Search Documents

By T. Sterry Hunt

THE essential principle of this new process, now in operation in Chili and in North Carolina, for the extraction of copper from its ores, is the dissolving of the oxides of copper by a hot solution of protochloride of iron and common salt. In the action which takes place, the protochloride of iron is converted into peroxide, while the oxides of copper are changed into protochloride and dichloride, the latter of which, though insoluble in water, is readily soluble in a hot strong brine. From the solution thus obtained, metallic iron throws down the copper in a metallic state, regenerating the protochloride of iron; which is then ready for the treatment of a fresh portion of oxidized copper ore. In the case of slimy ores, the contact of the bath with the ore is effected by agitation in tubs ; but when the ores are granular, lixiviation in large vats is equally efficient and simpler. The hot solutions, charged with chlorides of copper, are digested in tanks with scrap-iron, or better, are made to flow through covered channels containing the scrap-iron, and in their passage lose the whole of their copper; the reaction at the same time evolving so much heat as to keep up the temperature of the liquid. In order to prevent a certain loss of chlorine, which otherwise takes place from the production of some basic ferric chloride in the reaction between the ferrous chloride and the oxides of copper (both protoxide and dinoxide being generally present in calcined ores), a portion of sulphurous fumes from the roasting is made to pass through the regenerated bath before adding it to fresh ore. This has hitherto been effected by injection, with the aid of a jet of steam.

Jan 1, 1873

Jan 1, 1890

By M. I. Kabir, R. S. Schechter, L. W. Lake

This paper presents the development and application of a novel scaling technique that, when used with a streamline model, causes a "bundle" of one-dimensional (1-D) problems to reduce to a single 1-D calculation. The 1-D bundle is the streamline representation of a two-dimensional (2-D) problem. The 1-D calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desktop calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the US Bureau of Mines.

Jan 1, 1986

Jan 1, 1963

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

By Maurice Ewing, L. Don Leet

Assuming that wave velocities in seismic prospecting increase as a continuous linear function of the depth, the authors have derived formulas for computing, from two time-distance observations, the amount of velocity increase, depth of penetration and a graphical determination of the path of the vibrations, and have discussed the ground, reflected and refracted waves. The application of the formulas is illustrated numerically. Earlier Investigations Observations of the energy propagated from the center of an earthquake disturbance have been used to give information about the velocities and paths of elastic waves in the interior of the earth. One method of accomplishing this depends on the use of the times of transmission. Herglotz(7) § and Bateman(3) obtained a solution of the integral equation involved, which determines the velocity of propagation at any point as a function of the distance from the center of the earth, with no assumption as to the manner in which the velocity of the disturbance varies with depth below the earth's surface. The expressions on which the value of the time and the form of the ray of propagation depend contain an unintegrable definite integral, involving the velocity as an unknown function of the distance from the center of the earth. Wiechert and Zoppritz(15) obtained a manageable form for this function by assuming a law of variation which required a constant curvature form for the path within each of a succession of concentric spherical layers of the earth. C. G. Knott(9) worked out the problem for the first time by an absolutely rigorous method from the data of observation (Zoppritz-Turner tables), without making any assumptions as to the functional relationship connecting the speed of propagation and the distance from the earth's center. His method is a numerical solution of an integral equation, giving each velocity and the corresponding distance from the center of the earth in figures.

