Search Documents

By J. L. Bray

IT is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-alumi-num system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1. Others2,3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to

Jan 1, 1936

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By V. R. Degner

The trend in both the metallic and nonmetallic mining industry is toward processing increasingly higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This Paper reviews the R&D approach used in translating smaller flotation machine experience to the configuration of a 28.3 m3 (1000 cu ft) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1981

By George A. Komadina

The Pima mine lies 20 miles southwest of Tucson, Ariz., and 45 miles north of the Mexican border. It is located on a hillside overlooking Tucson, which allows for gravity flow generally through the plant. In April 1965, an expansion was authorized by the mine's board of directors. This will triple the mine's output to 18,000 tpd. At this rate, it is estimated that there is sufficient ore to last 20 years.

Jan 6, 1965

By W. T. Turrall, D. Porter

THE crystal laboratory, Dept. of Physics, Massachusetts Institute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF2) for use in growing synthetic CaFe2 crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF2 crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO2, BaSO4, CaCO3, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, -4 mesh +10 mesh, from a feed containing over 99 pct CaF2. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1952

By Stephen E. Erickson

MORE and more hydrocyclones are being installed in beneficiation plants. This recent rapid increase is of special interest in the history of beneficiation, since development of the hydro- cyclone appears to have swung in a circle. To avoid any chance of confusion, it would be well first to review the accepted definitions. The size of a cyclone is expressed as the diameter of the cylindrical section. Size of the inlet orifice- which may be circular, square, or rectangular- is expressed as a diameter, or as width and length, or as an area (in square inches). The angle of a cyclone is expressed as the total included angle. The overflow or finest classification fraction leaves the cyclone through the vortex finder. The underflow or coarsest classification fraction leaves through the apex opening.

Jan 8, 1957

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By R. W. Stormont, F. Wald

The phase diagram of the Pseudobinary section PbTe-Fe was determined. It was found to contain a monotectic and a eutectic reaction, the latter one taking place at 14 at. pct Fe and 875° * 5°C. The solid solubility of iron in PbTe was found to be 0.3 at. pct by electronmicroProbe analysis. No solubility of PbTe was detected in iron. Slight deviations from true pseudobinary behavior were found to occur in the range of - 5 to 10 at. pct Fe. In the course of a general investigation of reactions of various metals with lead and tin telluride,' the lead telluride-iron system was reinvestigated. It had been established much earlier than iron does not chemically react with lead telluride but forms a eutectic with a melting point of 879" The eutectic composition or other related information has never been reported, but for a number of years iron has been in general use for contacting of lead telluride and lead telluride alloys for thermoelectric applications. It seems therefore desirable to clarify the exact constitution of the system to furnish a base for the long-term evaluation of bonds made between lead telluride and iron either by pressure contacting or by brazing methods. I) EXPERIMENTAL METHODS Lead telluride-iron alloys were prepared in 10-g charges, using premelted lead telluride. This material was prepared from high-purity, semiconductor-grade lead and tellurium obtained from the American Smelting and Refining Co. and described as 99.999 pct pure. The iron used was "Armco" iron; the major impurities found here were 0.02 pct C, 0.018 pct Si, and 0.015 pct Cr. All remaining impurities were less than 0.01, the total of all impurities not exceeding 0.15 pct. Charges were prepared in closed quartz arnpoules which were evacuated and in some cases backfilled with high-purity argon to retard excessive lead telluride evaporation and deposition in slightly cooler parts of the ampoule. For high iron concentrations, this can lead to total separation of the constituents, since the vapor pressure and the sublimation rate of PbTe are quite high.4 Nevertheless, since the ampoules are closed, no change in overall composition was expected and the nominal composition of all alloys was assumed to be retained. X-ray diffraction analysis, thermal analysis, and microsections were used in the evaluation of the alloys. The nature of the system was such that X-ray diffraction was not particularly helpful. It merely served to establish that at all concentrations PbTe and a! iron were in equilibrium at room temperature. Thermal analysis was carried out by taking direct temperature vs time curves on a Sargent recorder where a width of 10 in. was kept as 1 or 0.5 mv by use of an automatic bucking voltage network. Quartz ampoules with minimized dead space, coated with boron nitride and fitted with a thermocouple reentrant, were used as containers for the charge. At high temperatures and over long periods of time, boron nitride reacts with iron. For the thermal analysis runs, however, this was not significant. More significant was the fact that the vapor pressure of PbTe at some of the meas -uring temperatures apparently exceeded I atrn quite considerably. This, in some cases, caused the slightly softened quartz tubes to blow out if great care was not taken to contain them and minimize time and temperatures used. As containers pure nickel tubes were used which also served to avoid temperature gradients in the quartz ampoule. Nevertheless, the experimental difficulties at high temperatures were severe and the monotectic temperature could therefore not be determined accurately. In general, the accuracy reached by the thermal analysis setup in this case is *4"C as determined with gold, silver, and tin, under the conditions of analysis here. Inherently, the apparatus is capable of reaching accuracies better than i 1°C. Also, difficulties were encountered in microsection-ing. They were related to polishing, since it is rather difficult to avoid pulling the iron out of the weak and brittle lead telluride matrix. It proved best to follow a procedure where, after grinding to 600 grit on carborundum paper, a polish with 6 p diamond was used on nylon cloth. Finally, #3 "Buehler" alumina and an automatic polisher were used for -5 min only, to avoid relief. The best etching results were achieved with

