Search Documents

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By Filipe de Menezes Torres, Augusto Pereira de Sa, Itavahn Alves da Silva, Eliana Ferreira Rodrigues, Carlos Antonio da Silva, Varadarajan Seshadri

Top slag eye opening which happens as a result of gas injection is a function of the gas flow rate in addition to other factors such as ladle geometry, porous plug location as well as slag properties. Slag eye opening leads to entrapment of atmospheric nitrogen, oxygen by the steel melt affecting adversely the steel quality. In this work aspects of mixing and eye formation in steel making ladles with inert gas injection have been analyzed through physical and mathematical modeling techniques. Influence of ladle, gas flow rate and distribution and slag properties has been assessed. A correlation for estimating eye opening has been developed. Results from PIV measurements and images of eye opening obtained using a camera have been utilized to validate results from CFD simulation.

Jan 1, 2015

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By J Watson, C Zhang, I Canbulat, C Wei

Coal burst is defined as a dynamic release of energy within the rock or coal mass in underground coalmines that causes violent rock or coal ejection in the vicinity of mine excavations. It poses one of the highest safety and productivity risks in the mining industry as coal bursts have the potential to cause multiple fatalities. As Australian coalmines go deeper, the likelihood of coal burst increases. Thus, it is critical to assess the ground support requirements in coal burst-prone conditions. A previous study conducted by the authors (Wei et al, 2022) reviewed the support capacities of a wide range of ground support elements in laboratory tests. This study aims to examine the role and effects of the ground support elements and systems for Australian underground coalmines to minimise the damage caused by catastrophic dynamic failures (ie coal and rock burst) and enhance the safety of mine workers.

Nov 29, 2022

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By J Aydin Bilgin, Sedat Esen

This paper describes the ideality of some commercial explosives with the help of the detonation theory and detonation velocity measurement. Ideality of an explosive can be determined by comparing experimentally measured and ideal detonation velocities. A measured detonation velocity at a certain charge diameter markedly lower than the ideal value indicates incomplete reaction and thus non-ideal detonation. Since it is shown that commercial explosives exhibit non-ideal behavior, two-dimensional detonation theory should be used to evaluate the performance of explosives. This theory enables to compute the detonation properties of explosives (detonation velocity, detonation pressure, etc.) as a function of charge diameter and confinement. The use of the one-dimensional detonation theory to compute the detonation properties for commercial explosives has an error associated with it as these calculated properties are independent of charge diameter and confinement. It assumes that shock front is planar. Hence, it is incapable of assessing the ideality of the explosives due to its assumptions. Shock front in real situation is curved in shape but not planar as in one-dimensional detonation theory. In this paper, the non-ideal behavior of some commercial explosives is modeled using EXRINT code based on the steady-state two-dimensional detonation theory firstly. Then the degree of ideality of each explosive found from the code is checked using detonation velocity test results conducted at a quarry. It has been shown that idealities of the tested explosives determined by the code agree well with the field detonation velocity test results.

Jan 1, 1999

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By D. W. McGlashan

[Comideha;tion o 4 chyakd- chem and aLtuctund phopetttiu o auRdide nm&, The in~o/uncction gained h ;to be uned ;to iM;tmph& ( I! dnukey bho hen mind-aundacu , ( 2 ) modidicakio~n 06 ;the minmd n~tdacu, and (3) eac;tiom at ;the mind adac fnom ;thu e baic din oipfina, concep;tc, wLth hegattd ;to .the changen kha;t awtgacu undehgu, heac;tiom kha;t might take place, ,the geom&y 04 ;the inkmduce, ;the nkde 04 diddmenk &om and iom in ;the intmdace, and okhm phyaicd and chemicd pttopemXu od an intmdace mun;t be developed, weighed and appfied. The au/tho~ ded wah thue concep;tud connidmatiom @om which hypokhuu me n& ko denchibe khe envhomenkd-ivttadaciae hela;tiomhipa doh nevmd nddide minettah, The ch&enge and moltivation in khe hu eattch h in a henhe a deattch doh baic dad and helcctiomkipa needed doh accompfi he&.] INTRODUCTION Qualitative and quantitative explanation of particulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occur- ring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc. on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental- interfacial relationships for sulfide minerals.

