Search Documents

By Lachlan Gilchrist

MEASUREMENTS of resistivity by methods involving the use of two current electrodes and two potential electrodes in general collinear with the current electrodes have been made extensively in geophysical investigations. In the method developed by Wenner and made use of by Gish and Rooney, and later in a modified form by Lee, the distance between the current electrodes is divided into three equal parts by the potential electrodes. In one of the methods developed by Schlumberger prospecting methods and by Koenigsberger, one current electrode is placed at considerable distance from the other and potential measurements are made in the immediate neighborhood of one of the current electrodes. The method is described as the single current electrode method, and the effect of the distant current electrode is considered negligible or a correction is made for the effect in the calculation of the resistivity. Usually the correction that is introduced is based on the calculated effect for measurements made in a homogeneous conducting material. The useful application of these methods in prospecting for minerals, of course, is in regions where nonhomogeneous conditions exist. In many of these conditions it is very doubtful whether the effect of the distant current electrode may be neglected, except for measurements in the immediate neighborhood of the "single" current electrode, and corrections based on homogeneity of the medium will necessarily be inadequate. In order to obtain a degree of symmetry that would preclude the necessity for corrections for the distant electrode and that would simplify interpretation, it appeared desirable to use a central current electrode and a set of distant end current electrodes symmetrically placed about the central electrode as shown in Fig. 1 and to provide by means of auxiliary resistances that the currents passing into the earth at the distant end electrodes should be equal. Circumstances did not permit the operation of this plan in complete detail but a degree of symmetry was obtained by using a central current electrode and two distant collinear end current electrodes and by taking measurements along a line passing through

Jan 1, 1931

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By C. R. Hocott

THE viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,1,2 but no data have been published on the viscosity of repre-sentative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields.

Jan 1, 1940

By Gerald Sherman

MINE fires are always dangerous and are frequently accompanied by loss of life during the period of confusion which is apt to follow their discovery. In metal mines, fires may result from the accidental ignition of some combustible material, or they may be of spontaneous origin resulting from the rapid decomposition of sulphide. They occur frequently enough to demonstrate the need of some special equipment and a general plan for controlling them, in addition to measures for their prevention. Nearly all the large copper mines have had fires, and the methods of fighting them have been well described in recent papers, notably-by C. L. Berrien,1 R.. E. Tally,2 and others in discussion. The Copper Queen mine has many shafts, which are connected by underground workings. The deeper parts are ventilated by fans, but in the shallower portions natural ventilation through numerous connecting raises or shafts is sufficient. There have been several fires in the past few years, of which all are extinguished but one, and that is under control. These notes cover particularly the preparations that are being made-to check a new fire, partially or temporarily, and to facilitate the escape of workmen in the interval before a definite plan of fighting it can be established. A fire may occur in a shaft or station, or in some working father away. In case of fire in an upcast shaft, the gas would escape to the surface and the immediate result would probably not be dangerous to workmen, as they could escape by other shafts. In a downcast shaft, however, the gas would be distributed very rapidly throughout a large portion of the mine, and men might easily be trapped and asphyxiated. A fire in mine workings, drift, raise, or stope, would be dangerous in a degree, but the draft there is likely to be less strong than in a shaft and probably a smaller area would be invaded by the fire gases.

Jan 1, 1918

ROBERT E. TALLY,* Jerome, Ariz. (written discussion ?).-Mr. Sherman's paper, entitled "Measures for Controlling Fires at the Copper Queen Mine," embodies two new and very important features: First, automatic closing of doors communicating with the dangerous area; second, the use of a portable storage-battery fan. His other procedures, such as giving a general fire alarm, getting workmen to the surface, etc., are equally important, but have long been in use in other places. Fire and ventilating doors in connections leading to shafts, air raises, and other large timbered areas, have been in use at other mines; but the method described by Mr. Sherman for operating these doors by compressed air, through a valve on the surface, is, so far as I know, original, and should be installed in every mine where there is danger of fire. Nearly all large mines are now using artificial ventilation, with the result that there are strong air currents in the shafts and other important workings. The most important feature in mine fires is a quick and positive control of the ventilation, for it takes but a few moments for smoke to travel over a large area, with the usual results of suffocation, and destruction of property. A strong air current in an upcast shaft acts as a draft in case of fire, and unless quickly cut off the fire would soon get beyond control. An upcast shaft usually changes to a downcast when large amounts of water are used. Human lives are in more danger from downcast currents, as the smoke travels into the workings.

