Search Documents

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By D. S. Newton

Introduction Historically the production of zinc dust has been based upon residual and secondary zinc. Using horizontal retorts filled with diecasting scrap, galvanizers drosses and sweater billets, dust has been produced by condensation into static condensers on a 24 hour cycle. Although fairly flexible as regards input materials the process is not amenable to close control of the product, is labour intensive and unless carefully run can cause fume problems. With a steadily increasing demand for zinc dust of consistent properties and higher quality there is a demand for an improved method of manufacture in which dust can be produced continuously and which is capable of close control thus ensuring a minimum amount of oversize or unsaleable material. The Process in use in the works of Imperial Smelting Corporation (Alloys) Ltd. in England, and in Canada and Holland, satisfies the criteria stated above, and has proved to be easy to control with a minimum labour demand.

Jan 1, 1970

J. S. UNGER,*Pittsburgh, Pit., (written discussion?).-From the subject of the paper it is natural to expect that the data presented must be results secured from an open-hearth furnace working under normal conditions, but such is not the case, as the conclusions are based on the results of laboratory tests, which do not approach service conditions. The early basic hearths were made of burnt lime, then followed burnt dolomite, bricks made of calcined dolomite and a 'binder, usually tar, and finally magnesite bricks covered with a layer of sintered magnesite. When this material became scarce, special dolomitic refractories were used. In the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in the resistance to slaking and to corrosive slags. It is well known that neither pure lime nor magnesia has much value as a refractory. By the addition f fluxes, such as silica and iron oxide, lime is rendered inert to slaking in the same way as are the special dolomitic refractories. An example on a large scale is the ordinary basic open-hearth cinder, produced every clay, which does not slake. Pure magnesia, regardless of the lime content, is not any better fitted for a refractory than pure lime. The pure natural varieties, such as Grecian or Washington magnesites, must be burnt with sufficient silica and oxide of iron to produce a satisfactory material. Grain magnesite, either artificial or natural, is, not used in burning in a hearth in the state in which it is received. To make a satisfactory hearth, it must be made more impure by adding about 20 per cent. of basic open-hearth cinder, otherwise it will-not remain in place.

Jan 5, 1919

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.'-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4'5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,'-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

PRESIDENT AND DIRECTOR DONALD B. GILLIES CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS R. C. ALLEN CLEVELAND, OHIO D. C. TACKLING SAN FRANCISCO, CALIF. TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. PAUL -D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. WILLIAM B. HEROY HOUSTON, TEXAS HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1939

By C. O. Ensign

Results of the application of geo1ogic knowledge to grade control have been remarkable. Grade reduction from dilution has been diminished from greater than 9% at the time of the program's beginning to about 2% at present. This has resulted in an increase of about 1.8 lb of copper per ton of ore mined and has made a substantial contribution to earnings at White Pine during the past two years. Even more improvement is expected in the future. The White Pine orebody, situated in the southwestern portion of the Keweenaw peninsula of upper Michigan, is a gently dipping stratiform or bedded deposit. Copper distribution is stratigraphi-cally controlled with higher values being confined to specific beds in the ore column. Room-and-pillar mining is practiced. Mining technique and geologic characteristics present a special array of problems in controlling the grade of ore. A routine program of grade control was started in the White Pine mine in August 1961. The program is based upon development and application of geologic knowledge to assist mine operating personnel to increase the grade of ore, primarily by accurate stratigraphic control and selection of areas for development on the basis of grade distribution trends. Geologists work closely with mine supervisors to offer the necessary geologic guidance. STRATIGRAPHIC POSITION OF COPPER The important rock series in the White Pine area is comprised of three formations of late Precambrian age. In descending order they are the Freda sandstone, Nonesuch shale, and Copper Harbor conglomerate. The Nonesuch shale is about 600 ft thick. Economic copper concentration occurs only in the lowermost 20 to 25 ft of the formation; however, within a restricted area along the southwest side of the mine the uppermost 1 to 7 ft of the Copper Harbor conglomerate (lower sandstone) contain sufficient quantities of copper to be included in the ore column. The ore consists primarily of chalcocite with subordinate native copper disseminated in shales, siltstones, and sandstones. MINE BOUNDARIES AND STRUCTURE The mine area is bounded on the west by the sub-outcrop of basal Nonesuch at bed rock surface and on the southwest by the White Pine fault (Fig. 1). The south and southeast limit of the orebody is reasonably well delineated by thinning or pinch-out of favorable host beds. Northern, northeastern, and eastern limits have not been established. The White Pine fault is actually a wide zone of shearing which strikes approximately N 40° W. It is downthrown on the southwest side and dips steeply to the northeast. Maximum vertical displacement is about 1500 ft.

