Search Documents

By M. Karfakis, K. Kim, R. V. de la Cruz

The in situ deformability of a closely jointed basalt rock mass was determined by two different methods: the NX-borehole jack method where displacements of opposing curved platens were related to applied hydraulic pressures, and the modified Goodman jack method where tangential strains on the borehole walls were related to induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX-borehole jack method. To explain the discrepancy, the influence of fractures and test variables, such as depth, orientation, hole location, and applied pressure on the calculated modulus of the rock mass, were analyzed by factorial analysis. It was found that the orientations and measurement depths have statistically significant effects. The in situ deformability values obtained by nonlinear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1984

By A. A. Schweizer

A method to improve the quality of Magmont zinc concentrates to become acceptable feed to an electrolytic zinc refinery is described. The magnesia content of zinc concentrates produced was too high due to particle locking with sphalerite in coarse fractions. Regrinding the concentrates to a very fine particle size and then refloating the sphalerite was chosen to eliminate a sufficient amount of the magnesia to make the concentrates acceptable.

Jan 1, 1984

By M. A. Meyers, P. P. Meyers

The analysis of the phenomena involved in determining the compressive strength of iron-ore agglomerates leads to the identification of important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compressive axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments u due to internal voids of varying sixes that act as stress-concentration sites. Two novel testing procedures are proposed. The first consults of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents vacant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1984

By B. C. Johnson, K. L. Sublette, F. L. Prestridge

A problem common to the petroleum and mining industries is the resolution into its component phases of mixtures composed of a polar liquid dispersed in an immiscible, continuous nonpolar liquid. In the petroleum industry the polar liquid is water or brine and the nonpolar liquid is crude oil. The source of the entrained aqueous phase is connate water and/or condensed steam used in secondary and tertiary recovery methods. In the mining industry dispersions of polar liquids in immiscible, nonpolar liquids are created in solvent extraction (SX) systems. In these systems the polar, dispersed liquid is leachate or stripping solution while the nonpolar, continuous liquid is the extraction solvent.

Jan 1, 1984

By E. C. Simmons

Uranium is an incompatible element with respect to the major rock-forming minerals crystallizing from granitic magma, entering instead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late-stage fluids that can form ore deposits directly, or labile U that can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U-enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite mine area, Washington, have geochemical characteristics that fit the model presented very well. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1984

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should coder handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1984

By L. C. Binon

Exploration budgets are commonly determined by rules of thumb, such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve company goals. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1984

By R. N. Schulz

The recently completed modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located microprocessor based control system connected to a central control room. Operation of each micro-processors can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1984

By M. A. Schimmelpfennig, A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to longer travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation may be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways may contribute to formation. This study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Co. to identify causes of the problem.

Jan 1, 1984

By R. G. Hite, R. G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mechanics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1984

By David M. Cregger

The performance of the nation's first geologic repository for Commercial High Level Waste will be evaluated in a variety of ways which will involve the use of the state-of-the-art thermomechanical computer codes. Elastic properties of the host rock and the materials surrounding the repository are required for this numerical modeling effort to assess both near- and far-field effects. Only limited laboratory testing is possible, however, making it extremely beneficial to expand the data base by calculating dynamic elastic properties from available geophysical well logs. Elastic theory dictates that for an isotropic solid there are only two independent variables in addition to mass density, namely the compressional velocity, the shear velocity, and Poisson's Ratio. Compressional velocity and density are readily measured by geophysical well logs or in the lab; the crux of the solution requires measuring or determining either the shear velocity or Poisson's Ratio. Examination of acoustic propagated shear waves measured during confined compression testing demonstrates that Poisson's Ratio is a fundamental lithology-dependent parameter. Once a rock mass is appropriately classified, application of the laboratory derived dynamic Poisson's Ratio will yield a continuous and reasonable in situ modulus from acoustic and density logs. For preliminary characterization and assessment of the mechanical properties of rocks within the subsurface, and for studies of rock quality, this method is sufficiently accurate. The general availability of acoustic and density logs from wells logged for other purposes has made the application of this method desirable.

Jan 1, 1984

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff" backfill to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By George W. Toth

This paper describes the features of a computer cost model developed to estimate requirements and costs of individual coal mining projects. Detailed cost analysis procedures for both coal mining and preparation are incorporated into the model. This model has been developed over a period of seven years through funding provided by the Electric Power Research Institute (EPRI). The model follows a process engineering approach for the estimation of all project capital and operating costs. A discounted cash flow analysis procedure is also designed into the model to allow for the solution of cost/ton or cost/MMBtu of clean coal production. The model can be applied to most surface or underground mining deposits and can accommodate a wide variety of coal washing situations. This flexibility makes the model a particularly useful tool for preliminary project analysis, property screening, investment analysis, mining technology assessment, coal cleaning level assessment, and general property valuation.