Jan 1, 1969

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By Waldemar Lindgren

During the last 15 years much attention has been given to the " contact-metamorphic" ore deposits which mainly occur in limestone close to intrusive contacts. In general, these deposits are characterized by the association of magnetite and simple sulphides with the so-called L'contact-metamorphic" silicates. These silicates comprise garnet, epidote, vesuvianite, tremolite, wollastonite, diopside, hedenbergite, ilvaite, and many other rarer forms. The contact-metamorphic zones contain also in places minerals with boron, fluorine, and chlorine, like axinite, tourmaline, danburite, fluorite, and scapolite. There is also more or less quartz and coarsely recrystallized calcite. The simple sulphides embrace pyrite, pyrrhotite, chalcopyrite, galena, zincblende, more rarely arsenopyrite. On the whole, sulphantimonides and sulph-arsenides are rare. Deposits of magnetite or chalcopyrite or of both are most common. The deposits have an irregular or rudely tabular form, following main contacts, dike contacts, or stratification planes; they rarely extend for more than 1,500 or 2,000 ft. from the contact; far more commonly they only reach a distance of a few hundred feet from that surface. The deposits are usually formed by replacement of limestone, or allied calcareous rock. Apparently they are found both in relatively pure and in impure carbonate rock. The deposits are geoiogical bodies of a chemical and mineralogical character differing greatly from the adjoining intrusive rock and from the unaltered limestone. They are rich in silica and iron, with more or less of lime, magnesia, alumina, sulphur, and rarer metals like copper. The so-called contact-metamorphic silicates which form the gangue usually are coextensive with the metallic minerals, though of course not necessarily with the merchantable ore. All opinions agree in holding the deposits of epigenetic origin, later than the inclosing limestone. Regarding the origin of the metals and the genesis of the ores there are several opinions. 1. There are those who see in these deposits the result of concentration of material contained in the intrusive rocks by means of hot circulating

Jan 1, 1915

By Robert M. Lewis

Can wet-ground mica be produced from mica schist ores, and if so, would its properties be comparable with products now on the market? This was the problem which prompted the development of a flowsheet for the beneficiation of mica schist. The fine-ground mica industry relies on weathered pegmatites and alaskite ores as sources of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and bulk-density specifications. Mica obtained from mica schist is iron-stained and decrepitated and requires additional beneficiation to produce a wet-ground mica product. Despite these adversities, there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores is considerably higher than that of the pegmatites and alaskite ores now being mined, often containing in excess of 40% mica. This higher-grade mica feed should promote a lower mining and milling cost. The mica schist ores with their higher mica content would mean less tailings to handle; however, there would have to be a means for disposing of acid and sulfate wastes. A flowsheet was developed whereby mica could be recovered from mica schist ores and beneficiated in a way that would result in a high-quality end product.' The essential phase of the process involves using reducing reagents to increase the magnetic susceptibility of iron contaminants which then can be removed with a magnetic separator. General Treatment Procedure The mica is floated by either of two methods, an amine float in an acid circuit' or the U.S. Bureau of Mines (USBM) amine-fatty acid float in an alkaline circuit' The flotation mica is ground in a pebble mill to liberate contaminated particles and expose iron-stained surfaces. The concentrate is then conditioned with a reducing reagent and passed through a Frantz Ferrofilter for the removal of magnetic material. The nonmagnetic product is acid-leached to further reduce the iron contamination. The leached material is then ground to product size and checked for specifications. Discussion of Flowsheet and Its Development Flotation: The mica is concentrated by flotation using either of two methods: an amine float in an acid circuit, or the USBM amine-fatty acid float in an alkaline circuit.' The writer does not wish to elaborate on the relative merits of the two flotation procedures; however, after investigating ores from various localities, it was felt that the amine float in an acid circuit was more consistent when using a standard procedure. Iron Reduction and Magnetic Separation: This phase of the flowsheet may be considered the key to the process. It was developed when it became apparent that hot acid leaching had just about reached its maximum effective¬ness for color improvement. S. C. Sun and William Hirsh in "Hydrochloric Acid Leaching of Iron From Pennsylvania Aluminous Clays,"` reported iron extraction for -20-mesh minerals of 82.20% for hematite and only 33.46% for magnetite. The test procedure employs a 19% hydrochloric acid solution, 104°C temperature, and 10% solids. It was felt that magnetic removal of some of the iron contaminants before leaching therefore would be advantageous. Since the iron minerals present as contaminants vary in magnetic susceptibility, it was decided to experiment with reducing reagents as a means of influencing their magnetic properties. Zinc hydrosulfite or sodium hydrosulfite were the reagents used throughout the tests. The procedure developed consists of conditioning the mica concentrate in a closed container at approximately 5% solids with a reducing reagent. Approximately 10.0 lb of zinc hydrosulfite per ton of mica concentrate is used. The ferric iron is reduced to the ferrous state (magnetic) and oxidation is retarded by isolation from the atmosphere in a closed container. After the desired conditioning time has elapsed, the material is passed through a Frantz Ferrofilter where the magnetic particles are retained and discarded as

