Search Documents

[ ]

Jan 1, 1938

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By L. Dudley Stamp

On April 1, 1937, Burma, formerly a province of the Indian Empire, was formally separated from India and became an independent unit of the British Commonwealth. In future, therefore, statistics of oil production in India will exclude Burma and those for Burma will be separately published. The last few years have been marked by noteworthy, almost spectacular, developments in the oil fields of Burma and the Punjab. In Burma these developments have been the proving of unexpected extensions of the existing fields and not the discovery of entirely new fields. The new extensions are important not only to Burma in giving a new lease of life to her fields, but also in general as stressing some interesting geological aspects hitherto neglected. Production The production of crude oil in Imperial gallons has been: Burma India 1934 254,760,070 67,265,210 1935 251,338,974 . 71,323,362 1936 265,656,393 69,241,504 1937 (eat.) 270,000,000 70,000,000 The Chindwin Fields.—The small field at Indaw continues to produce steadily about 3,000,000 gal. a year, but no really deep test has yet been successfully carried out and resources are thus not yet fully known. The remote location of the field, inaccessible except by river and situated 22 miles from the Chindwin 270 miles up that river from its junction with the Irrawaddy, has not encouraged active exploitation. The field is worked exclusively by the Indo-Burma Petroleum Co., Ltd. (I.B.P.), using now an automatic gas-lift system, and the company formerly refined the oil at a small refinery at Pantha on the river near by. The chief market was for kerosene in upper Burma. The refinery has now been closed. The oil is stored on the field during the low-water season

Jan 1, 1938

By Walter Miller

Construction of new large refineries was small in 1937, but extensive modernization and expansion of existing plants were made, bearing out the observation of the Bureau of Mines that the trend is strongly toward fewer and larger refineries. Building the first large combination skimming and cracking unit of 20,000-bbl. capacity was a startling achievement four or five years ago, but it has been exceeded many times since, and at least four units with a capacity of 30,000 bbl. or more were contracted for during 1937, as well as many other units of smaller but still substantial capacity. Installation of polymerization plants for producing high-antiknock blending naphthas from refinery gases progressed at an accelerated rate in refineries affording sufficient raw gas to make the use of the process profitable. The total productive capacity of polymerization units built and contracted for in the United States is now about 25,000 bbl., equivalent to the gasoline production from approximately 55,000 bbl. of crude oil a day. Octane Fuels Also utilizing refinery gases—the butylene fractions in particular—the plants for manufacture of iso-octane increased in number to such an extent that the combined capacities will enable the air forces of the United States shortly to go entirely to the use of 100-octane fuel, indications being that the Army will reach that position in 1938, with the Navy not far behind. Commercial air-lines are expected to take advantage of the greater power of high-antiknock fuels to gain the increased power and increased pay loads possible with their use. Work done on producing fuels with octanes beyond the 100 point has recently been reported, and their production can be expected, although at high cost, when the economics of the situation justifies and engines capable of utilizing them efficiently are available. In the field of motor fuels, important work was reported to the A.P.I. at its annual meeting, on the effect of altitude on antiknock requirements

Jan 1, 1938

By Donald Cummings

MEASURES appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-19 has accumu-lated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors-the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Con-trol of the danger arising out of prolonged contact with pernicious air-borne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects-one, medical; the other within the province of the engineer.

Jan 1, 1938

By L. S. Reid

THE study of the flow of oil and gas mixtures through oil-bearing formations has received special attention from the petroleum industry within the past few years, and has resulted in a series of research projects based upon various phases of the flow of heterogeneous fluids through porous media. Obviously, the low cost of producing oil during the flowing life of a well makes it desirable to obtain production by natural flow as long as possible and to effect a maximum recovery of oil and gas by the utilization of reservoir energy through efficient methods based upon a thorough knowledge of reservoir characteristics. Despite the extensive research that has been carried out, there is little information available on the behavior of oil and gas mixtures flowing through reservoir formations. This makes it impossible to predetermine the optimum operating condi-tions for flowing wells. A differential pressure must exist in the reservoir in order to induce flow toward the well. It is a well established fact that with homogeneous fluids the relation of pressure drop to linear distance traveled is a straight-line function as long as the flow is viscous. However, in regard to gas-saturated oils, a number of investigators1,3,4 have reported that the flow characteristics are materially altered as some of the lighter hydrocarbons are liberated from the oil to form gas while the fluid passes through the reservoir. Most of the work done has been concerned primarily with steady-state flow of liquid-gas mixtures. Cloud1 has studied the effects of saturating crude petroleum oils with various gases, together with the resultant pressure gradients under steady flow conditions, noting that unsaturated oils flowed faster and yet maintained lower pressure gradients than saturated oils.

Jan 1, 1938

By H. M. Day, C. H. Mathewson

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

[ ]

Jan 1, 1938

By Maurice L. Pinel, Thomas T. Read, Thomas A. Wright

THE erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1,11,12 but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until more and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: 1. 502 A.D. A pair (right and left) of recumbent lions (Fig. 1). Base 7 ¼ by 14 3/8 in., height over-all 5 ½ in., weight 26 lb. each. The translation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third year of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger 'proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

[ ]

Jan 1, 1938

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By L. W. Kempf, K. R. Van Horn