Jan 1, 1964

By Johnson Crawford, Alan H. Hoagland

Zinc mining at Jefferson City began in 1854 with small scale production of oxidized ore from open pits. Significant production began in 1913 with the development of the Mascot Mine by the American Zinc Company. In 1965, four flotation mills were treating crude ore at the rate of about 12,000 tons per day and the Mascot-Jefferson City district currently is the largest zinc producing area in the United States. The producing mines, Mascot, Young, North Friends Station, New Market Zinc, Grasselli, Davis-Bible, Coy, and the Jefferson City, are 15 to 28 miles northeast of Knoxville in the Valley and Ridge physiographic province, an area of gentle relief lying between the more rugged Great Smoky Mountains and the Cumberland escarpment. The ore is strata bound, occurring essentially within a stratigraphic range of 200 feet in the Lower Kingsport and Upper Longview formations of Lower Ordovician age. In the lower strata of the mineralized section, the ore generally is found in coarsely crystalline elastic dolomite breccia containing silica and chert debris within a sequence of aphanitic limestones. The upper strata of the mineralized section are fine-grained primary dolomites that, in the ore zones, have been fragmented in mosaic patterns by solution collapse with the interfragmental space filled by white gangue dolomite and sphalerite. The mineralogy is unusually simple, sphalerite being the only important sulfide. Pyrite is very sparse. Dolomite gangue is abundant, silica was deposited in quite small amounts, calcite is minor, and fluorite and barite are very rare. The principal ore controlling structures are rubble breccia zones that were formed during the post-Lower Ordovician-pre-Middle Ordovician erosion interval by supergene solution as a phase of the development of a regional karst system of underground drainage that extended to' depths of at least 800 feet. The major Appalachian orogenic structures are post-ore and have been superimposed on the ore bodies. There is substantial evidence to support the current thinking of the writers that the ore deposits were formed at a depth not exc1~eding 800 feet.

Jan 1, 1968

By R. V. Ramani, G. W. Luxbacher

Computer simulation of mine ventilation system is rapidly becoming an essential tool in mine planning and design. This Paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve primarily for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1980

By F. W. Clark

At the present time, when lixiviation versus amalgamation is being so thoroughly discussed by practical men, and published information is so meagre, the following tests, made by students in the mining laboratory of the Massachusetts Institute of Technology, may be of interest to others. The ore experimented upon was obtained from the Sombrerete mines near Zacatecas, Mexico. A careful analysis of the dried sample resulted as follows : Per cent. SiO2,............62.79 S.............13.86 Al2O3............4.39 Fe,............11.26 Zn,............1.57 CaO.............2.91 MgO,........... 0.06 Cu,.............0.12 Pb,.............0.40 Sb and As,..........trace CO2,............2.35 Ag,.............0.16 99.87

