Search Documents

By P. L. Lavery

A numerical method to derive approximate solutions for stress intensity factors for rectilinearly anisotropic bodies without resolving to complex variable approach is presented. The method is based on the assumption that the crack opening profile can be simulated by a simple curve such as an elliptic function and a relationship is found for the stress intensity factor in terms of near tip displacements. An example solution is derived for a transversely isotropic body and the results are verified with Westergaard's stress function approach. The proposed model has a great potential for the applications to fracture mechanics of anisotropic rock materials.

Jan 1, 1984

By J. E. Schiller, S. E. Khalafalla

Due to its unique surface properties, magnesium oxide (MgO) is an excellent medium to filter asbestos and other suspended solids from water. MgO operates up to twice as long as a sand filter before backwashing is required while flow rate and filtrate clarity are as good or better with MgO.

Jan 1, 1984

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.9 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV.

Jan 1, 1984

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By W. Kane, M. Karmis

Roof and rib failures in underground coal mines are one of the major problems facing the industry today. In addition to safety considerations, the resulting economic impact of such failures is staggering. Uncovering and replacing buried and damaged equipment and clearing entries can account for a large expenditure in lost man-hours and machinery. Yet, because of the complex nature of its formation, geological variability, and structural characteristics, coal mine roof strata is one of the least controlable of all mine design parameters. This is especially true along the leading (southeastern) edge of the Appalachian coalfields where considerable faulting and movement has contributed to hazardous coal mining roof conditions. During this research, a detailed study of several mines, in the southern Appalachian coalfields, was undertaken to determine the most prominent geomechanical factors affecting roof stability and to evaluate their influence in promoting unstable ground conditions. In order to accomplish this task, the major geological and geomechanical features found to be detrimental to coal mine roof within the Appalachian basin were identified and mapped in four Virginia mines. Statistical processing by chi-square and regression analysis was used to determine the influence of geology, mine-layout, and support methods on roof stability. It was found that some easily determined parameters can be successfully used to predict potentially unstable areas. A simplified roof classification system was developed based on these geomechanical parameters, which can be used to assess the stability of a particular roof type. A roof rating index was also devised capable' of expressing the probability of a failure under a given set geomechanical condition.

Jan 1, 1984

By K. V. S. Sastry

First attempts to apply computers for the modeling, simulation and analysis of mineral processing unit operations date back to almost twenty years. Since then substantial efforts have been directed to the development of computer software for mineral processing. Current literature indicates considerable activities in the development of computer packages for interactive and batch simulation of individual unit operations and integrated plant operations. This paper presents a comprehensive review of various simulation systems that have been described in the literature along with a discussion of present trends in the development of mineral processing simulation software. Finally, the paper includes a detailed discussion of the desirable features in future simulation packages.

Jan 1, 1984

By J. R. Hillebrand

From the abstract, "A realistic ore deposition model to serve as a conceptual framework." Further, on page 246, "The first area of study was the Josephine peridotite, now identified as an ophiolite terrane, located in northern California and southwestern Oregon (Fig. 3). Here, it was felt that we could test the models shown in Figs. 1 and 2 and, if successful, expand the model and test it in other chromite districts in the US and around the world." My comments refer only to chromite deposits in Europe and the Middle East. First, I question that may chromite deposits occur in the idealized ophiolite section shown in [Fig. 1]. Second, although some podiform deposits (referring to morphology) have been important (Gulernan, Turkey, for example), the stratiform deposits are of greater importance in tonnage and frequently grade. Examples include Nada, Yugoslavia; Bulqiza, Albania; Xerolivado, Greece; Saranovsk, Russia; and Abdasht, Iran.

Jan 1, 1984

By Dr. O’Neil Thomas J., Donald W. Gentry

"We can easily represent things as we wish them to be..” -Aesop INTRODUCTION The first eight chapters of this book have primarily addressed the concepts and fundamentals associated with project valuation, particularly as they apply to mining-related projects. Specific emphasis was placed on the engineering and economic parameters and estimates necessary for quantifying line items in pro forma income statements and the subsequent calculation of net annual cash flows. Given these estimates of relative benefits, costs, and annual cash flows for a project, it then becomes necessary to convert these estimates into measures of relative desirability or attractiveness. The criteria and techniques typically utilized to determine project acceptability or desirability are, then, the topics of discussion in this chapter. Before proceeding it may be advantageous to put the problem of project evaluation into proper perspective by reiterating some of the fundamental concepts developed in Chapter 1. The basic premise set forth in this book is that the objective of the firm should be to maximize its value to its owners (stockholders' wealth). This value or wealth is represented by the market price of the firm's common stock; consequently, the primary objective of the firm can be restated as one of maximizing the value (price) of the firm's common stock in the marketplace over the long term. This price, in effect, is an indicator or index of the market's perception of the company's progress and a reflection of the investment, financing, and dividend decisions made by corporate management. These three major decisions are inter- related and jointly impact the market price of the firm's stock. Therefore, if the objective of maximizing the value of the firm to its stockholders is to be achieved, an optimal combination of the three decisions will be necessary. It is important to emphasize that maximizing stockholder wealth is not the same as profit maximization or even the maximization of earnings per share. Corporate managers making decisions based on the objectives of maximizing profits and/or earnings per share must recognize that these objectives do not consider: (I) the timing or duration of expected returns, (2) the business and financial risks of the promised earnings, or (3) the dividend policy of the firm. Obviously all of these factors are of concern to the company's stockholders and will have an effect on the market value or price of the firm's common stock. Maximizing market price per share, or wealth maximization, is therefore the appropriate corporate objective and

