Search Documents

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By Euler De Souza

"Underground operation ventilation energy requirements constitute a significant portion of mine energy consumption (40–50%) and total energy costs (25–40%). In general, mine ventilation systems are energy inefficient; the author has found several systems that operate at efficiencies below 65%. This paper presents how engineering design principles can improve the performance and efficiency of ventilation appliances, resulting in reduced power consumption and operating costs. Case studies demonstrate that, by retrofitting ventilation appliances using proper engineering concepts, systems will operate at efficiencies well above common operating efficiencies, resulting in a drastic reduction in costs and base electrical and energy loads.RÉSUMÉ Les besoins énergétiques nécessaires à l’aérage d’une exploitation souterraine représentent une part considérable de la consommation d’énergie d’une mine (de 40 à 50 %) ainsi que des coûts totaux liés à l’énergie (de 25 à 40 %). De manière générale, les systèmes d’aérage d’une mine sont loin d’être écoénergétiques ; l’auteur a trouvé plusieurs systèmes fonctionnant à des rendements inférieurs à 65 %. Cet article présente les principes de conception technique qui peuvent améliorer la performance et l’efficacité des systèmes d’aérage, entraînant une réduction de la consommation d’électricité et des coûts d’exploitation. Des études de cas montrent qu’en les rénovant à l’aide de concepts techniques adéquats, les systèmes d’aérage fonctionneront à des rendements bien supérieurs aux rendements habituels d’une exploitation. Ces rénovations donneront lieu à une réduction considérable des coûts ainsi que des charges électriques et énergétiques de base.INTRODUCTIONIncreasing electricity supply problems in North America have encouraged an industry-wide evaluation of energy consumption, resulting in a more urgent emphasis on energy-efficient design and operation for all energy-consuming systems. Electricity is the main mode of energy supply and the mining industry is affected by the increasing cost of this commodity (Natural Resources Canada, 2017). Ventilation systems normally operate 24 hours per day, 365 days per year, and account for 25–40% of the total energy costs and 40–50% of the electrical consumption of a mine operation (De Souza, 2013). Ventilation engineers are under ever-increasing pressure to reduce ventilation energy consumption and be cost effective."

Jan 1, 2018

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By Hayel M. El-Naggar, Sherif A. Akl

Although grouted piles have been used for several decades since the idea was proposed in the 1970s, their design is mostly based on experience and unpublished proprietary methods. There is little research on grouting drilled shaft tips and even less on grouting shaft sides. This paper presents the analysis of 4 instrumented pile loads tests on base and shaft grouted piles from different sites in Egypt; with emphasis on one of the tests, to demonstrate the analysis process. The data from the tests are analyzed to model the development of unit side friction (USF) with relative displacement. A numerical model using the finite element software PLAXIS is used to investigate the effect of grouting on the surrounding soil stress state. The paper combines the observations from full scale pile load tests and results from the numerical model to suggest an idealized behavior of side friction development with relative displacement of the grouted part of the shaft. The suggested model considers an envelope of Unit Side Friction (USF) with relative displacement, initially dominated by the grout resistance then at higher relative displacements, the friction with radially pressured soil takes over. The grout provides very high USF values up to a relative displacement of 2mm. Then, the USF drops to a typical pile soil side friction behavior; however, this friction is affected by the contact stress between pile and soil, which significantly increases due to compaction grouting. INTRODUCTION Base and shaft pile grouting has been significantly developing in recent years to accommodate the unfavorable conditions in major projects such as the high loads in high rise building and founding on problematic soil formations. Grouting aims to decrease settlements and increase the capacity of the pile under axial load. The technique is first introduced by Kraft (1974) but gained popularity in the 1980s. Typically there are two types of grouting; compaction, and permeation. Compaction grouting is more common in pile foundations practice, and many researchers have provided case histories of pile load tests on base grouted piles and base and shaft grouted piles (Gouvenot and Gabaix,1975; Stocker, 1983; Ghazali et al., 1988; Fleming, 1993; Kusakabe et al., 1994; Robson and Wahby,1994; Joer and Randolph, 1998; Hamza and Leoni, 1998; Mullins et al. 2000; Littlechild et al., 2000; Suckling and Eager, 2001; Dapp and Mullins, 2002; Ho, 2003; Fu and Zhou, 2003; Brettmann and NeSmith, 2005; Ruiz, 2005; Mullins, 2006; Dapp and Brown, 2010; Beadman et al., 2012; Nguyen et al., 2013; Miller et al., 2013; Sinnreich and Simpson, 2015; Hui and Lin, 2015). Compaction grouting is meant to densify the soil around the pile and below the base rather than permeate this soil and increase its cohesion. Research showed that grouting increases the capacity of the piles by a factor of 2~5. The variation in capacity increase depends on pile type, grouting process, and especially grouting pressure. Although there are many case histories of pile load tests on grouted piles but there is no well-defined agreed-upon method to predict grouted pile capacity as typically done in ungrouted piles. Few lab experiments discussed the shaft grouting effects on the soil especially the compaction grouting. The experiments concluded that the compaction grouting forms a homogeneous layer between the pile and the soil, and a residual effective stress is achieved simultaneously with a significant densification of the soil around the pile with noticeable decreasing in void ratio. (Fattahpour et al., 2015; Wang et al., 2015). Recently, studies used numerical analysis to investigate the behavior of the grouted piles and the changes in the surrounding soil (Chiang et al., 2013). That study presents a simulation of the base pressure grouting with a simple FE model and predicts the reduction of the pile settlement by 10 to 20%. Another numerical study using a complex model conducted by Zhou et al. (2017), pr

