Search Documents

By Edgar C. Bain

A NUMBER probably a sizable group of person with a dominant interest in metals maintain contact with the developments in ferrous metallurgy by reading week by week, as time permits, some four or five periodical devoted in considerable part to this field. It seems possible that some of these, like ourself, find it difficult to see the net results of the development day by day in clear perspective, The impression sometimes seems blurred by the uninterrupted succession of so many accounts, or out of focus from the very impact of so many reports of new things enthusiastic, well written, and understandable though they usually are. It is at times almost as though one were trying to observe, from a fastmoving vehicle, objects all too near at hand. Or perhaps this impression is merely a manifestation of our individual hyperopia ; in which case we should content ourself with an observation that it would be more satisfactory on the whole to discuss in 1941 the metallurgical advances of 1930-35 than those of

Jan 1, 1941

By Franklin H. Allison

The influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such 3 remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of properties that are obtained from steel is due largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allot ropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1500" F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident. Effect of Nickel and Cobalt in Binary Alloys with Iron The binary diagram of iron-nickel has been investigated by a number of workers. The lower temperature portion in Fig. 1 is reconstructed from the data of D. and H, Hanson.1 The diagram of iron-cobalt, shown in Fig. 2, is taken from the work of Ruer and Kaneko.2 Masumoto3 has recently discovered a lower critical point in cobalt and this has been added to the diagram. In both diagrams the space lattice structures as determined by Andrews4 have been included. It is interesting to note

Jan 1, 1927

Jan 1, 1928

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By C. H. Herty

The results of a study of the open-hearth process from the physicochemical viewpoint are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. The effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styril from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900' F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,a Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 1, 1926

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By J. M. Gaines, C. H. Herty

It is a matter of frequent record in the literature that manganese will desulfurize molten iron under proper conditions. Particularly has much been written with regard to this action in the mixer, and numerous reports have been published describing experiments in which advantage was taken of this phenomenon in order to obtain a purer iron for the open hearth. The question of sulfur elimination in the ladle has, however, received comparatively little attention. The reaction by which sulfur is removed is considered to be: FeS + Mn = MnS + Fe. The manganese sulfide, being but sparingly soluble in the iron, and of a lower density, will rise from the body of the metal and collect as a slag on the surface. It is therefore an action taking place solely in the metal, and independent of interaction between slag and metal. As will be shown later the presence of slag on the metal tends to offset the effect of manganese elimination. It is this fact which distinguishes desulfuriza-tion in the ladle from desulfurization in the mixer, for it has been shown1 that the amount of sulfur eliminated in the mixer is closely tied up with the composition of the slag. Experimental Procedure In order to ascertain the extent of and the factors controlling this elimination in the ladle, several casts were sampled carefully at the blast furnace and again when the ladles were being emptied, either at the mixer, open hearth, or foundry. If the sulfur content varied from ladle to ladle at the blast furnace the average sulfur content of each ladle was obtained by integrating the curve "sulfur vs. time " for the cast under

Jan 1, 1927

By L. S. Darken

It has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernstl in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and FuossZ with results which have recently been confirmed experimentally by Harned and Nuttall. This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author,4,5 who pointed out4 that "for a system of more than two components it.is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepti- cism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley" in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion of acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 10500 C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1949

By J. E. Crawshaw, Francis B. Foley

In the first report1 disks of steel of known composition and history were exposed, under carefully prescribed conditions, to impacts of explosion products resulting from the explosion of 50-gm. charges of explosives having well-determined rates of detonation, or to impacts of a weight of known mass, falling through measured distances. There were available at the Bureau of Mines Experiment Station five explosives, having rates of detonation of 5716, 4470, 3190, 2296, and 1523 meters per second. It being desired to continue this exposure downward, and no explosives with a lesser rate of detonation being at hand, resort was had to the impact of a falling weight, the differences in the velocity of impact being attained by varying the height from which the weight was allowed to fall. It was expected by this means to demonstrate experimentally that the development of Neumann bands was determined by the suddenness of the deformation of the metal in which they were produced. But while progressive deformations were obtained with the explosive charges, the falling-weight method failed because the tup was progressively deformed, also the disks were so flattened as to be unfit for metallographic examination. A return, therefore, has been made to the use of explosives as the source of energy, an air-gap being interposed between the charge of explosive and the disk, as the effect diminishes as the function of the distance between the charge and the object on which the products of its explosion, or the shock wave from its detonation, impinge. The details of the arrangement of the tests by the air-gap method were the same as those described by Foley and Howell,2 except that after the system had been set up and the desired apparent specific gravity for the explosive attained by tamping it, the small lead block, with the steel disk adhering