Jan 1, 1932

By N. J. Grant, Hans Brunner

ThE materials used in this investigation were furnished by the Aluminum Co. of America and consisted of high-purity alurhinum (99.995 pct) and two aluminum-magnesium alloys containing approximately 2 and 5 pct Mg. The compositions of these alloys are listed in Table I. The materials were received as hot rolled 3/8-in. diam rods and were made from the same heats as the materials which were previously used in this laboratory.'j3 The rods were cold swaged to 1/4-in. diam by 1 in. long, and then had two parallel flats machined over the gage length 0.085 in. apart. The test bars were annealed for 10 min at 700° F, and strained 1 pct in tension at room temperature. They were electropolished (80 pct acetic acid; 20 pct perchloric acid, 70 pct concentration) at a temperature of 60°F at approximately 20 v. A grid, transverse or square, spaced 0.2 mm apart, was impressed by rolling a fine threaded screw (128 threads per in.) across the flat surfaces. The depth of the grooves was less than 5 p. For final annealing and grain size control the specimens were enclosed in aluminum foil and sealed in Vycor tubes. Annealing conditions varied from 1 hr at 700° F to 5 days at 1050° F, depending on the alloy content, to give for most of the specimens a final grain size of about 1 mm. This treatment was followed by electropol-ishing as described above. For the test series presented in Figs. 4 and 5 round specimens were used instead of flat ones, and fine machining marks served as marker lines instead of the impressed grid lines. Electropolishing was omitted. The major advantage is that the spacing of the machining marks is only about 1 u as compared to the 200 u of the impressed grid lines, permitting higher precision in strain measurements. Unfortunately the strain annealing necessary for grain size control also resulted in some preferred orientation of the grains. The preferred orientation of three arbitrary specimens was measured by X-ray diffraction methods and the averaged results are shown in Fig. 1. The possible effects of the preferred orientation on the test results will be discussed later. The testing temperatures were 410°, 515", 725", and 940° F, with one exception in the case of the 5.1 pct Mg alloy. Since the solubility limit of this alloy is 520°F, a test temperature of 545°F was cho-se sen instead of 515°F. The selection of the test temperature was based on two considerations: 1) at 900°F and above, extensive grain boundary migration made it more difficult to measure grain boundary sliding; 2) at 400°F and below, there was so little grain boundary sliding that it was again difficult to make precise measurements. The stress was chosen to give a creep rate of approximately 2.7 pct per hr in connection with Figs. 2

Jan 1, 1961

By A. J. Ardell, O. D. Sherby

The elevated-temperature steady-state creep behavior of polycrystalline a Zr was studied in vacuo under constant tensile stress. The experiments were conducted from 660° to 845°C over the stress range 870 to 5400 psi. The steady-state creep rate, is, of a Zr was found to be related to the applied stress, a, and temperature, T, by the equation where C is a constant. Two interpretations of the data are considered, each requiring different values of the parameters ß, Q, and . It is shown that this formula can be derived using Gilman's phenomeno logical equation relating dislocation velocity to the shear stress for the case where dislocation mobility is limited by the nucleation of kink motion. From the fundamental dependence of strain rate on dislocation velocity and the density of mobile dislocations, the factor exp(ßo) can be related to the stress dependence of the dislocation density, and Q to the energy of kink formation. The two interpretations considered are as follows: Case I—the parameters are adjusted so that the equation above describes the data over the entire range of stress and temperature, implying that creep is controlled exclusively by dislocation glide; Case IIthe parameters are adjusted to allow for the possibility that creep is diffusion-controlled at high stresses but glide-controlled at low stresses. For both cases the values of the parameters are within the spread permitted by the data. Factors favorable to the observation of the unusual stress -dependence of i, for a Zr are discussed and it is shown that the anomalously rapid rates of self-diffusion and the low modulus on the principal glide system are primarily responsible for the anomalous creep behavior. Metal-lograflhic observations are presented and discussed with reference to the overall creep behavior. PREVIOUS investigations of the creep behavior of a Zr have been conducted from room temperature to about 500C The results of these investigations are primarily of engineering significance because of the variety of conditions under which they were carried out, and the low testing temperatures employed. Little information is available concerning the fundamental nature of the elevated-temperature creep behavior of a Zr. This investigation of the creep behavior of a Zr above half the melting temperature (the melting temperature, T,, of a Zr is estimated to be about 1860"K was initiated because there are two significant anomalies of the physical properties of a Zr: a) the rate of self-diffusion in polycrystalline a Zr is anomalously rapid: b) both Young's modulus for polycrystalline a Zr and the shear modylus as-sociated with the prismatic slip system { 1010)( 1120) (the principal slip system in a Zr 7) have anomalously large temperature variations The importance of these quantities to the understanding of creep behavior has been demonstrated, and it was hoped that this investigation would provide a critical test of the predictions based upon the analysis of creep data for other pure metals. However, as the investigation progressed it became increasingly clear that the unusual creep behavior of a Zr could not be analyzed in a conventional manner. 1) EXPERIMENTAL EQUIPMENT AND PROCEDURES Two grades of zirconium, designated A and B, were used in this investigation. The analyses, as supplied by the vendors, are presented in Table I. Material A, with a nominal purity of 99.84 pct, was supplied by the Wah Chang Corp. in the form of cold-rolled sheet from which specimens were machined without further fabrication. Material B, with a nominal purity of 99.95 pct, was purchased from the Nuclear Materials and Equipment Corp. in the form of iodide crystal bar.

