ulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1949

By J. J. McKetta, O. L. Culberson

Experimental and smoothed data are presented for the solubility of methane in water for temperatures of 77, 100, 160. 220. 280, and 340°F at prejsures to 10.000 psia. The minimum solubility phenomenon exists within this temperature range to pressures of 10.000 psia. INTRODUCTION The study of hydrocarhon-water systems has been extended to the determination of the solubility of methane in water at pressures to 10.000 psia. The experimental apparatus, and the technique. are the same as that previously reported.' - In the determination of the solubility of methane in water, only two phases were present at temperatures between 100 and 340°F. these being the vapor phase and the water-rich. liquid phase. The determinations involved the agitation of methane and water in an equilibrium cell. withdrawal of a sample from the liquid phase, and the analysis of the sample. The experimental value; determined in this manner are pre9ented in Table I and in Fig. 1. Since experimental and analytical techniques have improved since the initial experiments with this equipment, it was decided to repeat the 77°F isotherm determinations.' Fig. I shows that the individual results for this isotherm are much

Jan 1, 1951

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By Robert B. Fulton

It is a pleasure to talk to you about the world economics of industrial minerals on this occasion of AIME's 100th anniversary. In order to fit this topic into the time and tenor of such a session as this where you are hearing subjects equally broad in scope one after the other, I will deal with the subject through the medium of eight minerals selected to illustrate import- ant economic factors. I must admit to some bias in the selection, since I picked personally familiar ones to elucidate facts of life in the industrial minerals business. It is a very interesting field, different in many respects from metals and certainly far different from petroleum. The minerals chosen are celestite, diamond, fluorspar, salt, sulfur, ilmenite, rutile and zircon. Celestite The market for celestite is mainly in the U. S. where it is consumed in the manufacture of strontium compounds for red-colored flares and other pyrotechnics, for the production of electrolytic zinc, for glass manufacture, and for the manufacture of ceramic ferrites. Smaller markets exist in Europe and Japan. Production comes from England, Mexico and Spain, and a new mining operation is being started in Nova Scotia. There is no significant production in the U. S. nor in the other principal consuming countries, except England; so it is mainly an international commodity. Celestite illustrates many of the factors important in the economics of industrial minerals. To have a marketable product, grade and freedom from deleterious elements are important for materials used by the chemical industry. In the celestite used to make strontium nitrate, calcium is the most objectionable of the commonly associated cations. Selling price is adversely affected because nitrate manufacturing costs are greatly increased if calcium is pre sent, hence less can be paid for the raw material. Meeting specifications can add significantly to the vendor's cost; hence a balance must be struck between the producer's capability and the consumer's requirements, permitting a reasonable profit for both. Sizing of industrial mineral products is often important to the consum-

