Search Documents

By D. L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry. It presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a US Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) uses the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package uses a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgment scheme that provides an effective method of identifying problem areas that may exist in the mine network. The package was written in Fortran for a 64-kilobyte, Z80-based microprocessor computer.

Jan 1, 1986

By D. L. Passmore, J. D. Bennett

The degree of injury and days lost from work due to an injury are examined for selected electrical sources, occurring in conjunction with falls of the injured miner or with selected machinery, that could have been eliminated by use of diesel equipment. Although the number of preventable electrical source injuries is small relative to the total number of injuries during the period examined, many lost-time injuries could have been precluded and thousands of days lost from work could have been avoided.

Jan 1, 1986

By A. K. Gangopadhyay, J. J. Moore

The effect of grinding media composition, mineral type, and slurry environment on the wear rate of various grinding media (balls) are discussed. Sufficient wear data have been obtained and correlated. Modes of wear were determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1986

A. Cook K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed. Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. [ ] Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing. ?

Jan 1, 1986

By B. K. Parekh, W. M. Goldberger

Silicon carbide (Sic), produced by heating rice hulls to elevated temperatures, contains a mixture of beta crystalline silicon carbide whiskers, particles, and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 microns in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean, high grade SiC whisker product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90%. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1986

By R. C. Rastogi, F. F. Aplan

The goal of this study is to evaluate the coal flotation process and the interaction of the chemical (reagent) and hydrodynamic (machine, operational) variables as they affect yield, flotation of various sized particles, and sulfur and ash rejection. Coal flotation is found to follow a first order process with the coal floating much faster than either pyrite or ash. This circumstance may be used to achieve gangue rejection during flotation. When floated with MZBC, cresol, or pine oil frothers, coal floats in the size sequence: 108 pm ( - 65 mesh), 589 x 808 pm (88 x 65 mesh), and 1.17 mm x: 589 pm (14 x 18 mesh). However with a substantial amount of fuel oil collector, all particles tend to float roughly in proportion to their content in the feed. An increasing aeration rate was found to be the most important variable in increasing the coal flotation rate. This increase in flotation rate, unfortunately, is also accompanied by an increase in the flotation rate of the pyrite. The rejection of pyrite during coal flotation is best accomplished at low aeration rates, low frother concentrations, and low impeller speeds.

Jan 1, 1986

By K. Hanumantha Rao, A. Nayak, . K. S. Narasimhan, S. N. Mahapatra

Selective flocculation studies carried out with iron ore tailings generated at Kudremukh iron ore plant indicate that a concentrate containing 63% iron can be obtained from the tailings containing 34% iron with around 60% recovery. This opens up the possibility of recovering most of the iron lost in the tailings generated at 2 kt/h (2200 stph) while processing 22 Mt (24 million st) ore per year. This would mean that the productivity could increase by around 50%. In these studies, it has been established that caustic degraded tapioca starch is a most effective agent for selective flocculation. While potato starch after caustic degradation can also be used, neither the parent starch nor the amylopectin compound is as effective.

Jan 1, 1986

By F. S. Knoll

The expanding role of electrostatics as applied to minerals and related fields is covered in this paper. New and existing forms of electrostatic separation are classified into two broad groups: separation of charged particles and separation of neutral particles. The basis for each form of separation is discussed along with particle examples and results obtained.

Jan 1, 1986

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

By J. B. Gwiazda

This work contains a description of a new design of lemniscate-guided powered roof support units, with a discussion of currently designed supports and their interaction with the roof. Conventional roof supports of this type present a serious reaction with the roof because of the horizontal displacement of the canopy in the course of decreasing support height as the support takes weight. The new design presented eliminates previous disadvantages of lemniscate supports and ensures proper performance of the latter in relation to the roof of a mine working.

Jan 1, 1986

By A. K. Sinha, K. M. Sinha

Several studies concluded by various agencies (Coal Outlook, 1982; Malhotra, 1977) indicate that both the national and international markets for utility coal, which have been growing in recent years due to the uncertainties in petroleum supplies, will continue to grow in the foreseeable future. The areas where the Gemand for utility coal is projected to increase sub- stantially lie close to the midwestern coal fields, in the southeastern US, and in western Europe. Illinois has all the elements necessary to become an important exporter of thermal coal (Library of Con- gress, 1981) provided the coal is desulfurized to meet the environmental restrictions. Because of its high energy content, Illinois Basin coal, if desulfurized, has great potential for competing in the utility markets both nationally and internationally. Sulfur in coal occurs in organic and inorganic forms. The inorganic sulfur in Illinois coal is almost exclusively pyrite. The pyrite can be liberated by grinding and removed from the coal by such techniques as froth flotation. The Illinois Basin coals reportedly contain (Gluskoter and Simon, 1968) an average of 3.57% sulfur. Out of this, 2.06% is pyritic, 0.08% is sulfate, and 1.46% is organic sulfur.

Jan 1, 1986

By A. Rakshit, W. E. Kolb, Y. C. Kim

An IBM/XT microcomputer with 10 MB hard disk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this automatic truck dispatching system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites, and three material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the system is fully operational on a realtime mode.

Jan 1, 1986

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By S. E. Clay

In the chemical reaction control regime employed in the laboratory dissolution experiments, calcined trona ore dissolves in aqueous solutions according to a first order, irreversible reaction rate. The study showed that the reaction is first order with respect to solution NagCO3 concentration. The activation energy was determined to be 20.233 kJ/g. mol with a rate constant equal to 1235 mm/s (2917 in. per min). The dissolving particle may be described by shrinking particle behavior.

Jan 1, 1986

By F. N. Kissell, W. E. Schroeder, N. I. Jayaraman

This article discusses methods of improving airborne capture by conventional dust suppression systems. The work was performed in a full-scale plywood model of a mine entry with a wooden mockup of a Joy 12 CM continuous miner. Dust was introduced at the front of the entry, and water sprays knocked down part of the dust cloud. Sampling in the return air determined the percentage dust reduction. Based on the results, guidelines are offered for continuous miner spray systems to control dust. Empirical relations have been developed to determine the effect of changes in water spray pressure on air movement, dust knockdown, and pollutant concentrations in the face return. Nozzle selection and arrangement are discussed for high dust knockdown efficiencies.

Jan 1, 1986

By W. D. Faulkner, J. E. Urbanic, R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in carbon-in-pulp and carbon-in-leach circuits has been investigated. Carbons from two US mines, one Canadian mine, and a South African pilot plant operation were characterized before and after regeneration. Thermal regeneration of the carbon was investigated using factorial analysis to determine the effect of interaction of furnace temperature, retention time, and use of supplemental steam. The operation of acid washing the service carbon was investigated, including a comparison of the use of nitric and hydrochloric acids. The effect of quenching regenerated carbon was also briefly studied. Prom the data obtained, guidelines are given for effective regeneration operation.

Jan 1, 1986

By J. E. Flinn, J. M. Welch, R. L. Miller

Introduction Two samples of an iron-enriched basalt (IEB)-a silicate-based fused-cast ceramic waste form-containing components that simulate Three Mile Island Unit 2 core debris were tested for uranium recovery (Miller et al., 1984). This material is highly refractory towards leaching by ground water. The uranium content is high (15.1%) and the U-235 content (2.57%, only

Jan 1, 1986

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be used to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters that are commonly used for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1986

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986