Jan 4, 1918

By William E. Bruce

This paper is intended to provide an improved understanding of natural draft (natural ventilating pressure) and the effect of natural draft on underground mine ventilation circuits. Attention is focused on measurement of natural draft pressures during ventilation surveys in mechanically ventilated mines and on different methods for modeling natural draft using the measured data. A number of examples are presented which utilize data collected during absolute air pressure surveys made by personnel of the Ventilation Division of the Mine Safety and Health Administration's Safety and Health Technology Center, Denver, Colorado. Examples are used to illustrate how the data from absolute air pressure surveys may be interpreted to determine whether natural draft pressure is present and what its magnitude is. In addition, two different methods are described for mathematically estimating the magnitude of the natural draft pressure. Comparisons are made of results obtained using the different methods. Different procedures are described for modeling natural draft using the MSHA-modified Penn State computer program. Use of the routines is described and illustrated relative to drafts that aid or oppose the mechanical ventilation system. Tabulations of results facilitate comparison of outcomes obtained using the different modeling procedures.

Jan 1, 1982

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per 100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series, for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship p to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distributi0n line is [w = Cx" [I]] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series,1 for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship [p] to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distribution line is w = Cxm [I] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By Brooks J. Klimley, Daniel M. Higgins, Grover R. Castle

Measuring The Economic Viability Of Resource Projects (A Western Surface Coal Project) The bankers approach to the analysis of a new "green fields" mining project is similar but different from the approach that the pining company might take. The purpose of this paper shall be to discuss the techniques that are used by mining companies and bankers as they try to measure the economic viability of mining projects. The analysis of these new projects (by both the mining companies and the banker) is based on a projected revenue stream and not on historical earnings or past perfomance because these projects are start up situations with no history to look to. The starting point in the analysis of these projections is the choice of the assumptions to be used in preparing these projections. After the assumptions have been determined and the projections are prepared then the projections are submitted to various tests in order to determine whether the project measures up to previously agreed upon minimum standards. In order to illustrate the analytical procedures used in evaluating a mineral project the writer has constructed a hypothetical case involving the development of a western surface coal mine (Property). The basic data in connection with this hypothetical new project is described in the next section of this paper. After the Description of the Project is a section which shows the type of analysis that a mining company might prepare in order to approach a bank for a loan and the final section illustrates the type of analysis that a bank might prepare in evaluating this loan request. Description Of The Project or Basic Data In Connection With Undeveloped Western Surface Coal Property An independent mining/geological Consultant's report has been completed on the Property which confirms that the Property contains 175 million tons of economically recoverable coal subdivided into the following reserve categories in accordance with U.S. Bureau of Mines and U.S. Geological Survey definitions: Measured or Proven 90,000,000 Indicated or Probable 50,000,000 Inferred or Possible 35,000,000 The owners of the reserves have chosen to drill up those reserves that are nearest to the subcrop and have not spent as much time on those portions of the Property which are on the fringes of the deposit where the overburden is thicker because the stripping ratio and hence the operating costs and capital requirements are higher down dip. The proven reserves are based on an average thickness of 80 feet, of which a mining recovery of 90% is projected. The overburden thickness varies from 0' to 280' with an average thickness of 127'. The overburden consists mainly of scoria, sandstone, gravel, shale and silty clay. 134 holes were cored (and analysis done on five foot increments) in the measured reserve on the following spacing: 100 foot centers to define the burn line; 1,320 foot centers to define the early mining areas; 2,640 foot centers to identify the later mining areas.

Jan 1, 1985

By R. Lingle, E. Hardin, M. Board, H. Pratt, W. Ubbes, M. Voegele, N. Barton

A 2 m. cube of jointed, Pre Cambrian biotite gneiss was subjected to uniaxial and biaxial loading at ambient and elevated temperature. The effects of different boundary conditions on the following rockmass properties were investigated: deformation modulus, joint stiffness, dynamic modulus, coefficient of thermal expansion, thermal diffusivity and conductivity, and joint permeability. Test conditions ranged between 0 and 6.9 MPa uniaxial and biaxial load, and 12° to 74°C mean block temperature. The tests were performed as part of the Office of Nuclear Waste Isolation program for evaluating site charterization test methods for measuring the hydro-thermal-mechanical properties of rock masses. The fracture flow experiments discussed in this paper were described in detail in a similar paper given to this symposium in 1981 (Voegele, 1981). DEFORMATION MODULUS Horizontal deformation measurements oriented parallel to the loading direction were made at the block surface. Several instrument types were employed: surface short-rod extensometers, bonded strain gauges, vibrating wire strain gauges and the Whittemore caliper strain gauge. Two vertical and two slant borehole extensometers measured vertical displacement. Loading history, especially during uniaxial loading, was critical to interpretation of observed deformation and fracture flow data. This important tendency has been observed in other large-scale laboratory (Bandis, 1980) and field tests (Pratt, et al., 1977). Excavation of the block resulted in minimal disturbance to the intrinsic condition of the sample. Even so, permanent, unrecovered "set" was imparted to the block beginning with the first low-stress biaxial load cycle to 3.45 MPa (Table 1). Unloading