Jan 1, 1971

Jan 1, 1951

By N. H. MacMillan, W. M. Mularie, R. E. Jackson, A. R. C. Westwood

The initial results of a study of the environment-sensitive microhardness and diamond rotary drilling behavior of granite and its constituent minerals quartz and feldspar (microcline)1 have established that many similarities exist between the environment-sensitive mechanical (chemomechanical) behavior of these materials and that of the simpler solids such as periclase, soda-lime glass, and alumina4 studied previously, at least as far as n-alcohol (straight-chain alcohol) environments are concerned. The results of this study (hereafter designated study I) also suggested that the rate of drilling of granite in these environments is controlled by the chemomechanical behavior of its quartz constituent, and is greatest in those environments which impart a zero l-potential to this phase, thereby maximizing its hardness. Now, cationic surface-active species strongly influence the l-potentials of silicate minerals. For this reason they are widely used in mineral separation operations. In particular, dodecyl trimethyl ammonium bromide (DTAB) was found in study I to produce f 0 for quartz at a concentration in water of 107 to 10-4 moles per 1. Accordingly, the influence of dilute aqueous solutions of this surfactant on the drilling behavior of granite also was examined in study I. This revealed that granite could be drilled three to four times faster in 10-° molar aqueous DTAB than in water, and confirmed by experiment the suggestion that granite is most effectively drilled with a diamond core bit in environments which impart a zero l-potential to quartz. According to O'Connor and Buchanan' however, the isoelectric point for quartz in aqueous DTAB solutions occurs at a concentration of .•.•2 x 10-° moles per 1, rather than [101 to 10-1] moles per 1. To confirm the results of study I, therefore, a more comprehensive investigation of the [ ]-potentials of quartz, microcline, and Westerly granite in aqueous DTAB environments has now been undertaken. At the same time an examination has been made of one of the basic assumptions of the current conceptual understanding of chemomechanical effects. In this view, although hardness changes occur essentially instantaneously following wetting of the solid, they are confined to a surface layer at most a few micrometers (µm) deep. Hence, to maximize the influence of chemomechanical effects on bit penetration rate only shallow cuts should be taken. Practical penetration rates are then obtained by increasing bit rotation speed. Experimental l-potentials were determined by the streaming potential technique using an automated rapid-cycling apparatus recently developed by Martin Marietta Laboratory from a design by Somasundaran and Kulkarni. The drilling studies employed 3.2-mm-OD 120-grit diamond-loaded core bits with a wall thickness of ~0.7 mm, and bit rotation speeds of 2200 and 25,000 rpm. The load applied to the bit was independent of the depth drilled in both cases. The 2200 rpm measurements employed the same drill press and puddle drilling technique as used in study I. The higher rotation speed was obtained using a water-driven dental turbine drill. In the case, the surface active fluid was pumped down the axis of the bit to ensure efficient wetting and flushing of the drilling debris from the hole. In both cases drilling rate was measured by the parameter D(200), defined as the average rate of bit penetration during the interval from 150 to 250 sec after drilling commenced.

Jan 1, 1976

By R. W. Jordan, J. Winter, A. J. Goldman

Kirkendall diffusion of copper and nickel atoms across the bond interfaces, as well as oxygen diffusion in the core to the interfaces, are the mechanisms which control the variation in bond strength with annealing time at 1600°to 1800°F in the cupro-nickel clad copper Mint composite. The unequal mass transfer resulting from the high diffusion rate of copper in cupro-nickel compared with that of nickel in copper caused void formation in the core. Small voids also formed in the cladding after short annealing times. These may have been nucleated by nickel oxide particles which are formed by the dissociation of the cuprous oxide in the core and the movement of oxygen to the cupro-nickel interfaces. The bond strength drops to very low values for annealing time up to 3 hr when the void density is greatest. The increase in bond strength after 16 to 72 hr at 1600°F is a result of the decrease in the void density in the cupro-nickel cladding and the growth of grains across the interface. The void density decrease is attributable to grain boundary diffusion of vacancies to the surface. The abnormally large grains in the copper preclude a similar process from taking place in the core. THE solution to many engineering materials problems that cannot be satisfied by using a single metal or alloy is often attained by combining two or more metals in such a way that each component performs a different function, while the composite meets the overall requirements. The Coinage Act of 1965 authorized a changeover from the traditional 90 Ag-10 Cu dimes and quarters to a bimetallic laminate of 75 Cu-25 Ni clad on a copper core. Economic considerations as well as physical, chemical, and mechanical properties provided a basis for the selection of this composite as a substitute for the silver-bearing alloy. An extensive survey of alloys suitable for use as coinage was prepared by Battelle Memorial Institute for the U.S. Mint.1 It was found that the cupro-nickel/cop-per/cupro-nickel composite satisfied the required color, density, mechanical properties, corrosion resistance, electrical properties, and magnetic properties to make it completely acceptable to the general public and the vending machine industry. This investigation is part of a program to determine the feasibility of reclaiming composite scrap by thermally degrading the bond strength of the cupro-nickel clad copper laminate. The composite exhibits bond degradation and subsequent bond improvement during annealing in the temperature range 1600" to 1800°F. A study of the operative diffusion processes and the resultant structural changes was made in order to explain the observed variations in bond strength with annealing time. EXPERIMENTAL PROCEDURES AND RESULTS Bond Degradation. A measurement of the forces required to peel the cupro-nickel cladding from the