Jan 1, 1984

By E. B. Jensen, C. E. Doane, J. F. Pirozzoli

Results of an extensive one-year test of a nonelectric explosives detonating system led to the mine-wide adoption of this system in early 1978. Since that time, further experience with nonelectric initiation has verified the earlier results, which include the following benefits: Electrical insensitivity Improved productivity Cost effectiveness High reliability While electric blasting caps still experience a limited we restricted to trunkline initiation, all heading rounds as well as the bell, undercut, boundary-cutoff, and raise blasting are detonated nonelectrically. The primary blasting agent used at the Henderson mine is AN/FO, and primers are typically one of the following products, depending on applications: PETN, semi-gelatin dynamite, or a nonnitroglycerin water-gel slurry

Jan 1, 1984

By G. Hasenfus, M. Karmis, G. Goodman

Surf ace subsidence is rapidly becoming an important environmental consideration of active as well as abandoned mining operations. The damages attributed to this phenomenon have been witnessed in both rural and urban areas and include land settlement and fracturing, structural damages to surface buildings or facilities and disruption or contamination of ground water supplies. The problem of mining subsidence has gained considerable emphasis in the Appalachian coalfield. The increased mining activity over the past few years and the particular topographic conditions, lithologic and structural environment, mining methods and hydrological patterns are all factors which have contributed to specific subsidence characteristics in this region. The objective of this paper is to discuss and review the most widely accepted methods of subsidence prediction above longwall as well as partial extraction systems in Appalachia. These include an accurate and easy to apply empirical method, which has been developed entirely from field information pertaining to the Appalachian coalfield and incorporates both geometrical and geological information of the panel in question. The second method is a development of influence functions and is founded on the zone area approach. Both methods, originally derived for longwall mining, have been expanded to include room and pillar applications and have been widely used by the mining industry in the Appalachian coalfield.

Jan 1, 1984

By K. Unrug, G. Herget, A. Smith

SUMMARY Statistics on roof falls indicate that the cost of just removing the unwanted waste from roof falls in US coal mines amounts to about $20 M per year. Almost 40 percent of fatal accidents occur under permanently supported roofs, indicating that the assessment of roof stability is still a very difficult task. In an effort to obtain a better understanding of roof fall occurrences, rock strength and ground stresses were determined in the roof of one mine each in Western Kentucky, northern West Virginia, and Eastern Kentucky. Triaxial ground stress determinations clearly show that horizontal stresses were higher than vertical stresses, and that maximum stresses in the horizontal plane were concentrated between the NE-SW to E-W direction, with the exception of the Eastern Kentucky site which was above the drainage. Magnitudes of stress components may vary considerably in one drlll hole. Strength tests of roof strata materials were done on core samples. Mapping of roof falls showed that the geometry of an opening or maximum span were not the overruling factor because in the same general area, a roof fall was observed in a room (entry) which connected two stable four-way intersections. It should be noted that, in very wet areas, the roof can break up to the bed where water is carried, and a very low ratio between extent of roof fall to height of roof, fall is observed. Geometry is, however, a contributing factor because nearly 70 percent of roof falls are intersection falls. The frequency of fractures parallel to bedding in failed roof strata is much higher than that observed in the original strata, indicating a significant amount of working in the roof before failure.

Jan 1, 1984

By J. M. Avasthi

The DOE-funded (Contract No. DE-ACO3-77ET13108) Gulf Research & Development Co. (GR&DC) field tests of underground coal gasification in steeply dipping beds (UCG/SDB) were conducted in the North Knobs area, located 12.8 km (8 miles) west of Rawlins, WY. The site has a gently rolling, sparsely vegetated, semidesert terrain on the transition zone between a broad, flat basin (Great Divide Basin) to the west and the subdued mountains of the Rawlins uplift to the east. A comprehensive geotechnical program (Ahner et al., 1980) was essential to successfully complete the test program. Emphasis of the program was the subsurface characterization of the site and consisted of mapping, drilling and logging, core analyses, and hydrologic tests. The samples of lithologic units over- and underlying the G coal seam were tested in the laboratory for their modulus and strength. This program provided the required data necessary for designing surface facilities, input for permits, and ensuring correct placement of the process modules. The two UCG tests at the Rawlins site were conducted in the nominally 6.7 m (22 ft) thick G coal seam (rank-subbituminous B), dipping at 63°.

