Search Documents

By W. N. Lacey, B. H. Sage, J. S. Billheimer

A restricted ternary system made up of n-pentane, tetralin, and a purified bitumen was investigated at 70, 160, and 220 °F. Most of the experimental observations were at atmospheric pressure or at 200 psi." However, some experimental measurements were carried out at a pressure of approximately 8000 psi. It was found that the purified bitumen was precipitated from its solution or dispersion in tetralin by the addition of n-pentane and that the separation occurred at lower weight fractions of n-pentane at the lower temperatures. The bitumen-tetralin solutions show some colloidal characteristics at temperatures below 160 °F when near compositions at which the bitumen separates as a solid phase. At states remote from the phase boundaries and at temperatures above 160 °F these characteristics become less evident. Under these latter circumstances the mixtures tend to follow the behavior of true solutions, particularly in regard to the approach to heterogeneous equilibrium. An increase in pressure appears to increase the solubility of bitumen in tet-ralin-n-pentane solutions. This effect is more pronounced at temperatures above 160 °F than at lower temperatures. INTRODUCTION Asphaltic phases of plastic or solid nature have appeared in numerous instances during the recovery of petroleum from underground reservoirs. Such depositions occurring underground appear to have caused adverse production histories for particular wells or zones. Because of this field experience, it is desirable to understand the factors which influence the formation or separation of the asphaltic phases from petroleum. The problem is unusually complex because the number of true components involved is very large and the details of the phase behavior encountered are difficult to ascertain experimentally. The literature relating to asphalts, asphaltines, and bitumen is voluminous and widespread.' Only those references which are directly pertinent to the work at hand are cited. The separation of an asphaltic phase, hereinafter called bitumen? from naturally occurring hydrocarbon mixtures has been the subject of several investigations.2'3'4'5'6 It has been found that as many as four phases4 may be produced from a crude oil by the solution of a natural gas and propane at a pressure of 1500 psi and a temperature of 70 °F. The separation of bitumen from such naturally occurring mixtures results in at least one liquid phase which is substantially free of high molecular weight components.³ The influence of the solution of lighter hydrocarbons on the separation of bitumen from a Santa Fe Springs crude oil has been investigated. The results indicate that in the case of the methane-crude oil system, the quantity of plastic or solid phase separated reaches a maximum between 0.14 and 0.19 weight fraction methane and then decreases until negligible at higher weight fractions of methane. Similiar behavior was encountered in the case of mixtures of ethane and crude oil. The decrease in the quantity of the solid phase with an increase in the weight fraction of the lighter component appears to result from the formation of an additional liquid phase6 in which the bitumen is relatively soluble. The formation of this additional phase probably occurs at a weight fraction of methane close to that at which the quantity of separated solid reaches a maximum. A comparison of the deposition of bitumen in the field with the separation of asphalts from lubrication oil has been made' and apparently the phenomena are similar. The phase behavior of bitumen also appears to be comparable to that of coal tar."' The chemical and physical characteristics of asphalts and bitumen have been the subject of extended investigations which have been reviewed in some detail by Katz.¹º The conclusion was reached that the dispersion of bitumen in a number of organic liquids was not entirely colloidal since it was impossible to isolate individual dispersed particles even with the electron microscope. However, the evidence appeared to indicate that at states close to phase boundaries the extent of the dispersion of the phases influenced the equilibrium to a greater extent than is encountered in many simpler systems. From earlier study of field samples it became apparent that the phase behavior of bitumen-hydrocarbon systems was unusually complex. It was difficult to characterize in detail the phase behavior involved in naturally occurring hydrocarbon systems, even after a relatively extended investigation. For this reason, the study of a somewhat simpler system which still behaved in a similar manner became desirable. Three major constituents were necessary as-follows: a bituminous solid, a liquid constituent which was a reasonably good solvent, and a constituent in which bitumen was largely insoluble. A sam-

Jan 1, 1949

By Richard H. Terhune

It cannot be said that the development of processes for roasting in Utah has been evolutionary. Some of the best systems were contemporaneons with smelting here, and one of the most primitive methods, pile roasting, is still entrenched, to the exclusion of all others, at one works. This is certainly not because we have not had sulphur, in place and out of place, to contend with, but rather because roasting has not been a necessity, we having, like most other smelting districts in America, a good share of oxidized ores.