Jan 1, 1969

By C. A. Wert, M. G. Coleman

The Zener relaxation in alloys in the a! solid-solution region of the Cu-Ni-Zn ternary system has bear investigated. Of the binary solid solutions that bound this region, Cu-Zn and Ni-Zn exhibit measurable Zener peaks whereas Cu-Ni does not. At constant atomic percent copper, the Peak height drops uni.forinly from the value in the Cu-ZTL binary to zero in CIA-Ali. The cariation of peak ternperatuve with composition is linear. At constant atomic percent zinc, the peak height in the ternary alloys goes through a large maximum as compared with the binary values. The temperature of these peaks varies smoothly with composition. The half-width of the peaks in the ter nary alloys, however, are much larger than those in the binaries. A large enhancement of the relaxation strength of the Zener relaxation in ternary Au-Ag-Zn alloys as compared to the relaxation strengths in Au-Zn and Ag-Zn binary alloys was observed by Firson and ert.' Since this effect was unexpected, the present study was devised to investigate whether enhancement of the Zener relaxation in ternary alloys is a general feature or is particular to the Au-Ag-Zn system. We have chosen the Cu-Ni-Zn alloy system for this investigation. Measurable Zener relaxations are observed in both the Cu-Zn and the Ni-Zn binary systems, but not in the Cu-Ni binary system. A large solid-solution region extends to large concentrations of zinc, making it possible to vary composition of the alloys over a wide range without crossing phase boundaries. EXPERIMENTAL PROCEDURE Two series of alloys were prepared. the first at constant atomic percent copper, the second at constant atomic percent zinc. The compositions of these alloys are shown by the circles in Fig. 1. The alloys were prepared by melting the individual components, each of which had previously been vacuum-melted, in an evacuated quartz capsule in an induction furnace at 1500 C. The capsules containing the molten alloys were quenched in water to reduce coring. Any individual melt which exceeded 0.001 pct weight loss was discarded. The ingots were swaged to a 50 pct reduction of area and annealed for 1 week in an evacuated quartz capsule to aid homogenization. The alloys were then

Jan 1, 1967

By Charles E. Packard

Many coal producers have been faced recently with the problem of arranging their production facilities to accommodate recent trends in the transportation of their product. Each operator is normally faced with a different problem requiring a system to meet his specific needs. It may be that he would be required to load a seven or eight thousand ton integral train each day which would naturally call for a large storage pile, high loading rate, accomplished in a minimum of time On the other hand, it may be that he is faced with furnishing coal to make up one-half of a unit train that is to be assembled twice a week. Whether the problem is large or small, many considerations must be given to each specific problem to be certain that the proper scheme is applied. The operator actually has several choices as to what type of storage and loading facilities he may consider. The storage pile, for instance, may be open type, conical in shape, kidney-shaped, or long and wedge-shaped. It may also be enclosed by steel or concrete

Jan 8, 1964

By John Howe Hall

The recently announced run of three years, nine months and eleven days made by a crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemens regenerative crucible melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators, of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter: Design, nature of refractories, and conditions of operation (including the nature of steel melted); and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to be operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure repeated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of heat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable—and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting time than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted. The figures available, showing the life of furnaces, are for this reason especially not strictly comparative, since the variations in the steel melted undoubtedly affect the life to a greater or less extent. Probably, however, the method of handling is as important a factor

Jan 1, 1914

By Nicholas S. Young

The one million ounce Newrnont Gold loan has focussed attention on gold's new role as a financing vehicle. This paper explains the background of the new role for gold, and details various gold denominated products now available to the mining industry. The discussion highlights the importance of gold-based products, and how they should be used in developing business strategy for gold mining companies. [ ]