Jan 1, 1886

By E. E. White

I DISAGREE with Mr. Brinsmade on several points, and I will discuss his remarks under the same six topics which he has used. 1. Rate of Interest Earned by Sinking-Fund.-I believe Mr. Brinsmade is confused in his ideas as to the effect of new gold on the interest earned on money. The flood of gold which he mentions certainly should not operate, to increase interest rates, but since it replaces and adds to liquid capital should reduce interest rates and counteract the destruction of liquid capital which he mentions. Furthermore, it is doubtful if the destruction of capital since 1897 by wars and catastrophes has been any greater in proportion than in similar periods before 1897. With regard to savings banks, I would say that only 3 per cent. is allowed on deposits through a large part of the West. As to bonds, they can be bought to yield any rate. of interest desired up to 6 per cent., but, a 5 per. cent. bond is not as safe as a 4 per cent. bond, nor a 4 per cent. bond as safe as a 3 per cent. government security. I do not understand why Mr. Brinsmade says that Mr. Denny's quoted opinion of a 3 per cent. rate is evidently based on English conditions before the Boer War. Certainly there is no reference to the Boer war or to English conditions in Mr. Denny's article. M. Howard Burnham, in his admirable work on mine valuation, says': ". For instance, redemption is taken at 3 per cent., because even 4 per cent. represents a greater risk, as is indicated by the purchase of Government paper to bear only 3 per cent., the great desideratum of the .latter being security." . Again, Mr. Burnham says:2 "The tables are calculated on the assumption that the dividends shall accumulate at 3 per cent. only, as in accordance with the general idea set out elsewhere, a rate greater than 3 per cent. involves appreciable risk with which it were inaccurate to saddle the sinking-fund if risks are to be segregated, this being the basis of all the writer's calculations."

Jan 6, 1914

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

By William Fink

ALUMINUM forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has, been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.2 Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560° C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550° or 560° C.; in fact, some of the specimens were the identical ones used by Dix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1930

By Luis E. Vallejo

Experimental and theoretical analyses are presented to study the mechanics of growth and interaction for three inclined left-stepping, three inclined right-stepping and two inclined non-stepping cracks in a brittle material subjected to uniaxial compression. It was found that the non-stepping cracks did not interact and they propagated individually in a direction parallel to the uniaxial compressive stress. The propagating cracks formed in regions where tensile stresses developed. The left-stepping cracks interacted and formed branching cracks as a result of failure in tension of the material between them. Also, they propagated from their tips in a direction parallel to the uniaxial compressive stress. The right stepping cracks did not interact, but extended themselves from their tips following a direction parallel to the uniaxial compressive stress. The extended cracks formed in areas of compressive stresses.

Jan 1, 1984

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.' By means of electron diffraction,' it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).' The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.' Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By T. W. Lippert

In these opening remarks, I will endeavor to give a background of continuous casting of metals. Only passing attention will be given to the different processes to be described by the authors whose papers are on the program, as they are far more familiar than I am with their subject matter. Suffice to say that over the past several years the brass, copper, aluminum and magnesium industries have shifted practically completely from conventional static molds to continuous casting machines. The Aluminum Company of America alone has more than 60 continuous machines in operation. The product as continuously cast is superior metallurgically, less scrap loss is involved, costs are generally lower, and the equipment requires little floor space. A continuous machine, operating as it does with deadly constancy, is a ravenous consumer of molten metal, and in most plants one or two machines are well able to handle large banks of melting and refining furnaces. In steel, interest in continuous casting is today more serious than ever before in history, and there is every reason to believe that continuous machines may secure a minor place in the ferrous industry, particularly for tool and alloy analyses. In the past, steel has been commercially cast continuously, and today many tons of steel are being turned out in this manner. It has been said that the cradle of every science is surrounded by dead theorists— and certainly there are innumerable examples of this in the metals industries. An excellent illustration, for instance, is the continuous rolling of metal, a tantalizing objective that for decades on end exhausted . the efforts of a long line of famous, infamous and unknown inventors. Finally, in 1922, John B. Tytus, of the American Rolling Mill Co., brought forth what now seems such an obviously simple scheme— a concave roll face, each stand of progressivcly less concavity. And out of this one change in design sprang today's wide continuous mill rolling steel sheet Ioo in. wide at 2000 ft. per minute. Another excellent example is the con- . tinuous casting of liquid metal into an intermediate form, preferably one requiring little subsequent breakdown. First, the casting of liquid metal alone was fascinating enough. Then someone passed the cast metal directly into a rolling mill, and shortly thereafter this continuously rolled strip was passed directly into a stamping machine. This leitmotiv of a continuous flow of metal from the liquid phase to a consumer end product, fast and inexpensive, and all housed within a small space, was enough to drive some 200 or so inventors into frenzy over the past hundred years. All the ideas, however, like mayflies, had only their brief afternoon of existence. They were born and they died on paper, as constant exemplification of that great void that always exists between mental production and commercial production.