Jan 1, 2018

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By Christopher Newman, Zach Agioutantis, Gabriel S. Esterhuizen

"As conventional underground deposits are continuing to be depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. Over the past decade, there has been a global increase in the application of cemented paste backfill (CPB) material as a means of ground support in open stope mining operations. Although CPB has been extensively used within the industry, there are many fundamental factors affecting the design of safe and economical fill structures that are still not well understood. A critical design issue with respect to backfilled stopes is determining the stress state within the fill material as well as the surrounding rock.This paper details the development of a reliable numerical model for the simulation of stress distributions around the excavated stope area, as well as through the backfill material. Through discussions on modeling parameters and output results, one is provided with insights into the mechanisms of stress redistribution allowing for further accuracies in simulating the behavior of the CPB material as well as its interaction with the surrounding rockmass.INTRODUCTION AND BACKGROUNDModern technological innovations with respect to material processing, cementitious composition and chemical additives, and material transportation have provided the mining industry with a ground support material that greatly reduces mine waste costs, while, when used appropriately, increases reserve production and mine stability. As mining operations continue to produce in more complex geologic and geometric conditions, cemented paste backfill (CPB) has become commonly employed within primary-secondary excavation-support sequencing allowing for total extraction of the mining reserve. As shown in Figure 1, primary stopes are initially excavated and then backfilled in a two-staged pour: plug and final pours. The plug (initial pour), is initially placed at the bottom of the stope with a CPB material of heightened cementitious material. While the plug provides a strong foundation on which to build the rest of the CPB structure, it also provides protection against barricade breakthroughs (Li and Aubertin, 2009), as well as providing operations a means of underhand stope-and-fill mining through the use of an artificial sill pillar (Hughes, et al., 2011). Following placement, the plug is allowed to cure to a designated design strength. Upon completion of the plug, a less cementitious “final” pour material is used to backfill the rest of the excavated area."

Jan 1, 2018

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By Stephen Hall

Introduction Marine Autonomous Systems are making rapid progress from their early years as research tools for university departments & government institutes into having a growing number of real-world applications for industry, academia, statutory inspection, data acquisition and defence. Deep sea mining offers a distinct set of challenges that are very well suited to autonomous underwater vehicles (AUVs) and to a lesser extent for autonomous surface vehicles. Deeper, smarter, more capable Global demand for rare earth metals and high-grade ore will inevitably lead to exploitation of deep ocean resources as terrestrial reserves become depleted or remain unavailable for political or environmental reasons. Winning production licenses from the international seabed authority and especially gaining public trust to undertake deep sea mining activities and licenses will depend upon high quality pre-exploitation scientific surveys of the sea floor ecosystem, and subsequent monitoring of the impact of mining activity and remediation work. The actual area covered by the seabed mining operation may be quite small in terms of square kilometres, but still larger than can be patrolled by tethered ‘eyeball’ class Remote Operated Vehicles, so multi-spectral inspection, assessment and monitoring will be more effective when carried out by untethered AUVs. By using seabed recharging stations and data upload points the AUV can stay in situ in the deep ocean, rather than be repeatedly brought back to the surface.