Jan 1, 1968

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By M Ridd

The Pasminco Century Mine (PCML) is located 250 kilometres north-north-west of Mt Isa in Queensland. As one of the worldÆs largest zinc mines, PCML comprises mining and milling operations at Lawn Hill, concentrate filtering and shipping facilities at Karumba in the Gulf of Carpentaria, and a 304 km slurry pipeline connecting the two operations.Mineralisation at Century occurs in the upper part of the Lawn Hill formation and is comprised of siltstones, shale and sandstone. Pyrite occurs immediately above the mineralised sequence, and throughout the footwall carbonaceous shale forming the lower proportion of the deposit. Zinc predominantly occurs as sphalerite (ZnS) and lead as galena (PbS). These sulfides are very fine-grained and may oxidise rapidly upon exposure. The pyrite, sphalerite and galena are the main potential sources of acid rock drainage (ARD) or heavy metal leachate at the mine site.To minimise the generation of ARD in the waste rock dumps, they are constructed in a specific manner and waste rock is classified into the following three classes based on competence and acid forming/consuming capabilities:Class 1: Competent rock, non-acid forming or acid-consuming material. Class 2: Non-competent, non-acid forming or acid-consuming material. Class 3: Acid-forming material. The generalised Waste Rock Dump Design for current operations comprises an outer zone of Class 1 material and inner zone with Class 2 and 3 material. Limestone is the Class 1 material used for both its structural support and acid neutralising capacity. Reserves of limestone at the mine site are limited. Net acid generation (NAG) tests confirm that a mix of limestone and shales can be net acid consuming.Field based and laboratory based trials have been established at PCML to quantify blending levels of limestone and shale that will produce leachates both neutral in pH and low in metal/salt concentrations. This paper will discuss the first six months results (of a two-year sampling program) from the trials.

Jan 1, 2004

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By A. Jeffkins

Visibility is restricted when operating load haul dump vehicles resulting in a number of serious accidents in the Ontario Mining Industry. One of the leading causes of these accidents is the inability of the equipment operator to see clearly people, objects or hazards around the machine. Previous line of sight testing by the research team found specific machine characteristics were responsible for blind spots and impaired visibility. In order to identify feasible design modifications a computer simulation program, Classic JACK 3.1, was utilized. Program features include human factors analysis, which allows evaluation of line of sight and operator posture in order to decrease risk of musculoskeletal injury. Research within the virtual computer environment consisted of a Visibility Audit and a Target Audit in order to quantitatively determine how certain components of the LHD design affected the line of sight around the vehicle. Results indicate that modifying the LHD light brackets, engine profile, cab posts and other components will enhance visibility. The addition of cameras located on the front and rear of the vehicle were able to enhance the operator?s sight lines to previously obstructed areas. Modifications to seat height and the operators orientation both improved sightlines and decreased risk factors associated with back and neck musculoskeletal disorders.

May 1, 2003

By K Mayank, A N. Mainza, I Govender, M Narasimha, A Mittal

In mineral processing industries grinding is the most energy-consuming process. A tumbling mill is an essential grinding equipment widely used for particle size reduction. Power consumption, impact forces and trajectory paths are critical parameters for characterising a tumbling mill to determine grinding efficiency. The effect of lifters and mill speed plays a vital role in such parameters. However, most of the studies ignore the impact of the lifter and do not investigate the effect of slurry dynamics on charge motion. The focus of the present work is to prepare a computational model that can accurately predict the complex multi-phase dynamics of charge particles, air and slurry inside the mill using a model that couples computational fluid dynamics (CFD) and the discrete element method (DEM). The details of impact forces with lifter profiles and mill speed variations will be refined even further using the CFD-DEM coupling approach. The slurry-air free surface is modelled using the volume of fluid (VOF) method, and the charge motion is modelled using the DEM. The phases are coupled using the interface momentum exchange between the charge and the fluid slurry. The coupled model is validated against experimental results from the positron-emitting particle tracking (PEPT) data. The validated model compares the effect of slurry content on charge dynamics with the dry DEM model. The presence of slurry is observed to dampen the tangential and shear contact forces.

Aug 24, 2022

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016