Jan 1, 1888

By J. W. Downey, S. T. Zegler

A study has been made of the occurrence of Phases having the Cr30-type structure in ternary alloys having the general composition where B cept for iron and copper all the B components are known to form binary compounds having the type structure. The occurrence of the struc-ture type in the ternary alloys was investigated using optical and X-ray metallography. The results indicate that iron can replace virtually none of the cobalt in at 900°C, but substitutes for nickel in up to the approximate composition tually insoluble in V3Ni and 2) and exhibit complete solubility. At 100 nickel can be substituted for cobalt in VSCo up to the composition solubility; and 3) in the system , two solid solutions having the type structure occur. At the same temperature, 1000°C, V3Si exhibits limited solubility for V3Co but is completely mis-cible with V3Ga. Lattice parameters have been determined for all the binary and ternary phases. The solid solutions are discussed in terms of the atomic size and electronic factors which are thought to influence the occurrence of Cr30-type phases. The binary compounds V3Co and V3Ni were found to form peritectoidally from o phases and a vanadium, the former compound at a temperature between 1000" and 1050°C, the latter between 800°and 900°C. The substitutions of nickel and rhodium for cobalt in V3Co were determined not to raise the superconducting transition of VSCo to a temperature as high as 2°K. The occurrence and stability of binary intermediate phases having the Cr30- or A15-type structure (space group o;, Pm3n) have been discussed in several recent papers . Vanadium forms the struc -ture at or near V3B stoichiometry with all the mem -bers of the cobalt and nickel groups in the periodic table and also with Au, Ga, Si, Ge, Sn, P, As, and Sb. This paper describes a survey of the occurrence of the CrsO-type structure in ternary alloys having the general composition V3(B, B') where B and B' are Fe, Co, Ni, Cu, Rh, Ir, Si, and Ga. The purpose of the survey was to clarify the connection between the position of the B partner in the periodic table and its CrsO-type phase-forming tenden~y.~,~ The survey is part of a broader program concerned with the influence of B-partner substitutions on the superconducting transition temperatures of CrsO-type compounds. The transition temperatures, Tc, of some of the ternary Cr,O-type phases found in the survey are also discussed in this paper. EXPERIMENTAL PROCEDURE The alloys were prepared by arc-melting in an A-He atmosphere and were in the form of buttons, weighing approximately 3 g. The metals used in their preparation were received from commercial sources and were in all cases 99.9+ pct pure. The vanadium was spectrochemically pure except for 800 ppm of Si, 200 ppm of Fe, and 200 ppm of Al. For study of each pseudobinary system at least seven alloys were prepared having the general compositions case of alloys containing gallium, melting losses were small, usually less than 0.3 pct of the total weight of the metals charged for melting. Melting losses were somewhat greater for gallium alloys, ranging in general from 0.9 to 5.0 pct. Ternary V-Si-Ga alloys were chemically analyzed and the results are given in Table I. The analyses show most alloys to be within 2 at. pct of the intended composition. Throughout the balance of the paper the intended compositions are used in discussing the alloys. The cast buttons were annealed within evacuated quartz capsules for times ranging from 3 to 6 weeks at temperatures between 800" and 1000°C and water-quenched. The phases present in the annealed and quenched alloys were identified by optical and X-ray metallography. X-ray diffraction photograms were made with powders prepared from the bulk specimens, by the use of a 114.6-mm-diam powder camera with copper irradiation. The lattice parameter of CrsO-type phases and their standard errors