Jan 1, 2018

By M. C. I. Modenesi, J. E. Smith, M. Salvá-Ramírez, G. M. Castro, J. C. Santamarina

Annual metal consumption per capita has increased several orders of magnitude worldwide since the turn of the 19th century, yet grades of terrestrial ores are decreasing as reserves dwindle. Consequently, deep sea metal deposits are gradually transitioning from identified resources to economically viable reserves. Deposits in the Red Sea deeps along the axial trough result from tectonic and local hydrothermal processes. Continental rifting and ocean floor spreading produce fresh oceanic crust; concurrently, seafloor evaporites flow into the spreading zone and form isolated deeps. The deeps are often filled with hot stratified brines maintained by locally discharged fluids during hydrothermal circulation. Metalliferous sediments precipitate from the brines within the deeps. The ongoing multipronged study at KAUST involves: (1) acoustic characterization of the metalliferous accumulations using advanced signal processing techniques that capture the physics of granular materials; (2) comprehensive mineralogical and textural characterization of sampled sediments using SEM, EDS, XRD, XRF, and ICP-OES; (3) multiphysics instruments deployed to measure undisturbed sediment properties in-situ; (4) development of a distributed seafloor observatory for monitoring field operations; (5) innovative concentration and separation technologies; and (6) new strategies for proper tailings disposal purposely conceived for the unique field conditions in the Red Sea deeps.

Jan 1, 2018

By H. X. Yan, J. X. Zhang, F. S. Niu

"The analysis on influencing factors of hydraulic conditions in fine hematite flocculation, such as stirring speed, stirring time and axial distance of particle size and fractal dimension of floc was investigated. Furthermore, response surface methodology(RSM) has been applied according to the Box-Benhnken center-united experimental design principle to optimize parameters of hydraulic conditions as a response index to indicate the fractal dimension of floc. The results show that when the agitation speed is 900r/min, the axial distance is 2.0cm, and the stirring time is 3.0min, the particle size reaches the maximum value of 35.44µm and the fractal dimension is 1.6594. The interaction between the axial distance and the stirring speed is highly significant, but the interaction with the stirring time is not obvious. The experimental data and model predications match well, which indicates that the established model has high accuracy and practicability. INTRODUCTION With the exhaustion of iron ore resources that are easy to be mined and the vigorous demand for iron and steel, the exploitation and utilization of fine-grained embedded iron ore resources have drawn attention from the industry and the government [1~2]. Flocculation flotation is one of the effective methods for separation and recovery of fine granular minerals. In 1975, the method was first applied and succeeded in Tilden Concentrator, USA. Flocculation and desliming became the key technology of the Tilden to raise its annual treatment capacity from 4 million tons to 8 million tons at that time [3 ~ 4]. In 2008, the selective flocculation and desliming-reverse flotation technology was successfully used to treat 2.8 million tons of Qidong iron ore. Under the conditions of 28.36% raw iron grade and 98% grinding fineness -0.038 mm, the ideal index of 62.5% iron concentrate grade and 68% recovery was obtained [5]. Dr Kitchenner of the Royal College of Mining and the Ore Processing Research Group of Wallenstein Laboratory first proposed the use of flocculation to separate minerals. After that, many scholars conducted a great deal of theoretical and practical researches, but mostly they focused on chemical theories, mathematical models and selectivity differences in the flocculation process, while the research on the influence of the pulp flow state on the separation effect in the flocculation process started later [6~9]. The results show that the motion of the agitated flow field has a significant influence on the formation of flocs. The fluid morphology will change with the change of hydraulic conditions. The change of fluid morphology will not only affect the movement behavior of particles, but also change the action of chemical agents on the surface of mineral particles[10~12]."

