Search Documents

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By D. O. Wyble, L. O. Bacon

THERE has been considerable speculation among mining geologists and mining men in general as to the relative merits of gravity methods in iron-ore exploration. Most of the investigations which have been carried out in recent years have been done by mining companies, and few if any of the results have been published. Three gravity surveys have been made in the Iron River-Crystal Falls area,' " one by the U. S. Bureau of Mines, with inconclusive results, and the other two by Radar Exploration Co. for the Cleveland-Cliffs and the M. A. Hanna companies, with results not known to the writers. Both the last-mentioned surveys were detailed investigations, the stations being spaced as close as 10 ft along traverses,' and were made to determine the feasibility of locating iron ore by gravitational methods. Because of the presence of a large body of ore already extensively drilled, Dr. Harold L. James of the U. S. Geological Survey, Iron River, Mich., suggested that a further test of gravitational methods of exploration be made in the Round Lake area of Iron County, see Figs. 1 and 2. This survey indicated a considerable regional gradient and led to a study of the surrounding gravity field and its relation to the major structural features of the syncline within which the iron formation lies. The southwestern part of Iron County presents a series of hills and hollows elongated in a roughly north-south direction. The bedrock topography is of pre-glacial origin. Relief is moderate; a maximum elevation difference of approximately 350 ft was observed during the survey. Major drainage is dendritic with the larger streams: the Brule to the south, the Paint to the north, and the Iron in the central part. Hills are thickly grown with hard- woods, and lowland areas, not under cultivation, are usually covered by second-growth softwoods. The area covered in this paper includes the southern half of Iron County, Mich., with a deep synclinal basin occupying the central part of the area, and the southeast corner of Gogebic County, immediately to the west of Iron County. The upper Huronian iron formation, slates, and graywackes which form the synclinal basin rest upon a greenstone basement. The basin has not been completely outlined by exposures, drill records or other means, as outcrops are scarce and the thick mantle of glacial drift makes geological investigations extremely difficult. Glacial drift varies in depth up to 300 ft or more. The drift is usually thickest under the hills and is thinnest in the depressions and along drainage courses where most of the bedrock exposures occur. The area over which gravity investigations were made is almost, entirely covered by glacial material. Bedrock of the basin consists of a complexly folded series of iron formation, slates, and graywackes. One of the series of slates has a high magnetic susceptibility due to the fine-grained magnetite it contains. This formation can be detected readily. by magnetic methods and provides a marker horizon which can be easily followed. The magnetic slates are stratigraphically above the iron formation, and much of the geological interpretation of the area is based upon the magnetic anomalies they produce.

Jan 1, 1953

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By J. R. Lewis, J. H. Hamilton, V. D. Hanson, K. W. Heinlein, J. M.194-000-000-006 Vonfeld, J. P. Denny

TWO overfeed drum-type separators using a suspension of magnetite in water as the separating medium have been installed in the Champion NO. 1 preparation plant of the Pittsburgh Coal Co., Division of the Pittsburgh Consolidation Coal Company. A simplified flow diagram of the Champion No. 1 coarse coal circuit is shown in Fig. 1. A railroad car rotary dump, capable of handling 20 cars per hr, discharges the coal into a hopper. Coal is fed from the hopper of the rotary dump to a 60-in. belt conveyor by two reciprocating pan-type feeders. The belt conveyor feeds the run of mine coal onto the main raw coal screen. The first deck is fitted with 3 in. round hole perforated plate which removes the 3x0-in. coal. The second deck of the screen is equipped with 6-in. lip screens which separate the remaining coal into +6 in. and 6x3 in. The +6 in. coal is transferred to a shaking picking table and then discharged onto the loading boom. The 6x3-in. coal is fed to the No. 2 dense medium vessel for cleaning. The clean coal from this unit flows to a vibrating screen where the medium is removed and the coal sized into 6x4 in. and 4x3 in. The 6x4-in. coal is transferred to the loading booms and the 4x3-in. is conveyed to the clean coal classifying screens to remove degradation. The 3x0-in. raw coal is blended in a system composed of three storage bins having a total capacity of 400 tons. From these bins the coal is fed onto a 48-in. flight conveyor by three reciprocating feeders. This flight conveyor delivers the coal to the Rheo plant. The 3x0-in. coal is then cleaned in two 48-in. Rheolaveur launders each equipped with two Rheo boxes. The first set of boxes removes a primary refuse and the second set produces a middling product which is recirculated in the launders. The cleaned coal and water overflows from the primary launders to two sizing and dewatering shaker screens where the water and — -in. coal are removed for further cleaning in the Rheo fine coal plant. The 3x3h-in. clean coal is combined with the 4x3-in. coal from the No. 2 vessel, sized into 4x2 in., 2x1 34 in., and 1'/4x in., then sent to the loading booms. The 3x0-in. refuse from the primary launders is normally fed to the No. 1 dense medium circuit, but any portion or all of this material can, as an alternate, be processed in the Rheo rewash launder. The primary refuse when fed to the dense medium circuit is screened into YSXO which is cleaned in the fine coal plant and 3x for cleaning in the No. 1 vessel. The clean coal from this vessel is passed over a vibrating drainage and rinse screen, then sluiced to the rewash sizing shaker where it is dewatered and sized for loading. The installation of a pilot plant separating vessel using a suspension of magnetite in water was pro-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Adam L. Wesner, A. C. Richardson