Jan 1, 1984

By T. Kusakawa

In Japan, natural gypsum is rarely mined for industrial use and almost all gypsum is synthetic, that is desulphogypsum, produced from waste sulphur dioxide gas from metal smelters and power plants and other industrial waste sources. The amount of synthetic gypsum production (1979) reached more than 6 Mt/a (6.6 million stpy). Major uses are for cement and building materials. Other uses include soil conditioner, investment casting molds, and organic composite materials. Sulphur recovery by gypsum decomposition is being examined. This paper summarizes present Japanese production and uses of synthetic gypsum produced from industrial wastes.

Jan 1, 1984

By Irwin Remson

Some unique hydrogeologic issues are inherent in the problems of siting, designing and licensing a mined geologic high-level nuclear waste repository. The problems involve hydrogeologically unfamiliar rocks for which little proven technology has been developed, long containment periods, elevated temperatures, and externally-imposed management constraints. In evaluating the existing national program, it should be recognized that hydrogeology is only one aspect of the total nuclear waste disposal problem, that the use of multiple barriers requires that the hydrogeologic system be considered in its entirety as a total system, and that engineering modifications can improve the isolation capabilities of certain barriers. Important research questions involve the mechanics of transport through dense fractured and unfractured rocks, methods for measuring vertical hydraulic conductivity, and a variety of geochemical questions. Current expectations for "high quality data" from either in situ or laboratory testing are unrealistic, and a modified approach to repository hydrogeology is needed. The dilemma is that the hydrogeological characteristics that make a potential host rock more satisfactory for respository siting are the same characteristics that are difficult to characterize and make the particular site more difficult to license. Finally, evaluation of the containment potential of any candidate site will become meaningful only with detailed underground exploration, mapping and testing in the host rock formations at the repository levels.

Jan 1, 1984

By G. Ferrara

In process and plant simulation, more reliable prediction of industrial results and evaluation of data for designing purposes may be attained by the combined use of (a) modeling and simulation of ore characteristics and (b) modeling and simulation of integrated plant operations. The systems for modeling and simulation of ore characteristics are discussed as well as the conditions in which their use may be necessary (complex structure of the ore-body and variability of the ore fed to the plant). Two examples, for coal and bauxite run-of-mine (ROM), are reported. The procedure of linking the process unit models and the approaches for the solution of integrated systems are indicated. A general-purpose program for the simulation of integrated plant operations is described, and some examples of its use are reported.

Jan 1, 1984

By D. A. Dahlstrom

In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in [Fig. 4]. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in [Fig. 4]. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensers, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89c/t (81c per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed.

Jan 1, 1984

By Subhash C. Malhotra

This paper discusses the historical background on major sources of obsolete electronic scrap and spent catalytic converter scrap. The paper discusses the principal changes taking place that will affect the future supply of these scraps. The author projects from this background the future opportunities for reclaimers and refiners in these two important segments of the precious metals scrap reclamation industry.

Jan 1, 1984

By Robert S. Dalzell, Ernest A. Curth

Following the introduction of shields to the U.S. longwall mining scene and the steady increase in the number of shield faces during recent years, the occurrence of longwall -ground-control -associated accidents has shown a welcome downward trend. But even though the accident experience is favorable, problems exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. Therefore, the Bureau of Mines has reviewed foreign remedial techniques to evaluate their potential for domestic application. Such technology includes cribbing, strain absorbent modules (SAM'S), inflatables, wire meshing, chemical rock stabilization, synthetic foams, and monolithic fills.

Jan 1, 1984

By Randall J. Essex

A massive mudslide blocked a river in Utah, impounding a 61 m (200 ft) deep lake. Under emergency conditions, a system was designed and constructed to: (1) drain the impounded lake; and (2) provide a permanent diversion for the river around the mudslide. The system consisted of a low level tunnel, a connecting vertical shaft daylighting close to the lake shore, control valves mounted within the tunnel, and an inlet channel between the lake and the shaft. This paper focuses on the problems and concerns surrounding the inlet channel excavation and the stabilization of the remaining vertical rock walls.

Jan 1, 1984

By S. Webster, M. Karmis, C. Haycocks

Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to the recovery, cost and safety of mining the subsequent seams. This paper describes the ground control mechanisms involved in mining through a passive subsided zone or all actively subsiding trough. Data were extracted from case studies, primarily from the Appalachia region, for construction of empirical models to predict interaction problems that can occur in overlying seams. Inner-burden thickness, innerburden lithology, percentage extraction, lower seam height, time and overburden were analyzed to determine their effect on upper seam damage. Magnitude of upper seam subsidence was incorporated, together with a broad classification of rock types, to predict the type and range of damage that can occur in the upper seam. Results are summarized in graphically and nomogram form for use in. engineering design.

Jan 1, 1984