Jan 1, 1983

By P. R. Sheorey

Understanding of in situ rock mass behaviour has taken a step forward with the advent of the refined rock mass classifications of Wickham, Bieniawski and Barton et al. In this paper six case studies are given in brief showing how Barton's classification could be used in mining situations. The cases cover stability of roadway junctions under shallow covers, support pressure estimation in roadways in intact and failed rock conditions, determination of the safe unsupported span of a wide stope and estimating the stability of roadways in two contiguous seams standing 011 small pillars against puncture of the parting rock.

Jan 1, 1983

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and (2) cover the various aspects of the major raw materials used to make glass. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks used in glassmaking, the reader is referred to chapters in the commodity section of this book. Glass Industry Statistics Glass manufacture in the United States can be divided into three major product classifications as follows: 1) Glass containers 2) Pressed and blown glass 3) Flat glass Glass containers include bottles and jars for the packaging of food and beverages, as well as drugs, chemicals, and cosmetics. Pressed and blown glass includes table, kitchen, art and novelty ware, lighting and electronic glassware, and fiber glass. Flat glass covers sheet or window glass, plate, laminated, and safety glass. The US Department of Commerce statistics, as recorded in the 1977 Census of Manufacturers, compares the dollar value of glass shipments for each product category. These statistics are shown in Table 1 (Anon., 1980) and are self-explanatory. A comparison of the tonnage output in each product classification is difficult, as production data is reported in "gross" for glass containers, "pounds" for fiber glass, "pieces" for glassware, [ ] and "square feet" for flat glass. In the case of glass containers, an average "pounds per gross" factor can be applied to the total production figures reported in thousands of gross in Bureau of Census industrial reports. Table 2 presents the calculated annual production tonnage for glass containers for the years 1974-1979. Except for 1979, there was a yearly increase in production. The tonnage figures of Table 2 are further influenced by decreasing weight per gross which has occurred in the glass container industry since 1975. This reflects the gradual shift to lighter weight containers for beverages. Other segments of the glass industry have experienced growth, but the figures in tons are not published information. Fiber glass growth has been influenced by the heavy demand for insulation as part of energy conservation efforts on a national basis. The production of flat glass by the float process has continued to grow with several new plants entering production. All portions of the glass industry experienced the effects of the general economic decline of 1979-1980, but the outlook for the future is bright. Batch Materials For Glass Use Materials and Function Soda-lime-silica glass represents the largest proportion of glass manufactured for commercial use. It is produced by the fluxing and

Jan 1, 1983

By W. J. Nelson, R. B. Nance

Detailed underground geologic mapping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Co., which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium -to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular- bedded limestone, and (4) fine-pined, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sandstone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults and limestone "bosses." Less stable roof and wet conditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that intersect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural pattern apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof supports. Drilling also is useful in locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1983

By John T. Grasso

This paper describes the computer-assisted development and implementation of new written examinations for persons desiring to become certified as underground or surface mine electricians in the State of West Virginia under the certification program defined by the WV Department of Mines and the Board of Miner Training, Education and Certification. The procedures used to develop and validate the new certification tests have simplified the administration of the new tests. Future developments in mine electrical work can also be easily incorporated into the certification program by augmenting the existing computerized pool of test questions prior to computer-production of future test forms. Most important, computerization now facilitates continual evaluation of the certification program, to contribute to greater safety in mine electrical work in West Virginia.

Jan 1, 1983

By Michael J. Bailey, Peter M. Douglass

INTRODUCTION Spoil pile slope failures can have costly consequences. In- stability in the form of a single major event or as a recurring problem can 'mean lost production, lost resources and damaged mining equipment. In extreme but not uncomnon cases, a major spoils slide can force the closure and abandonment of a pit. Slope stability is affected by mine operating practices as we1 l as geologic conditions and material parameters. Mine operators can enhance spoil pile stability through constructive changes in their operations. Attention to the causes of in- stability can lead to development of operating practices tailored to site specific problems. Action aimed at limiting future instability is frequently more cost effective than continually "coping" with unstable spoils. The effect of mine operations on material properties is often overlooked because the "data" are not easily quantified nor input directly into stability analysis equations. We have found, however, that miners' experience with their own operation, as well as data pooled from similar operations, yields relation- ships which can be utilized to solve stability problems. The repetitive nature of area type surface coal mines with successive spoil pile rows further enables the development of useful site specific relationships. Stability problems can be mitigated by applying these relationships.

Jan 1, 1983

By Michael Richings

Although the role of slope stability has not changed, there have been changes in the mining industry which affect the geotechnician engaged in slope stability studies. The deposits currently being mined or evaluated are technically difficult , capital intensive, and economically marginal. In addition, many mining companies are now either controlled by oil companies or are financing projects through bank loans. The mining investor or decision maker is, therefore, often more sophisticated financially, but less sophisticated in mining terms. The impact of these changes will be to force the geo- technician and mining engineer to attempt to quantify risk and financial implications of a slope design. In conclusion, this paper outlines several questions which mining engineers should be asking those engaged in geotechnical studies and indicates the necessity for the mining engineer and geotechnician to work together and quantify the financial risk associated with a geotechnical design.

Jan 1, 1983