Jan 1, 1990

By O. P. Arora, I. L. Caplan, H. von E. Doering

ThE interpretation of X-ray and electron diffraction data obtained in plastic deformation studies of hcp a titanium requires knowledge of angular relationships between crystallographic planes and directions. Rarey el 01.' have calculated both interplanar angles and angles between directions for a number of c/a ratios. This information, although useful for approximate applications, does not provide exact data for specific hcp metals. Recently, Hu2 has tabulated interplanar angles specifically for hcp titanium. The present study augments the existing data on titanium by providing the angles between plane normals and rational crystallographic directions in addition to interplanar and interdirectional angles. These angular relationships were calculated on an IBM 360 Computer using a Fortran IV program.* Cal-

Jan 1, 1969

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By Howard N. Eavenson

In 1926 the Clover Splint Coal Co. acquired a lease on 1793 acres of coal lands situated in Harlan County, Ky. about two miles above the end of the Clover Fork Branch of the Louisville & Nashville Railroad at Louellen. This property contains several coal seams near the foot of the mountain, which are excellent coal but too thin to be very attractive now, and carries about 968 acres of the High Splint seam 1375 ft. vertically above the stream and slightly more than three-fourth mile from it. This High Splint seam produces a high percent- age of large lump, is very low in ash and sulphur, stands transportation and stocking exceedingly well and has an excellent reputation as a high-grade domestic bituminous coal. To develop this tract it was necessary to build an extension of the railroad slightly over two miles long, and, in addition to the usual mining equipment and machinery, to build enough houses, with the necessary store and other buildings, to accommodate all of the employees. The topography made construction expensive, so that it was important to keep the cost as low as possible, in order that the proposition might be financially attractive.

Jan 1, 1932

By H. E. Montgomery

H. L. Burghoff.*—I have a question, Dr. Smith. A number of the alloys you mentioned contain lead, which, of course, is present as discrcte particles. At what level of concentration does lead begin to play an important part in determining these elevated-temperature characteristics ? A. J. Smith.—That is a difficult question to answer because of the complicating features of the alloys that arc lead free. I do not know of any work done on the subject. But for comparison, 85-5-5-5 has about the same characteristics at, say 450°F. as 88-10-2, which is lead free or contains at most 0.30 per cent. Both 85-5-5-5 and 88-10-2 precipitate delta. The specification limit of usage is 406°F., temperature of saturated steam at

Jan 1, 1945

By E. Topuz, G. Faulkner, M. Karmis, C. Haycocks

The Appalachian coal region of Virginia, southern West Virginia and Kentucky and the extreme eastern portion of Tennessee constitutes a unique area of surface coal mining activities. The area contains a number of contiguously placed coal seams, up to a total of fourteen in some places, which vary in thickness from a few centimeters to 2,5 meters. Much of this coal is of high quality, some being the highest grade metallurgical coal found anywhere in the world. The region may be broadly characterized physiologically as a dissected plateau with a relief above the valley floors of up to 500 meters and a dendritic drainage pattern. Up to six seams may outcrop in the hillsides above drainage, many of which have been subjected to contour stripping operations. Prior to the passage of the surface mining reclamation act, little effort was made to reclaim stripped areas. The passage of the strip mining act, including the controversial requirement for returning the land to its approximate original contour, has forced intensive recla¬mation efforts from the mining industry. The wisdom of this original contour requirement has been the subject of considerable debate and litigation, mainly because of its cost, inconvenience, and value of the land after it has been reclaimed. Regardless of whether recla¬mation is carried out, under current practices slope failures do occur. This in effect circumvents the intent of the law and can expose large unvegetated spoil areas, and contribute to hillside erosion and stream silting. Such failures must be eliminated if further costly reclamation efforts are to be avoided.

Jan 1, 1983