Jan 1, 1968

NEW MEMBER, The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1915: Members ADAMS, Louis WINFIELD, Supt., Rolling Mills, Lehigh Plant, Bethlehem Steel Co., So. Bethlehem, Pa.. ALLEN, ARTHUR WATTS, Mine Mgr Rodeo, San Juan, Argentina., BALL, EDWIN MARCOTTEL, Mine Supt., Ishkooda. Mines, Care Tenn. Coal, Iron & R. R. Co., H.F.D. 1, Birmingham, Ala. BOLN, CHARLES A., Oil salesman 135 S. 2d St., Philadelphia., Pa. BOYD, DAVID F., Naval Officer Navy Department, Washington, D. C. CAPERTON, GEORGE HENRY Charleston, W. Va. COGGESHALL, GEORGE W., Chem. Engr., Institute of Industrial Research, Washington D C

Jan 5, 1915

By Edward Gridley

Members of the Institute who were present at the Amenia, N. Y., meeting, in October, 1877, will remember their visit to the hematite mines, just west of the village of Amenia, and some of them may perhaps recall the deposit of carbonate ore south of the opening made for the hematite. The smelting of this carbonate during the last few months, has produced an iron that seems worthy of being brought to your notice. A little more than a year ago, at the Wassaie Furnace, Dutchess County, N. Y., we made a few hundred tons of iron from a mixture of two-thirds ram carbonate and one-third Chateaugay ore, hoping that it would be suitable for steel purposes, but as the iron showed phosphorus 0.189 per cent., it, was not offered. This iron looked well and seemed quite strong, and gave good results in malleable castings; but no special tests of strength were made. About February 1st, of this year, we began using two-thirds roasted carbonate, and one-third Chateaugay, and noticing that the iron mas stronger than usual, we had two samples tested, which showed tensile strength of 32,014 and 34,176 pounds per square inch. After our stock of Chateaugay ore was exhausted, me put on one-third ram carbonate with the two-thirds of roasted carbonate, and the first test made of the iron, showed 40,008 pounds per square inch. The three tests given above were made by Mr. A. J. Copp and Mr. E. B. Manning, of the Phoenix Furnace, Millerton, N. Y., on a machine of Riehle Bros., Philadelphia. Since these tests were made, they have broken samples made with all carbonate ore as follows: 39,669, 40,816, 41,882, 42,281, 39,902, and 40,130 pounds per square inch. A test taken from the same bed of iron as the last-mentioned (40,130), was broken by Mr. A. Blass, at Irondale Furnace, showing 40,151 pounds per square inch. A sample broken on the Riehle Bros. machine, at Stevens Institute, under direction of Professor R. H. Thurston, showed 40,000 pounds per square inch. Another sample was broken by Professor Thurston on his torsion machine, and gave torsion 7", and tensile strength of 44,500 pounds. And

