Search Documents

By A. M. Gaudin

IN flotation lime is used to depress pyrite. For this purpose it is preferred to caustic soda. The low cost of lime and the widespread availability largely account for this preference. However, there is some evidence1 that pyrite is more readily depressed by calcium than by sodium ions at the same pH. To measure the difference in adsorption of calcium and sodium, which is thought to lie at the basis of the differences in depressing action, radionuclides of

Jan 2, 1953

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid- fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made.1 Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system.

Jan 12, 1954

By A. M. Gaudin, Olav Mellgren, P. L. De Bruyn

In commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite. In the work on chalcocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh,,' but the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5; at neutrality. a contact angle of 60° is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants.

Jan 1, 1956

By P. Somasundaran

Adsorption of a nonionic polyacrylamide (PAM), an anionic polyacrylamide with sulfonate functional groups (PAMS), and a cationic polyacrylamide with amine functional groups (PAMD), on hematite was investigated as a function of different solution conditions. Adsorption results indicate that the major mechanisms of adsorption of polyacrylamides on hematite is through hydrogen bonding, with electrostatic forces playing a secondary role. All the polymers exhibited irreversibility of adsorption upon dilution. Also, entropic effects were determined to be important in adsorption. Surface chemical properties of hematite and solution chemistry of the polyacrylamides are considered to explain the polymer adsorption behavior on hematite.

Jan 1, 1985

By Alexander Knoll, Dwight L. Baker

THIS paper is a report on work undertaken to investigate the results and conclusions of Ravitz and Porter1,2. that galena freed of surface oxidation products and lead carbonate ("clean" galena) is water-repellent, and that the action of xanthates in flotation is the action of a cleansing agent, enabling oxidized galena particles to expose a pure lead sulphide, water-repellent surface. The apparatus, in construction and use, was essentially that of Ravitz and Porter. The only significant modification introduced by the present authors was the substitution of a three-necked flask for the flotation cell as the "reaction vessel." Our procedure was to place 50 grams of freshly ground, minus 200-mesh galena in the reaction vessel, sweep out all molecular oxygen from the system with oxygen-free nitrogen, and proceed to wash the galena surface free of its oxidation products with repeated small portions of (I) ammonium acetate (500 c.c. of water, 200 grams of ammonium acetate) or (2) ammonium chloride, hydrochloric acid (2 liters containing 200 grams of ammonium chloride and 25 c.c. of 1.18 sp. gr. hydro chloric acid). The galena was next washed with many 100-c.c. portions of oxygen-free, distilled water. The galena was finally considered free of soluble salts when wash water that had been in contact with the mineral for at least 48 hr.* gave negative tests for: (I) lead ion with sulphide; (2) chloride with silver ion; (3) acetate with cuprous chloride, sodium chloride; and (4) ammonium ion with Nessler's reagent. Next 500 c.c. of potassium ethyl xanthate solution, free of dissolved oxygen, was run onto the "clean" galena particles. For this system there were determined: I. The wetting properties of the clean galena particles by shaking the reaction flask and noting the degree of mineral collection at the liquid-air interface. This was, of course, simply a qualitative test, but it proved adequate for our purpose. 2. The removal of xanthate ion from the potassium xanthate solution on being shaken with the "cleansed" mineral. Xanthate concentrations were determined by iodine titration according to the methods of Taylor and Knoll.3 3. The pH of the xanthate solution after having been shaken with the "cleansed" galena. The pH was determined colorimetrically.4 The results of five experiments of the type mentioned above are given in Table I.

Jan 1, 1941

By Alexander Knoll, Dwight L. Baker

THIS paper is a report on work undertaken to investigate the results and conclusions of Ravitz and Porter1,2 that galena freed of surface oxidation products and lead carbonate ("clean" galena) is waterrepellent, and that the action of xanthates in flotation is the action of a cleansing agent, enabling oxidized galena particles to expose a pure lead sulphide, water-repellent surface. The apparatus, in construction and use, was essentially that of Ravitz and Porter. The only significant modification introduced by the present authors was the substitution of a three-necked flask for the flotation cell as the "reaction vessel." Our procedure was to place 50 grams of freshly ground, minus 200-mesh galena in the reaction vessel, sweep out all molecular oxygen from the system with oxygen-free nitrogen, and proceed to wash the galena surface free of its oxidation products with repeated small portions of (I) ammonium acetate (500 c.c. of water, 200 grams of ammonium acetate) or (2) ammonium chloride, hydrochloric acid (2 liters containing 200 grams of ammonium chloride and 25 c.c. Of 1.18 sp. gr hydrochloric acid). The galena was next washed with many 100-c.c. portions of oxygen-free, distilled water. The galena was finally considered free of soluble salts when wash water that had been in contact with the mineral for at least 48 hr.* gave negative tests for: (x) lead ion with sulphide; (2) chloride with silver ion; (3) acetate with cuprous chloride, sodium chloride; and (4) ammonium ion with Nessler's reagent. Next 500 c.c. of potassium ethyl xanthate solution, free of dissolved oxygen, was run onto the "clean" galena particles. For this system there were determined: I. The wetting properties of the clean galena particles by shaking the reaction flask and noting the degree of mineral collection at the liquid-air interface. This was, of course, simply a qualitative test, but it proved adequate for our purpose. 2. The removal of xanthate ion from the potassium xanthate solution on being shaken with the "cleansed" mineral. Xanthate concentrations were determined by iodine titration according to the methods of Taylor and Knoll.3 3. The pH of the xanthate solution after having been shaken with the "cleansed" galena. The pH was determined colorimetrically.4 The results of five experiments of the type mentioned above are given in Table x.