Jan 1, 1963

By F. F. Sharpless

ARRIVING at Davis Junction, after leaving Portland, we expected to wait for an hour and a half, but found the superintendent of motive power of the Southern Pacific, Mr. Williams, waiting for us with a car, and were immediately taken aboard this and whisked off to Sacramento. After dinner, we were taken to the railroad shops to see their work in reclaiming scrap steel. We saw them draw off the slag from the electric furnace, and later make a casting. At about 11 o'clock, we took the train for Reno. A delegation of the Nevada Section, with Mr. Kirchen and Mr. Rives at its head, met us at the station. Immediately after breakfast, we started for the property of the Comstock Mines Co., where General Bulkeley Wells was to be our host. We had a de-lightful ride out to the mines and through the old city of Virginia, or through what was left of that old city, reaching General Wells' camp at about 10:30. This contains the newest thing in cyanidation and a remarkably fine iron and concrete mill building. After a trip underground, we were called to luncheon, where about 250 sat down. The afternoon was spent in the mill, and we were taken to Gold Hill, which is a part of Virginia City, for dinner, again as the guests of General Wells, who made a consummate toastmaster. Governor Emmet Boyle was the first speaker; he was followed by President Dwight, and then came President William Sproule of the Southern Pacific. A song, "The Engineer," was followed by Senator Key Pittman, Professor Jones of the State University, Mayor Stuart of Reno, and ex-Senator Charles Hend-erson. The president of the Western Pacific and the president of the Pacific Coast Line were there, also many notable operators of Nevada and California.

Jan 11, 1922

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By R. M. Brick

THE Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic prob-lems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segrega-tion. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute con-centration, with a resultant normal segregation or coring effect during freezing. Theoretically, diffusion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions alumimum-copper alloys segregate inversely and aluminum-magnesium alloys segre-gate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By R. H. B. Jones

THIS paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recognizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and development. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation.

Jan 1, 1946

By H. M. Morse

During the year 1942 there were 66 wildcats drilling in Mississippi. One cored in oil sand, the Macro Drilling Company's Longbell No. I in Clarke County, but as yet it has not succeeded in recovering the oil. These drillings broughi to light five salt domes, two of which had heavy oil showing; one drilled by the Magnolia Petroleum Co. in Warren County, and

Jan 1, 1943

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

Jan 1, 1961

By Richard V. Ageton

Salt bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thickness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1938

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1910

Jan 1, 1947

Jan 1, 1920

By Paul T. Allsman

1.1-1. Current Status. The history of surface mining is essentially that of mining coal, copper, and iron ores, and the nonmetallic minerals--clays, gypsum, phosphate rock, sand, gravel, and stone. Table 1.1-1 is a comparison of the estimated world production of crude metallic and nonmetallic ores and coal with that of the United States for 1964, in short tons. It includes an estimate of the quantity produced by surface mining methods. Two-thirds of the 8.8 billion tons are mined from surface, ranging from a third of the coal, half the metallic ores, and nearly all clays, stone, sand, and gravel. In the United States, production by surface methods parallels that of the world with two major exceptions: 74% of copper ore and 90% of usable iron ore are mined from the surface, whereas outside the country less than 40% of copper ore and only 50% of usable iron ore are mined from the surface. In surface mining of both metallic ores and coal, much waste is stripped, but in mining nonmetallics the ratio between waste and ore is small. Assuming that the stripping ratio for surface mining in the United States will apply equally to world production, it is estimated on a weighted basis that over 21 billion tons of waste, or a total of nearly 27 billion short tons of material, are mined annually in the world by surface methods. Data are not available to confirm the assumption for waste stripping outside the U.S., but the estimate expresses an order of magnitude that is worth noting. Table 1.1-2 shows the materials-crude ore, coal, and waste-mined by surface methods and the relation to total mined by both surface and under- ground methods in the United States during 1964. Eighty-two percent of all crude metallic and nonmetallic ores and coal was mined from the sur- face, including 82% of metallic, 96% of nonmetallic ores, and 35% of coal. Copper and iron ore comprise 83% of the metallic ores mined from the surface, and clays, gypsum, phosphate rock, sand, gravel, and stone

Jan 1, 1968

By T. Prof. Ph. D. Egleston

(Read at the Amenia Meeting, October, 1877.) THE copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Hecla Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as "mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently too make it pay. The metal is so uniformly distributed through these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces,, up to many pounds. III one instance, in making an excavation for a cellar of a

Jan 1, 1878

[Officers and Committees of the Society of Petroleum Engineers 1 Officers and Staff of the AIME 2 Officers of AIME Sections Predominantly Petroleum in Membership 3 Society of Petroleum Engineers By-Laws 5 Alphabetical List of Members 9 Geographical List of Members 110 List of Members by Companies 127 Advertisers' Index 137]