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. DURING World War I1 the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pct iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pct of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals Were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The —10 +35 mesh fraction was found to be the most promising feed for producing the low-ash content coal. A batch of 30 tons of — --in. coal was screened at 10 and 35 mesh; the yield of —10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the —35 +48 mesh range. A representative portion of the —10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pct ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1953

By Adrian E. Ross

Diamond drilling through caving formations at depths greater than ZOO0 ft has long presented serious difficulty, generally solved either by casing or cementing. Casing is permitted only when the resulting smaller hole is acceptable, and cementing is frequently a problem at depth. A new method that injects cement under pressure at the desired location is an aid in diamond drilling deep holes. DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pump- ing process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1953

Jan 1, 1953

Jan 1, 1953

Jan 1, 1944

By David P. Hale

The Cartersville barite district is near Cartersville, Ga., in the southeastern part of Bartow County, about 43 miles northeast of Atlanta. The area over which active mining is being done extends about six miles in a northeasterly direction and is about three miles wide. Barite production in Georgia began about 1907,' but the existence of the mineral was known much earlier. At present four companies are operating washing plants and three other plants are operating on leases from those companies. The chief impurities in the ores are silica and iron oxide. The silica is easily washed and jigged out and gives little trouble. Any gravity separation between the iron and the barite is generally poor, owing to the slight difference in specific gravity. Two operators have turned to magnetic separation as the solution to the problem and have made remarkable improvements in the finished product. By very close sizing prior to jigging, the separation between iron and barite has been greatly improved. In some localities manganese occasionally appears as an impurity, but is fairly easy to eliminate by gravity methods. A considerable percentage of iron and silica is eliminated by being broken free in crushing. Until methods for the recovery of fine ore were introduced a minimum of crushing was done, but modern methods allow more than formerly. The depression years brought about the need for increased recovery of ore handled on the part of the producers and a demand for a higher grade of product on the part of the buyers. Improvements in milling and mining practice have had a far greater effect, however, than merely the production of a better grade of ore with greater recovery. They have opened for mining large areas that a few years ago were considered noncommercial deposits because of their inaccessibility and their high iron content. It is no exaggeration to say that the new methods have more than doubled present known reserves of barite ore of economic value.

Jan 1, 1942

By E. C. Houston, R. A. Laurence, F. A. W. Davis, L. L. McMurray, H. S. Rankin

This paper is coodensed from several reports by members of the staff of the Minerals Testing Laboratory of the Tennessee Valley Authority, on a series of experimental tests in the beneficiation of barite of the Valley area. These experiments were conducted upon a large number of samples taken from several mines in three different districts. The area contains numerous producing deposits, nearly all of which are hampered by the high iron and silica content of the ores. Because of the small difference in specific gravity between the iron oxide and the barite, a gravity separation is generally poor. The removal of the iron thus offers a special problem. Some of the operators have turned to magnetic separation to meet the shipping requirements for less than one per cent iron. The present experiments were conducted to determine the application of decrepitation or flotation in simplifying the concentration of the barite by removing the iron oxide and silica in one operation. Practically all the barite marketed in the area has been as "off-color" crude. The bleaching studies were made to determine the bleach-ability of the ores to alleviate this inferior grading, placing them on the market as bleached barite. Geology Barite has been produced at many places in the Tennessee Valley area, and prospects and minor deposits are known at many other places, but practically all the production of barite in the Valley has been from the Sweetwater district of East Tennessee. Other leading areas of former production are the Tazewell-Russell counties areas of southwest Virginia, the Del Rio-Stackhouse district of East Tennessee and western North Carolina, and the Fall Branch district of upper East Tennessee. The areas described in this paper are those from which samples used in the concentration tests were obtained.

Jan 1, 1942

By G. W. Jarman

The purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electrostatic separators and air flotation or air tables. Magnetic Sepaeatohs In general, separation is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 080, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1942

By F. Cadena

Hiwassee Darn, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are present in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about ¼ in. maximum size, although the bulk of the deposit is medium grain. Extensive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chickamauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrangement of equipment if the optimum in flexibility and capacity is to be attained. Flowsheet Rock is ioaded by 3-yd. electric shovels into 12-yd. dump trucks, which carry the rock to the primary crusher, a 42-in. Superior McCully gyratory unit set at 4¾ in. (Fig. 1). The primary crusher discharges directly onto a 42-in. inclined belt conveyor, which carries the product to a surge storage pile with a maximum live storage capacity of approximately 3000 tons. A concrete tunnel under this storage pile houses the feed end of a 36-in. belt conveyor (conveyor B) fed by a 36 by 66-in.

Jan 1, 1942

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.' The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898' C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By James Norman, E. W. Gieseke

Spodumene is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components. The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li²O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston,S the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. Study of Method of Flotation Separation Most of the work on concentration of spodumene was done with rock from near King's Mountain, North Carolina. Rock from two

Jan 1, 1942

By James Norman, Oliver C. Ralston

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by Froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each or clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1942

By James Norman, Benjamin S. Lindsey

BaritE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the 'more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, II.II per cent SiO², and 2.85 per cent R²O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of non-metallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is scparated. Laboratory Flotation Work Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1942