DURING the recent development of aluminum alloys for free-cutting screw-machine rod, it became desirable to know something of the solubility of lead and bismuth in liquid aluminum and in some aluminum alloys. The literature is not particularly helpful in supplying this information. These portions, therefore, of the constitutional relationships of aluminum-bismuth and aluminum-lead alloys were investigated by thermal analysis and by chemical analysis of samples taken from aluminum-rich melts in equilibrium with precipitated lead or bismuth. The solubility of lead and bismuth in some liquid aluminum-copper alloys was also investigated. Some consideration was also given to the solubility of these elements in solid aluminum. Among the earliest investigators of the aluminum-lead and aluminum-bismuth systems was Wright,1 who reported that melts of aluminum and lead formed two layers indicating limited liquid solubility. Under his conditions, the aluminum-rich layer was reported to contain 1.91 per cent Pb and the lead-rich layer, 0.07 per. cent Al. Subsequently, Pecheau2 found that in aluminum-rich alloy melts with more than 10 per cent Pb three layers were distinguishable. He reported that the middle layer contained from 3 to 10 per cent Pb. He also found that the melting point of aluminum appeared to be lowered slightly by the addition of lead. Gwyer3 investigated these alloys and found evidence of a slight lowering of the freezing point of aluminum by the addition of either lead or bismuth. He found no evidence of solid solubility in either case and made no attempt to determine the liquidus curves. Hansen and Blumenthal4 reported that the addition of lead distinctly lowered the solidification point of aluminum. They also found that bismuth lowered the melting point of aluminum. Guillet5 reported almost complete mutual immiscibility for the aluminum-bismuth alloys in the liquid state. Bohner6 examined the effect of various concentrations of lead and bismuth on the electrical conductivity of aluminum. He found decreases in conductivity on annealing at 500° C. as compared with the conductivity of the same alloys on annealing at 300° C.

Jan 1, 1938

By Charles Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metal-lography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method f compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform with-out fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orienta-tions resulting from recrystallization and is being extended to other metals and other types of deformation.

Jan 1, 1938

[ ]

Jan 1, 1938

[ ]

Jan 1, 1938

By W. A. Knoll

THE sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at, an average advance of 6 ft. per 24 hr. In November of 1930, experimental work was con-ducted oil 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be clone with vertical holes with the blasting relief to a 4 ½ -in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 511 ft. of the bottom at all times. This could not be clone without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.53 ft. per round of drilling, which was considerably more than the experience with a V-cut in the sane material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut.

Jan 1, 1938

By Howard N. Eavenson

From the Pittsburgh coal bed in the four states of Pennsylvania, Ohio, Maryland and West Virginia has been produced an output that, at mine prices, represents a greater value than any other single mineral deposit in the world has yielded.12 While this distinction may in a few years pass to the gold reef of the Witwatersrand, it is possible that eventually, owing to the tremendous reserves still remaining, the ultimate yield of the Pittsburgh bed will be greater than that of any other known single deposit. Considering its importance, not a great deal has been written of its early history and development as a whole; most of the accounts have been of limited localities, or, at the most, of the area within a single state. In "Coal through the Ages" the writer mentioned some references to its early history, but this study will deal not only with its history but with the character of the bed, where and why it was first developed, and its effect upon the states in which it is found. It has not been the intention to write a detailed history of the development of the seam in each locality, as neither time nor inclination were available for doing such work, but only to show the influences that tended to hasten or retard such development. In general the historical matter ends about 1830, when geological surveys began to be made. Some of the maps show data available only since that time, and the sections about coal preparation and coking have been extended to the present time to show the changing conditions. It is believed that the early history includes all published records, and many more sources than those shown in the bibliography were consulted. It is quite likely that some references to coal in this area may be found in the unpublished papers of some of our early soldiers and colonizers, which exist in several libraries, and it is hoped that some future * Dedicated to Dr. Thomas S. Baker, President Emeritus, Carnegie Institute of Technology, whose labors in promoting the International Coal Conferences and in establishing the Coal Research Laboratory have done much in showing the industry how science can be of help to it. Manuscript received at the office of the Institute Feb. 15, 1938.

Jan 1, 1938

By L. E. Porter

El Segundo field is about 14 miles southwest of the central portion of the city of Los Angeles, immediately adjacent to the town of El Segundo and the Standard Oil Company's El Segundo refinery site. The field is served and bisected by several major highways connecting the beach cities on the west side of the Los Angeles Basin. The exact location of the field and its position with respect to other producing areas is shown on the map covering this portion of the Basin (Fig. I). The Republic Petroleum Co. discovered the first commercial production in the area when it completed its El Segundo No. 1 (sec. 18, T. 3 S. R. 14 W.) at a depth of 7402 ft. on Aug. 24, 1935, flowing at the rate of about 400 bbl. per day, 28" gravity oil. The producing horizon in this well consists of about 72 ft. of conglomerate and schist conglomerate situated below the nodular shale (Miocene). The true (or solid) schist (Franciscan) was encountered and penetrated some 20 ft. in the bottom of the hole. This paper gives a report on the history of development and oil production to date, and also submits the writer's interpretation of structural conditions as determined from such development. The limited development, together with the complex and variable nature of the producing horizon, makes any interpretation of the structure at present only tentative, and any forecast for a given well extremely hazardous. History of Oil and Gas Production The El Segundo field has produced approximately 1,920,000 bbl. of oil. It has 27 producing wells and 14 drilling wells or locations. The present daily rate of production is about 13,400 bbl. The production history of the field to date is shown in Table 1. The principal companies operating or owning leases in this field are: Caminol Company, Geo. F. Getty, Inc., Ohio Oil Co., Republic Petroleum Co., Pacific Western Oil Corporation, Royalty Service Corporation, Richfield Oil Corporation, Standard Oil Company of California, The Texas Company, Union Oil Company.

Jan 1, 1938

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938