Jan 1, 1982

By Arthur F. Taggart

MR. CHAIRMAN: Congratulations! Your four-ring milling show this year was a dandy. It cleared our minds, for a few hours at least, of what Hitler, Hirohito, the New Deal, and the tribe in the Treasury are trying to do to strangle American enterprise. We mustn't forget this, but it's a relief to get our thoughts away from it occasionally. GRINDING-There was a further contribution to the excellent work that the Allis-Chalmers laboratory staff has been doing for the grinding fraternity in compiling-and publishing-a carefully quantitative list of comparative resistances of ores and other materials to comminution (T.P. 1579, Bond-Maxson). A diagnostic accuracy of ± 10 per cent was claimed for estimates based on these figures. Are they really that good? How about some of you men in the field writing M&M about it?

Jan 1, 1943

Two 6.17-m-diam (20.25-ft) shafts, said to be the largest ever opened with mechanical raise boring techniques, were completed in May and June 1978, at Monterey Coal Co.'s No. 1 mine near Carlinville, Ill. According to the shaft contractor for the project, Frontier-Kemper Constructors, the openings are 60% greater in cross section than the largest previous raise-bored shaft, which had a diameter of 4.85 m (16 ft). Both vertical shafts are 93 m (305 ft) in total depth, with the upper 28-30 m (90-100 ft) sunk and lined by conventional methods through unconsolidated overburden and the remainder mechanically bored through sedimentary rock. The two shafts will be used for service access as well as to augment ventilation.

Jan 12, 1978

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal-dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so that the terms which are defined in this chapter should be regarded mainly as working terms intended to facilitate communication. A coal slurry ' might be defined as a watery suspension carrying particles of fine coal and other assorted material ranging upward in size from the finest clay particles. Some particles may be in the colloidal sue range and exhibit characteristics of suspended colloids. The dilution of the system generally is such that it is in a condition of independent particle subsidence. In some coal mining areas a slurry is regarded as a suspension of fine coal and other materials having a dilution that cannot be economically dewatered by filtration. A coal slime may be regarded as a slurry containing particles of such size range that 50 per cent or more (by weight) will pass a 200-mesh sieve. Slime suspensions generally are difficult to handle without special treatment in conventional sedimentation equipment. A coal sludge is defined as a slurry that has been partly dewatered by sedimentation usually to a thick or viscous consistency where further dewatering can be most readily facilitated by filtration. Culm and silt are terms characteristic of coal-preparation practice which should be defined. In anthracite terminology, culm is the generally coarse residue or waste accumulation of coal, bone and rock from preparation plants most of which are no longer functional. Culm has a wide range of sizes, some rather coarse, and except to differentiate it from silt, the term is of limited interest in this discussion. In anthracite terminology, silt is the accumulation of waste fine coal, bone and slate settled out from preparation plant water in excavated basins. Silt is generally made up of particles ranging in size from 3/32-in. round-opening screen to the very finest sues. Silt is also referred to at times as sludge, fines, slush, and mud and is the partly dewatered derivative of what has been previously defined as slurry. In the terminology of the bituminous coal producing areas, the word culm commonly corresponds to slurry or slime, depending upon the size distribution of the suspended solids. Editor's Note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections authored by each individual as is the case in most chapters of this book.

Jan 1, 1968

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so the terms defined in this chapter should be regarded primarily as working terms intended to facilitate communication.

Jan 1, 1979

By H. C. Miller

THE gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas lift possible, or where natural gas is plentiful and inexpensive. We find therefore in California, that, natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanied the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the. tubing and flow lines. The gas lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecranz field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas lift it approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1927

By H. F. McCullough

MECHANICAL loading and conveying equipment has been available for the coal-mining industry for more than twenty years. The earlier equip-ment-was admittedly crude and ill-fitted to perform its intended functions, but there are available today a variety of mechanical loaders and conveyors which may be said to be almost on a par with coal-cutting machines. Despite the fact that such equipment is available and that better and other types of equipment are continually being developed, mechanical loading of coal cannot yet be said to be economically successful, except in a few special cases. It is not an accomplished fact in the sense that machine cutting of coal and electric haulage are accomplished facts and a part of accepted practice. There are two general opinions why we have failed to obtain better results with mechanical loading and con-veying equipment. The equipment manufacturers will say that coal-mine operators have generally failed to establish and maintain the conditions required for suc-cess. The coal-mine operator says that the equipment is not adapted to cope with his specific conditions to the extent required for economically successful results. Just what is the objective of this movement toward mechanical loading? We speak of mechanical loading in such a way as to lead one to believe that we are mere-ly seeking a mechanical equivalent of the human loader and his shovel. Really, we are impressed with the fact that the coal-mining industry has not advanced toward greater productive efficiency to anything like the degree achieved by practically all of the other productive in-dustries, and we are seeking the means to remedy this. We have seen the advantages which follow the intro-duction of coal-cutters and electric haulage-locomotives. The loading of coal is the one major operation in coal mining which has not been mechanized. We believe that a satisfactory, mechanical substitute for the man with the shovel will help us increase our productive efficiency to the same degree as has been accomplished in the other productive industries.