Jan 1, 1972

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By G. Reinberg, C. D. Clarke

Most underground mining operations are dependent on pumping installations to keep the mine unwatered. The reliability of such installations is obviously of paramount importance. The volume of water to be handled is often considerable, and the total head is relatively high. In these cases, both capital cost and operating expense of the pumping installations will become significant factors in overall mining costs. To insure reliability and to keep efficiencies, and hence operating costs, within acceptable limits it goes without saying that mechanical maintenance of a mine pumping installation must receive scrupulous attention at all times. Large mine pumping installations today almost invariably use multistage centrifugal pumps, since positive-displacement units would not be economically competitive except under very unusual conditions of small volume combined with extremely high heads. Centrifugal pump maintenance, under ideal circumstances, would be confined to parts subject to normal running water, i.e., bearing surfaces, stuffing box packing, and shaft sleeves. Under adverse conditions, however, metal may be lost from the wetted surfaces of a pump by erosive or corrosive action of the pumped fluid, and maintenance costs can easily attain enormous proportions.

Aug 1, 1956

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks' and to the precipitation of second phase particles,2'3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these '(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970

By Francis Peabody

THIS paper will not be a technical paper, because, although I have been in. the business of mining and selling coal for 30 odd years, I am neither a mining engineer nor a practical miner. If I digress from time to time from my thesis, I must be forgiven by the expert engineers and highly technical gentlemen for whose proceedings this article is written. Waste of the wonderful store of power that the Creator placed at our disposal appears to have been the theory and the basis of our methods of extracting this power-waste from the time the coal is mined to the time it is consumed. Let us consider the prime causes of this wastage which has been the heritage of the coal mining industry. In the early days-about 150 years after "Stone Cole" was discovered in Illinois by Joliet and Marquette, and Father Hennepin noted a, "sole" mine on his map-the mode of mining prevalent among farmer land-owners, on whose property coal was discovered near the surface or outcropping on the hillsides, was to enter the seam by a shallow shaft or drift into the hillside and remove the coal by wedging it down until a large room was left. The roof without support would fall and our primitive coal operator would then sink another shaft or drive another drift. In these early operations only the large lumps were taken and all small pieces and screenings were left to be covered by the fall of the roof-in fact this condition prevailed in Illinois up to about 1885. Gradually the method of mining changed from the open chamber, to a single entry with rooms turned to the right and left. Later, as the demand for coal increased and the necessity for larger mines became evident, the "room and pillar" system grew to be regular practice.

Jan 5, 1917

By I. N. Zavarine

AUSTENITE is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic trans-formation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state.

Jan 1, 1934

FROM the first to the last meeting of t h e Rocky Mountain Club John Hays Hammond served as president. He guided its deliberations when there were any, but that always y o u n g organization was never particularly deliberate. Youth never is. And the Club was the embodiment of the youthful spirit of the West, which considers any- thing can be done if there be but the will to do it. Ham- mond and the others came out of the West, but they, brought the West with them P and in all the far countries in which he has served his profession and in all the honorable offices in which he has served his country, he lived true to the ideals under which he was raised. A Californian, born in San Francisco in 1855, the son of an army officer, Major Richard Pindell Hammond, educated in the public schools of his native city, at Yale, and at Freiburg, he turned early and quickly to mining. He served his apprenticeship as all successful mining men do, as assayer, surveyor, as assistant in ex-aminations and later as principal, and finally as mine manager. Even in those days of beginnings, his future world-wide career was foreshadowed in that Mexico as well as California served as his training school. His first major step up the ladder was in connection with the Bunker Hill and Sullivan mine, where he served in various positions finishing as president and considerable owner. It was from this great lead mine that he was called to South Africa, where he remained a number of years and was the technical expert who guided the great enterprises of Barnato Brothers and Cecil Rhodes. The story of his activity in developing the "deeps" of the Rand and in opening Rhodesia has been often told but is always an alluring one of adventure and accomplish-ment. After his famous escape from death at Johannes-burg as a member of the Reform Committee, he went first to London and later returned to the United States representing both British and American capital in the purchase and development of great mines in all parts of the world. For some years he was general man-ager, consulting engineer, and director of the Guggen-heim Exploration Co., but of recent years he has oper-ated entirely on his own account and with marked success.

Jan 4, 1928