Jan 1, 1926

By C. H. Herty, J. L. Keats

In the literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical characteristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete data as possible on all the factors that affect the elimination of metalloids were obtained. The Test Heat The test heat was made in a standard 100-ton stationary furnace at the Lackawanna Steel Co., Lackawanna, N. Y., on January 17, 1922. The Charge—Scrap.—The scrap consisted entirely of rail-heat butts, selected from a number of heats made the week before the test. The average analysis of the scrap was calculated from the analysis of these heats and from the weight of scrap from each heat. Pig Iron.—Two ladles of pig iron were used in the charge and two samples were taken from each ladle as it was poured into the furnace. These four samples were composited for the average pig-iron sample. Other Materials.—Weights of dolomite, ore and spar were obtained by weighing a quantity of each just before the test and weighing the amount of each left after the heat was completed. The limestone. was weighed on the charging pans. Coal for recarburizing, ferromanganese, ferro-silicon and aluminum were weighed out as used. All these materials were carefully sampled before the test was begun. Coal consumption at the producers was obtained by getting the average capacity of the hoppers that fed the producers, and then counting the number of hoppers of coal used during the course of the heat. Products Steel.—The steel made was rolled into billets, the rolling properties being very satisfactory. The weight of steel was obtained by taking a

Jan 1, 1926

By Sir Albert E. Kitson

The manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In certain respects they have a strong resemblance to those of India and Brazil, as contrasted with those of Tertiary age in Georgia, but in this paper no careful comparison with them can be made. Viewed from the present condition of the manganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments. Youngest are the products of decay and degradation with the concentration of manganese oxide in the rocks of both groups. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate degree of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows, largely of basic types. This has been named the Birrim System. Its age is unknown, for no definite fossils have been discovered in it. Since these non-fossiliferous strata at many plaees are of a character which in many parts of the world are suitable for the preservation of fossils, and which contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim System have normally a northeast-southwest strike, and are folded, but not to any very great degree except in certain belts. From the Eastern Province of the Gold Coast they may be traversed diagonally across their strike for upwards of 600 miles, to the extreme northwestern corner of the Northern Territories. Thence they probably extend much farther into French territory.

Jan 1, 1927

By M. J. R. Morris

THE year 1939 has seen the iron and steel industry driving for efficiency with unabated zeal. "Efficiency" is here used in the sense of enabling the customer to do more with less, either supplying him with more economically priced steels or with higher priced steels that will do a job more economically. The plain carbon steels have been improved tremendously in quality be- cause of recent control tests. All steel companies have been urged to hold to .closer chemical control, closer standards, soundness, and more control on grain size, and now attention is being directed to closer control of hardening properties. Better control of open- hearth operations undoubtedly will result in an increase in the application of special carbon steel. Further, with a better understanding of quenching, the present trend to study the quenching of this class of steels will be ex- tended. These steels will then be used for purposes to which they are best suited. Utilization of special carbon bars and large shapes seems to be developing less slowly than special car- bon in the form of strip. There are many reasons for this and the future development of this trend will be important. Continued development of the manufacture of parts from strip and sheet to replace forgings, and of formed; structural members such as channels or welded pipe, is notable. Special carbon sheets with nonaging properties have been produced during the year; they maintain a higher degree of ductility over a longer time and are less sensitive to the changes which took place in the former product when stocked.