Jan 1, 2018

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By Bhargav Dhavala, Sristy Raj, Ashok Kumar, Suman Krishna Sit, Adity Ganguly, D. P. Chakraborty

"Tatasteel’s West Bokaro washery#3 is designed to deslime raw coal at 0.5mm; the oversize (+0.5mm) is beneficiated in dense media cyclones (DMC) while the undersize (-0.5mm) is beneficiated in froth flotation (FF) cells. Nearly, 80% of the raw coal feed reports to the DMC circuit consisting of four parallel streams. Presently, the performance of DMCs at washery#3 is interpreted by: (a) comparing the actual plant yield w.r.t the lab predicted yield and (b) misplacement of clean coal to middllings.However, the comparison between actual & lab predicted yield is fallacious given the fact that the lab predicts yield of the borehole sample while the feed received at the plant has different characteristics altogether due to the dilution during mining. To mitigate the said limitations, a quick diagnosis tool using the past data has been developed that will give a prediction of performance of different coal seams in the DMCs, inputs being feed ash to DMCs and stream wise feed specific gravity (coal & magnetite combined).The tool also will help in identifying the root cause on real time basis thereby helping the operator to take necessary corrective actions. The operator can intimate the mining personnel in cases of shale reporting to the feed as a result of dilution during mining. In events of higher standard deviations between the parallel streams w.r.t feed specific gravity, the operator can adjust the parameters accordingly to minimize the yield loss. INTRODUCTION West Bokaro came into existence in 1948, as an independent coal company, managed by M/S Anderson Wright. Tata Steel acquired the Company in 1956 to meet its requirement of metallurgical grade coal for Iron making. Subsequently, in 1976, it was made a division of Tata Steel. In 1974, when coal mines were nationalized, West Bokaro was exempted as it produced coal only for captive consumption of the Steel Works. The first washery of India was set up in West Bokaro. The business objective of the West Bokaro division is to produce clean coal at optimum cost for captive use in the steel plant of Tata Steel at Jamshedpur. The strategy is to reduce ash with minimum loss of yield so that quality of coal improves and yet the cost is beneficial vis-a vis imported coal. The primary product is the metallurgical grade coal for coke ovens, which converts coal into coke for use in the Blast Furnaces."

Jan 1, 2018

By A. Kogelbauer, A. Stadtschnitzer, A. Boehm, F. Schillab

"The paper covers the design and implementation of an industrial dense medium cyclone plant for carbonaceous iron ore, the proving of efficiency as well as the development of a predictive model for plant control. The VA Erzberg GmbH mines about 12 Mio.t of carbonaceous rock ore at the “Steirische Erzberg”. Due to increased demand of the Austrian steel plants, the production of ore concentrate was raised by 30 % up to 3.0 Mio t/a during the last 5 years. One of the projects to realize the increase in capacity at improved concentrate quality was the implementation of a dense medium cyclone plant for the fine size fraction – 8 +1 mm replacing the former dry permanent magnetic drum separators. By physical separation the siderite variety “spateisenstein” (42% Fe) of a density of 3,8 g/cm³ is separated from ankerite (10 – 17% Fe), the second iron bearing carbonate with a density of 3,2 g/cm³, dolomite, calcite and silicate bearing schists. The feasibility of the process was proven by the test results obtained from a test rig, that was constructed and operated in close cooperation between the Chair of Mineral Processing, Montanuniversitaet Leoben and VA Erzberg GmbH. The density separation surpassed the efficiency of magnetic separation clearly shown by •- values. The plant performance tests (capacity 120 t/h) verify the cut densities defined by Tromp T50 -values and the assigned efficiency found in the pilot tests at varied settings of media density, pressure drop, cone angle and apex diameter. The test rig as well as the final process will be presented. In order to create a tool to predict the performance of the DMS in the centrifugal field at various settings for varying feed composition the experimental results from size and density testing are analyzed in a modified way to obtain physically justified, smooth approximations for the performance curves. Models developed on coal washing plants are checked for their validity at increased densities."

Jan 1, 2018