Jan 1, 1945

This is a brief account of the history of unit operation in the Salt Creek field, Wyoming, from the time of the agreement to prorate production in March, 1921, to the present. An attempt has been made to evaluate the savings in development and production costs resulting from the unit plans adopted. Summarized, these savings have amounted to $11,650,000. No effort has been made to estimate any increase in ultimate recovery, for it is believed that unit operation can be justified on saving in development and production costs alone. It would require nearly 20,000,000 barrels of additional oil to be produced in order to return the amount saved by not drilling unnecessary wells. Four horizons are affected by unit or near-unit programs, as follows: The principal operator is under contract with six companies to operate 10,400 acres. This includes all of the productive area of the First Wall

Jan 1, 1930

By Joseph Hartshorne

This plant is situated in the borough of Pottstown, on the banks of the Schuylkill river, between the Philadelphia and Reading Railroad and the Schuylkill Division of the Pennsylvania Railroad, on a plot of about 125 acres, most of which is reserved for future extensions. About 45 acres are to be used for houses, 40 of which have already been built. The accompanying plan will give a clear idea of the general arrangement of the works. Beginning at the lower or eastern end, the first building is the basic-cinder grinding-plant. At present, it consists of a 2000 mm. Jenisch ball-mill (Kugelfallmühle) similar to those used so extensively for grinding basic cinder in Europe. It was built by Herman LÖhnert, of Bromberg. The mill is very simple in design, and efficient in execution. About 13 horse-power is required to run it, and the average output is 20,000 pounds in 10 hours. The best work we have done is 29,000 pounds in 10 hours, with perfectly dry cinder. From 95 to 98 per cent. of the product will pass through a sieve with 100 meshes to the inch, while from 70 to 75 per cent. will pass through a 150-mesh sieve. The mill has been in service since last March, part of the time on double-turn, and the renewals and repairs have been very slight. The product of the plant is sold as a fertilizer. It runs from 18 to 24 per cent. in phosphoric acid, about 14 of which is reverted. The merits of this fertilizer were explained by Mr. W. H. Morris, at the Baltimore meeting of February, 1892 (Trans., xxi., 232), and by Mr. W. B. Phillips, at the Birmingham meeting of 1888 (Trans., xvii., 84). The results obtained by its use in Europe, where over 600,000 tons were used last year, are well known. Near the cinder-grinding plant will be situated the new machineshop, which is now being erected. The next buildings contain the brick-making plant and ovens.

Jan 1, 1893

By H. Krueger, H. N. Hersh

USE of autoradiography in diffusion studies offers the advantage that no repeated sectioning is necessary and that the analyses are performed in a simple manner over the continuous range of penetration depths. As part of a program of solid-state physics, it was desired to develop the autoradio-graphic method' quantitatively for use in diffusion studies. Results are reported here for the self-diffusion of silver. Silver was chosen because the existing data are good enough to evaluate the technique." The silver used in this investigation was obtained in the form of ¼ in. diam rods of polycrystalline material, 99.99 pct purity. The radioactive silver, Ag110 (ß, y), was obtained as the nitrate and converted to the chloride for use in a standard cyanide plating bath. The diffusion specimens were 1/2 in. lengths of the rod. They were mounted in bake-lite and the exposed circular face carefully ground and polished. Prior to electrodepositing radioactive

Jan 1, 1956

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By George E. Aiken

Modern high speed bucket wheel excavators (BWEs) can dig materials which power shovels can't handle without blasting. Yet these machines are not used in any large, open pit ore mines in the United States. American mining has been slow to use the wheel's special capabilities of high production volume at low cost, due perhaps to a traditional familiarity with shovels and draglines and/or the lack of data of BWE operation, design and cost. Of course, shovels and draglines can not be replaced by BWEs in all cases, but under suitable conditions bucket wheels can out-perform other conventional excavators and simultaneously permit significant operating savings. The latter aspect will become increasingly important to American mining men because as more low to medium grade orebodies are found in regions of thick overburden, better and cheaper ways of uncovering them must be developed. Typical of such areas are the thick alluvial fans of the Southwest and the glacial drift areas in northern regions. Much of this material would handle well with a wheel excavator without blasting, although ripping might be necessary in some cases.

Jan 1, 1966