Jan 1, 1940

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

.In a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. Consequently since a technical cohesion limit is defined as the technically deter-minable resistance to fracture under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. In the general investigation described in the previously-mentioned papers, 10-18,20,21,23 the influence of the stress system on the fracture stress was studied by means of tension tests of notched specimens. When a circumferentially notched cylindrical specimen is subjected to longitudinal tension, the minimum cross section is under transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S1), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (Sz = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (s3/s1) The evidence is based not only on the results of tests to fracture at various constant temperatures, but also On results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1949

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By Sir Robert Hadfield

Table 1 gives the composition of the specimens listed by the author. The details of test procedure and the results of the tests on mechanical, magnetic and electrical properties and cor-rodibility of the alloys are published in full in a paper by the same author, "Alloys of Iron and Manganese Containing Low Carbon," presented before the Iron and Steel Institute (of Great Britain) and published in full in their Proceedings for 1927, to which reference should be made. After reporting these tests the author gives the following discussion of results:] The studies here reported do not indicate that any of the series has really valuable or useful qualities for industrial applications, though the demands of industry are so varied that it is unsafe to prophesy that no special use will be found for a given material. The non-magnetic property of manganese steel is due to the association of Fe and Mn, but carbon has also an effect, enabling non-magnetic qualities to be obtained with a much lower percentage of Mn than would otherwise be the case; for example, 16 per cent. Mn is necessary for alloys practically free from carbon, while with 1 per cent. C nonmagnetic alloys may be obtained with as little as 7 per cent. Mn. Carbon, however, is the prime cause of the development of magnetic qualities by heat treatment. (Sec section 8 of the paper referred to above.) These Fe-Mn alloys show a resistance up to 87 microhms per c. c., but. as there are other alloys which have a resistance as high as 130 microhms per C. c., this does not provide any new feature of value. The most marked feature of the series studied is the brittleness in the range 3 to 10 per cent., with a maximum of brittleness at 7 per cent. Material with this percentage, while possessing quite appreciable hard-

Jan 1, 1927

By Carl Pierce

The writer of this article has not attempted to write a technical paper; on the contrary, he has tried to express in "steel-plant English," for steel men, a viewpoint drawn from his practice and experience. It is not his thought that it shall be taken as the "last word" in the making of this class of steel, or that good rimming steel cannot be made by any other practice. The paper was written to serve as the basis of a discussion from which it is hoped much benefit may be derived. The paper deals only with rimming steel made by the open-hearth process, and with the lower carbon steels, such as sheet and tin bar, rivet stock, skelp, etc., although good rimming steel as high as 40 to 50 carbon can be made by having good open slags and giving proper attention to working and tapping temperatures. Definition of Rimmed Steel Rimmed steel is sometimes called open or effervescing steel to differentiate it from killed or partly killed steel. It is steel made by a process which permits the free escape of gases from the metal in the molds. In passing up through the metal, the gases keep it in a rolling action from the walls of the mold inward. The top of the ingot rims in as the metal chills and the walls of the ingot get thicker, the center part remaining fluid until it reaches a pasty condition when it is covered with a cast-iron cap. The Charge In making up a charge for rimming steel, clean stock of a known composition must be selected, special attention being given to the analysis of the materials. The silicon in good rimming steel must be eliminated to a trace, therefore it is advisable to have a uniform amount going into the charge. Too much silicon gives a raw melting heat from which rimming steel is unlikely to result. For this reason a charge containing not to exceed 40 per cent. pig iron and 60 per cent. scrap, with no iron ore, is preferred to the Monell type of charge in which as high as 65 to 70 per cent. pig iron is used with a proportional amount of iron ore for the removal of the excess silicon and carbon. The silicon content of pig iron varies so much from day to day in the average blast-furnace practice that there is danger of getting too much of this element in the latter mixture when

Jan 1, 1926

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.' After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927

By Frank T. Sisco

DURING the past year the iron and steel industry of the world as a whole operated on a satisfactory basis. No discoveries nor new processes of outstanding importance were announced either here or abroad, although rumors of such were persistent. In general, the efforts of operating and research men in the iron and steel industry seemed to be confined to improving quality and reducing cost, not a new aim, for the same efforts have been noted in nearly all of the annual reviews of the industry for at least fifty years. Most published papers on blast furnace or steel-making practice were of minor importance, at least when judged by the criterion of radical change in process or product. If the number of reports in the technical journals, or articles in the trade press, is used as a basis for comparison, continuous-mill sheet is still the most important single product of the industry; papers were published detailing the results of the investigation of various phases of the

Jan 1, 1938