Jan 1, 1941

By A. M. Gaudin

A preliminary study of silver ion adsorption by sphalerite in ion exchange column with influent electrolyte marked with radiosilver is described. Rapid ion exchange occurs at first followed by slow reaction controlled perhaps by solid state diffusion. One experiment with radiocopper instead of radiosilver is reported briefly.

Jan 9, 1951

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na' activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - 'Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

By K. S. Choi, B. S. Shin

The adsorption characteristics of sodium silicate on scheelite, calcite, and fluorite minerals were investigated. Adsorption equilibrium took about 60 minutes. Adsorption data show that the masimum amounts of adsorption of sodium silicate occurs at about pH 9.8. The adsorptivity was in the order of calcite > fluorite > scheelite. The amount of adsorption of sodium silicate increased with the increase in temperature of sodium silicate solutions. The amount of adsorption of sodium silicate decreases in the low concentration range of ferrous sulfate, while in the high concentration range of ferrous sulfate, the adsorption of sodium silicate increases.

Jan 1, 1986

By J. H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the pH range 8 to 11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction that may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as observed with the Wyoming bentonite. Results indicate the conditions that should be met with respect to pH control to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1985

By A. M. Gaudin, C. S. Chang

IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.1-4 The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods.5-6 In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba140 to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,4 were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand picked quartz, washed free of stains, were reduced in size to -20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This -200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then' was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn,, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.7 The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74 micron quartz particles, using a surface factor of 1.96,8 is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1952

By T. V. Subrahmanyam, A. P. Rao

The adsorption behavior of chalcopyrite has been studied at different xanthate concentrations and flow rates in a column apparatus with potassium ethyl xanthate as the collector. Based upon the experiment results an equation of the type: 1/F = K3 + m3C + k2/t.Cm2.fm1 is proposed to account for the experimental data. Among copper minerals an early study on chalcocite by Gaudin and Schuman (Taggart, 1951) is well known for its research on the kinetics of the reaction by conventional method of mass balance between the products of reaction and xanthate consumed. The results were interpreted by the concept of ion exchange adsorption. Szeglowski (1977) conducted measurements on the adsorption of potassium ethyl xanthate on copper polarized to various potentials, the adsorption being measured by radio-tracer techniques. The adsorption in the range -1800 to 700 mv was found to be a reversible physical adsorption. The potential range in which the primary electrode process could lead to surface coverage with a minimum number of product layers was evaluated. The adsorption density of xanthate on sulfide surface was found to be related to the concentration of xanthate in solution and concentration of depressants as: [ ]

Jan 1, 1983

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By Paul Soros

Terminal facilities were recently completed at Conneaut, Ohio, on Lake Erie, for the Bessemer and Erie Railroad Co. (a wholly-owned subsidiary of U.S. Steel Corp.) which may become the blue- print for all future coal shipping terminals. Design and engineering of the new facility was by Soros Associates, New York, N. Y. Unlike terminals of conventional design, for example, those at Toledo and Newport News, which load coal directly from the railroad car to the vessel, the new installation passes the coal into temporary storage, loads the vessel from temporary storage and provides alternative reclaiming systems in case of major system failure.

Jan 1, 1966

By R. H. Goodman, C. A. Brown

The development of improved new models of spiral concentrators is reviewed. The mechanics of separation of spiral concentrators are stated, including the effects of operating parameters. Some of the traditional areas of spiral application are described, together with examples of new applications such as treatment of fine alluvials and tailings, separation of liberated minerals at coarse sizes, and fine coal recovery.

Jan 1, 1986

By J. S. UNGER

A LARGE proportion of the coke used is made in the by-product oven from the high-volatile coals mined in the adjacent district. At the beginning it was feared good by-product blast-furnace coke could not be made with our coals. By experimenting with various mixtures of coals, coking time, oven design, and coking temperatures, much has already been accomplished. The results show that a hard, dense coke, not easily broken by handling, can be produced. In its present state it is not all that could be desired, but it is being constantly improved. Such coke has been used alone as the fuel on several of the blast furnaces producing the highest daily production in the Pittsburgh district. Many of the coals in the Pittsburgh district when coked in the by-product oven yield a gas which contains a high percentage of sulfur, which is objection- able for many metallurgical operations. As this fuel is gradually replacing the ideal fuel, natural gas, which is becoming less plentiful, studies are being made of the best methods for purification. Some metallurgists believe sulfur to be a very injurious element in steel. Recent investigations by Government bureaus, scientific bodies and private firms, seem to indicate that a reasonable amount of sulfur may exist in steel without detriment. Without wishing to provoke any metallurgical controversy on the subject of sulfur, the fact remains that the daily purification

Jan 1, 1926

By Y. Zimmels, I. J. Lin, I. Yaniv

The potential application of magnetic and electric separation techniques in beneficiation of fine-particle feeds are reviewed. Special features of these techniques are considered and compared with a view to increased amenability of such feeds to separation in electro- magnetic fields. The following techniques are discussed, with reference to those already developed and in use to-date: - Differential-susceptibility separation (DSF). - High-gradient differential-dielectric separation (HGDDS). - High-gradient magneto-gravimetric separation (HGMGS). In this context the new approach - whereby selectivity of solid- solid separation processes, in wet high-gradient magnetic and electric separation, can be improved - is described, including experimental results from DSF and HGDDS tests.

Jan 1, 1980

By F. S. Knoll

The expanding role of electrostatics as applied to minerals and related fields is covered in this paper. New and existing forms of electrostatic separation are classified into two broad groups: separation of charged particles and separation of neutral particles. The basis for each form of separation is discussed along with particle examples and results obtained.

Jan 1, 1986

By L. A. Roe

Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Fullarton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not? The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized.

Jan 12, 1958

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921