Jan 1, 1961

By H. P. Bucker, M. Felsenthal, F. R. Conley

INTRODUCTION In the intensive analysis of core samples from oil raservoirs, there is a recognized need for pore sizc distribution data. Such data, if collected with adequate precision and in sufficient quantity, should contribute to a better interpretation of fluid flow phenomena than is now possible from a knowledge of permeability and porosity data alone. It is hoped, for instance, that pore size distribution data may eventually provide a useful aid for predicting whether a water flood, or other secondary recovery methods. will he successful in a given reservoir.' Apparatus tor measurlng pore size distribution by mercury injection at pressures ranging from 0 to 2,000 psi have been described in the literature.2,3,4 All of these apparatus are somewhat complex and fairly expensive. Furthermore, the callbration of some of the apparatus is not always easy. Great difficulty, for instance, was experienced in obtaining reproducible pressure-volume correction data for the mercury pump shown in one of the references. An apparatus was therefore developed which was less complicated and less expensive than those of previously described designs. This apparatus is, in some respects, an improved version of a previously described low pressure apparatus' (maximum pressure 150 psi) which did not cmploy a mercury pump but instead used a precision bore glass tube for measuring the injected volumes. Tests were performed with the apparatus from vacuum to 2,000 psi and it was observed that the apparatus furnished reproducible pressure-volume correction data. In addition. it was noted that the maximum correction was small. precision of measurement was high. and operation of the entirc apparatus was relatively easy. Although the apparatus was designed exclusively for samples of 1 in. diameter and 1 in, length or smaller, it could be modified without much difficulty for larger samples, if desired. APPARATUS Arrangement of the pore six distribution apparatus is shown schematically in Fig. I. The heart of the apparatus is a steel sample chamber surmounted by a precision bore capillary glass tube. A mercury reservoir is connected to the lower half of the sample chamber. The top of the glass tube is in communication with a

Jan 1, 1957

By F. F. Poland

The purpose of this paper is to describe a new process for the refining of secondary copper-base metals and a specially designed high-temperature electric-resistor furnace used in the process for the distillation of zinc from these metals. The process was used for the conversion of nickel silver to cupronickel and to recover the zinc content in metallic form. It also proved applicable and economical for the treatment of scrap brass for separating and reclaiming the copper and zinc. The relatively large furnace developed for the distillation of zinc is described in detail, for it made economically possiblc the direct recovery of metallic zinc from scrap brass, which is a new step in the processing of such material. Considerable interest has been shown in the utilization of the distillation furnace for other metallurgical processes, where it is of advantage to operate in a controlled neutral or reducing atmosphere, or to avoid having the processed metal in contact with refractories other than carbon, or to operate at temperatures between 3000 and 4000°F. Purpose of Development It was recognized early in the war effort that nickel would become a critical metal. therefore all nickel stock and alloys containing relatively high percentages of nickel were frozen immediately. Among these alloys were considerable quantities of various grades of nickel silver, an alloy containing copper, nickel, zinc, and in some grades lead, also minor amounts of iron, manganese and other constituents. At the time there was no existing plant or process to eliminate the zinc, lead, and minor constituents so as to convert this metal to cupronickel, one of the important alloys needed by the U. S. Navy for condenser parts. Therefore the Bureau of Industrial Conservation of the War Production Board requested the executives of the leading nonferrous metal companies to have their metallurgical staffs study the problem of converting this metal to cupronickel conforming to U. S. Navy Specification 44T40. The composition specified therein is as follows: nickel, 29 to 32 per cent; zinc, 1.00; iron, 0.00 to 0.60; lead, 0.05; tin, 1.20; manganese, 0.00 to 1.00; total of other elemcnts (maximum). 0.50; copper, remainder. The problem in converting these alloys to cupronickel was the elimination of zinc, lead, iron, manganese, and other elements without appreciable loss of nickel to slags or other by-products. Revere Copper and Brass Incorporated, through its Research and Development Department, undertook to solve this problem. A Government-owned plant was built at Rome, N. Y., and there the conversion was made successfully.

Jan 1, 1949