Jan 1, 1884

By E. N. Mazza, H. S. Kalish

The effect of sintering types 302, 3028, and 430 stainless steel powder compacts in hydrogen and dissociated ammonia was investigated. It was found that sintering in dissociated ammonia resulted in as much as 0.5 wt pct increase in the nitrogen content of stainless steel even though the dissociation of the gas was complete. Sintering in hydrogen, on the other hand, reduced the nitrogen content of the stainless steel to less than 0.01 wt pct. In the case of the 302-type stainless steel, the low nitrogen content resulted in a material that was largely ferritic, whereas the high nitrogen content rendered the material fully austenitic. Sintering in dissociated ammonia resulted in lower density, generally lower tensile strength, less ductility, and higher hardness than sintering under equivalent conditions in hydrogen. The reduction of oxides on both stainless steel and iron particles was found to be effected by hydrogen partial pressure in the sintering atmosphere. Compacting pressure was found also to effect oxide reduction during sintering. DISSOCIATED ammonia often is used as a substitute'.' for hydrogen in sintering and in annealing, since economic advantages sometimes can be obtained by such a substitution. In addition, anhydrous ammonia contains very little impurity. Thus, dissociated ammonia gas is very dry whereas tank hydrogen often must be freed of oxygen and water vapor prior to use in many applications. The sintering of stainless steel powder compacts as well as bright annealing is well recognized as requiring a hydrogen atmosphere and for the foregoing reasons dissociated ammonia is frequently substituted. It has generally been overlooked, however, that the nitrogen in dissociated ammonia might have an important effect on the sintering process and on the properties of stainless steel compacts. Considered an inert gas in many applications, nitrogen, on the other hand, is very reactive with cer- tain metals. Dissociated ammonia could not be used for hydriding zirconium or titanium. Nitrogen reacts with columbium, tantalum, chromium, uranium, thorium, and many other active metals. Iron and iron-base alloys are, for the most part, inert in nitrogen but there are many borderline cases. It has been reported that stainless steel stabilized with columbium or titanium should not be sintered in dissociated ammonia.3 olybdenum has been reported as reacting with dissociated ammonia to a minor extent.' Although most of the reactions with iron-base alloys are attributed to the action of un-dissociated ammonia and the action of nascent nitrogen, Uhlig4 showed how readily pure molecular nitrogen reacts with and diffuses into 18-8 stainless steel at 1150°C. He also pointed out how readily nitrogen diffuses out of 18-8 stainless steel when heated in pure dry hydrogen, and these thorough investigations on the subject show that commercial stainless steels are nitrogen-bearing, since they are melted in air. The effects of nitrogen in stainless steel, particularly the 18-8 Cr-Ni type, previously have received considerable attention." In 1926, it was pointed out

Jan 1, 1956

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

Jan 1, 1949

Jan 1, 1965

By Karl D. Libsch, Modesto E. Erneta

Both battery design and environmental pressures are forcing the secondary lead industry to consider new and different processes. Trends in battery design are making normal decasing increasingly difficult. Lead in air, sulfur dioxides, and solid/liquid waste heavy metal restrictions are tightening. There is no clearly defined industry trend toward a given process, but it is clear that plants will be larger, less labor-intensive, and automated.

Jan 1, 1977

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

This discussion of the paper of Chester W. Washburne should have been printed following the remarks of H. A. Wheeler, in Bulletin No. 100, April, 1915, pp. 835 and 836, but was inadvertently omitted. ROSWELL H. JOHNSON:-There is one reason why the hydrostatic interpretation of gas pressure is not wholly acceptable. As we go clown in the sands we seem to get excesses of gas. Particularly in this field it becomes excessive in quantity relative to the amount of water in the sand. If this holds in other fields as well it must mean that there has been an ascension of water, because these sedimentaries when laid down, were filled with connate water. If we do get an ascension of connate water, produced by some such phenomena as its expansion by heat or by the formation of new gas by pressure upon organic materials at great depth, we can hardly expect the pressure to be controlled merely hydrostatically. * In reply to Mr. Wheeler's inquiry as to gas wells with pressure higher than hydrostatic pressure, I would cite the original wells given by Orton on which he based the hydrostatic theory. He used in his calculation a head of 600 ft. above tide, assuming the outcrop of the Manitoulin Islands to be in Lake Superior, whereas the Trenton does not outcrop at Lake Superior. The Manitoulin Islands are in Lake Huron, the level of which is 580 ft. above tide. No allowance is made for the lower density of the fresher water near the outcrop, the weight taken for the whole column being the water of high density found at the wells.