Jan 3, 1927

TWO hundred enthusiastic engineers and coal, op-erators attended a joint meeting of the A. I. M. E., the National Coal Association, and the American So-ciety of Mechanical Engineers in the auditorium of the Alabama Power Co. building at Birmingham, Ala., on Jan. 21. S. W. Farnham, mining engineer of the Goodman Manufacturing Co., Chicago, in his paper on mechanical loading of coal discussed the feasibility of scraper and machine loading. A. R. Anderson of the Jeffrey Manufacturing Co., in a paper on loading coal with conveyors covered their adaptation for long-wall mining and for loading into cars. Discussion of these papers was hampered because the cheap labor costs prevailing in the district have handicapped gen-eral mechanization of the mines. The Bureau of Mines film, "The Story of a Rock-dusted Mine," showing the New Orient mine, West Frankfort, Ill., was also shown at the meeting. F. H. Crockard, president of the Wood-ward Iron Co., represented the A. I. M. E., S. L. Yerkes, vice-president of the Grider Coal Sales Agency, and J. L. Davidson, secretary of the Alabama Mining Institute, represented the National Coal Association, and Paul Wright represented the American Society of Mechan-ical Engineers.

Jan 2, 1927

By S. W. Farnum

ABOUT three years ago at a coal mining institute meeting, it was predicted that mechanical load-ing underground would progress faster than either the electric coal-cutting machines or electric loco-motives had in previous years. This prediction has proved correct so far. In 1925 over 6,000,000 tons of,coal was loaded mechanically underground in the United States and it is estimated that the 1926 tonnage will reach 10,000,000. The use of electric mining machines and locomotives .has prepared the way for quick results. Most coal mines are now equipped with electric power and have a competent staff who understands its use. In spite of this advantage the introduction of the loading machines brings many new problems. Im-proved and concentrated transportation; doing the drilling, shooting, tracklaying and face timbering with company men instead of the former tonnage men; doing the work on the new basis in an economical and efficient manner; altering or modifying mining systems where necessary to further improve the work and reduce oper-ating costs; improving the percentage of lump coal and reducing the slack content where desirable; improving the cleaning of the coal and obtaining a more dependable .and uniform output are a few of the problems that must be met. Each of the different types of loaders now on the market has its particular advantages and disadvantages for a given mining condition. Even with the same mining conditions one type will work well under one ;system of handling, whereas another may favor another system or mining method.

Jan 5, 1927

By G. Stuart Jenkins

CONDITIONS at the properties of the Consolidated Coal Co. had reached a point where improvements were almost impractical. The mines, sunk years ago, had shafts and entries so small as to preclude the use of large mine cars. A radical change was necessary in the type of mining and also in the type of mine to accommodate such haulage units. After due consideration, the company decided to enter the field of trackless mining, utilizing belt conveyors and chain-flight conveyors, the belt conveyors to take the long haul, and the chain-flight conveyors to be used for gathering. It was decided not to sink a shaft, but to drive a slope on an inclination of 17 1/2°, which the company believes to be about the limit on which coal can be carried on a belt without rolling back unduly.

Jan 1, 1939

By Herbert Kynor

BY THE term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal & Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal & Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910a is as follows: PENNA. COAL Co. D. L. & W., SCRANTON TEMPLE HUDSON YEAR AND HILL- TONS COAL Co., COAL CO., COAL CO., TOTAL. SIDE COAL TONS TONS TONS TONS AND IRON, TONS 1920 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919 950,786 no record 306,616 81,575 319,356 1,658,333c 1918 917,778 744,966 24,880 44,756 288,781 2,021,161 1917 757,940 838,800 5,050 57,279 164,180 1,823,249 1916 286,780 860,663 13,960 114,173 101,475 1,377,051 1915 428,819 592,169 8,253 1,029,241 1914 219,188 153,896 373,084 1913 171,505 171,505 1912 124,267 124,267 1911 40,319 40,319 1910 1,184 1,184 a. A slightly greater production than shown was obtained as the tonnage from individual operations is not shown. b. Decrease due to strike conditions in 1920. c. Does not include tonnage of D., L., & W. d. D., L., & W. decrease in 1920 due to having less mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 9, 1921