Jan 5, 1915

By R. F. Mehl, W. Batz, C. Wells

Diffusion coefficient values for carbon in austenite covering a wide range of temperature and composition have been determined employing statistical methods. In addition, the relation between concentration and each of the following, D (diffusion coefficient), Q (activation heat of diffusion), and A (the constant in the diffusion equation), has been obtained. A study of the rates of diffusion of austenite was published in Metals Technology in 1940.' The present investigation is an extension of the earlier work, undertaken (1) to obtain values of the coefficient of diffusion, D, over a much wider range of carbon concentration, and (2) to provide data in all ranges of concentration and temperature in such abundance that statistical methods could be employed to evaluate the accuracy of the data with unusual precision. Composition of Materials: Composition of materials used in this research program are listed in table I. These materials, all forged to about 1 1/4 in. rounds, consist of a high-purity iron, Armco iron, a large number of laboratory-made plain carbon steels containing amounts of impurities normally expected in high-quality commercial steels, and three silicon steels. Since it was known at the time these steels were being made that impurities in the amounts present were unlikely to affect carbon diffusion rates' significantly, the effort made to obtain high-purity steels was not as persistent as it otherwise would have been. Procedure: In general, the procedure followed by Wells and Mehl and described' in detail in an earlier publication' is the one used by the present authors. However, certain modifications have been made which it is believed allow diffusion data to be interpreted more objectively and correctly. These are described completely under appropriate subheadings which follow. Experimental Procedure: Experimental procedure includes (1) the preparation of specimens by welding steels of different carbon contents, (2) the heating of these for certain times at selected temperatures in order to diffuse carbon along the specimens across the welded "interface," and (3) the determination of the carbon distribution across the diffusion zone. Preparation of Specimens: Prior to welding steel of one carbon content to iron or steel of another carbon content, surfaces to be welded are machined perpendicular to the longitudinal axis of cylinders which are about 3/4 in. in diam and 1 1/2 in. long. The prepared, flat, parallel surfaces are brought together and butt-welded electrically. Evidence of a good weld is given in fig. 1. Welding temperature

Jan 1, 1951

By Edward J. Felten

THE oxidation resistance of chromium and Fe-Cr alloys is increased by small additions of yttrium or other rare earth metals.1,2 In addition, the presence of the additives increases the resistance of these alloys to spalling of the external oxide above 1000°C. This ability to prevent spalling appears to be related to the formation of an internal oxide in alloys containing yttrium or the other rare earth metals. The internal oxide is found in the form of a filamentary growth concentrated in the grain boundaries of the unoxidized metal. In alloys containing yttrium this internal oxide was found to be either Y2O3 Or YCrO3.' In an earlier report,' the growth of the external oxide was found to be controlled by diffusion through the oxide layer. Thermal balance studies were used to establish the kinetics of external oxide formation. In this related study the rate of growth of the internal filamentary oxide has also been studied. The results obtained indicate that the growth of the internal oxide is also diffusion controlled. Internal oxidation appears to occur in at least two ways. Using copper alloys containing small amounts of silicon, Rhines 3 found that between 600" and 1000oC a subscale was formed which consisted of particles of silica dispersed in the metallic matrix. The conditions requisite to internal oxidation as suggested by Rhines are: 1) a solubility of oxygen in the alloy, 2) the ability of oxygen to diffuse at an appreciable rate into the alloy, 3) the possibility of the formation by the alloying element of an oxide more stable than the oxide of the host metal, and 4) a relatively low solubility of this oxide in the metal. These conditions are fulfilled for a number of other copper alloys.3-5 Furthermore, the relationship between the depth to which the internal oxide is formed and the oxidation time follows the simple parabolic law.6 The activation energy for copper containing small amounts of silicon, germanium, iron, or manganese as calculated from Rhines data6 is about 48 kcal per mole. In some cases the internal oxide is found segregated at the grain boundaries, especially near the the surface. Observations of this type of oxide formation have been reported by stead,7 Rhines,* and Lustman. Evans" cites these cases as examples of the simultaneous movement of anions and cations during oxidation. Furthermore, Evans states that the presence of a minor constituent with a high

Jan 1, 1962