Search Documents

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By G Hancock, J Lowry, W D. Erskine, D Jones, T Coulthard, M J. Saynor, P Lu

An 8 ha trial landform was constructed in late 2009 at the Ranger Uranium Mine, located 250 km east of Darwin in the wet-dry monsoonal tropics of northern Australia. The objective of the trial, which comprises two surface cover types on a uniform two per cent slope, is to provide long-term data to guide the development by Energy Resources of Australia Ltd (ERA) of its landform closure strategy. The scope of the work program for the landform includes many aspects; however, this paper is focusing on run-off and erosion rates. The run-off and erosion rates are used to assess the long-term geomorphic stability by comparing measured with modelled export rates from a landform evolution model.Monitoring of wet season run-off is undertaken collaboratively by the Environmental Research Institute of the Supervising Scientist (ERISS) and ERA, on four purpose-instrumented 30 m by 30 m erosion plots. Continuous measurements are made in rectangular broad crested (RBC) flumes located at the outflow of each plot, of water level, turbidity (a surrogate for fine suspended sediment) and electrical conductivity (EC) (a surrogate for solutes). Each plot has a tipping bucket pluviometer located near the RBC flume. Bed load is collected monthly.This paper reports the findings of rainfall and bed load from the first two wet seasons (2009 - 2010 and 2010 - 2011) following construction. The field measured loads will be compared with the predictions made by the Cellular Automaton Evolutionary Slope and River (CAESAR) landform evolution model. Initial results indicate that predicted rates of sediment export from the CAESAR model are similar to measured export rates. This provides confidence in the capability of the model to predict stability of the future rehabilitated mine area, especially during the critical initial years following construction. CITATION:Saynor, M J, Lowry, J, Erskine, W D, Coulthard, T, Hancock, G, Jones, D and Lu, P, 2012. Assessing erosion and run-off performance of a trial rehabilitated mining landform, in Proceedings Life-of-Mine 2012 , pp 123-132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Denise Clarke

Homeland Security Qualifications (HSQ) personnel were instrumental in developing the UK’s suite of Explosive Substances and Articles (ESA) National Occupational Standards (NOS) (also known as "competences") on behalf of the Standards Setting Body for Explosives, Munitions and Search Occupations (SSB for EMSO).

Jan 1, 2013

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Takuji Yamamoto

High-speed TBM excavation requires rapid ground assessment ahead of excavation, particularly in complex grounds. The Tunnel Reflector Tracing technology (TRT) developed by authors, uses seismic reflections to produce volumetric images of ground anomalies. To further minimize interruption in the TBM excavation the authors modified surveying technique switching from cable (wired) to radio (wireless) data acquisition system. This paper presents the outline of the Wireless TRT system, and compares the results for the wired and the wireless surveys. The comparison shows that the wireless system offers high precision data, is more efficient and economical and significantly less intrusive in tunneling operations.

By R. J. Gochin, G. D. Schena, R. Spencer

The impact of a mineral project in a developing country is evaluated in the broad context of its economy using input-output models. Minimum economic theory is used to develop simple numerical models. Sets of technical coefficients are exploited in the development of linear models of the productive element of an economy. The analysis allows assessment of the overall economic consequences of a mineral development in which issues broader in scope than financial objectives need to be incorporated in the evaluation. In part 1, the framework for the development of the input-output model is presented. The model is refined to incorporate country-specific behaviour. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy-wide effects associated with a new project in the mineral sector of a developing country. The relevance of the models is illustrated using an example from Namibia

Sep 1, 1991

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Heather Dougherty, Ted Klemetti, DYKE MARK VAN, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By P A. Dowd

This paper describes an integrated approach to the evaluation of ore loss and ore dilution via geostatistical simulation of in situ geology and grade characteristics, simulation of blasting mechanisms and simulation of loading from a blast muck pile. The approach is demonstrated on a case study. The sequential Gaussian method is used to simulate in situ bench grades on the scale of the smallest selectable volume within a blast muck pile. The simulated grades of these component volumes are interpreted as the reality that would be available with exhaustive sampling. The simulated bench is subjected to a blast simulator, based on the SCRAMBLE model, which effectively moves each of the component model volumes to its final resting place in the blast muck pile. Ore/waste delineation and selective loading processes are applied to the simulated muck pile to determine the degree of selectivity that can be achieved by various sizes of loader and types of loading and to quantify ore dilution and ore loss. An in situ model representing the reality of knowing only the data and information that are available from specific grade control drilling and sampling grids is obtained by sampling the geostatistically simulated model on a specified grid. The volumes comprising the in situ model are then populated by estimates based only on the data and from the specified grade control drilling and sampling grids. Different drilling and sampling grids are used to generate different models, each reflecting the levels of data and information available. Selectivity is assessed as a function of the drilling and sampling grids as well as the size and type of loader. Performance is assessed against the ideal selectivity that could be achieved on the perfect knowledge model comprising the simulated values of each component volume. Costs, prices and financial criteria enable an optimal selection of the grade control drilling grid, size of loader, type of loading and blast design.

Jan 1, 2004

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

By Gregory M. Rumbaugh, Christopher Mark

"The proliferation of unconventional gas well development in the Northern Appalachian coalfields has raised a number of mine safety concerns. Unconventional wells, which extract gas from deep shale formations, are characterized by gas volumes and pressures that are significantly higher than those observed at many conventional wells. The gas is composed largely of methane as well as other hydrocarbons. Hundreds of planned and actively producing wells penetrate protective coal pillars or barriers within active mine boundaries, including chain pillars located between longwall panels. Gas released from a well damaged by mining-induced ground movements could pose a risk to miners by flowing into the mine atmosphere. The mining-induced ground movements that may cause well damage include conventional subsidence, non-conventional subsidence (e.g., bedding plane slip), pillar failure, and floor instability. This paper describes the known risk factors for each of the four failure mechanisms. It includes a framework that can guide the risk assessment process when mining takes place near gas or oil wells.INTRODUCTIONSouthwestern Pennsylvania has served for centuries as a producer of coal, oil, and natural gas. Coal mines were first developed in the Pittsburgh Coal Seam in the 1760s, with the first recorded mine in 1761 being the Fort Pitt Mine (Edmunds, 2002). Natural gas was introduced to the region when the Haymaker Well in Murrysville, Pennsylvania experienced a blowout on November 3, 1878. Although it was originally drilled prospecting for oil, it produced an estimated 30 million cubic feet per day of natural gas. Without well controls or pipeline infrastructure in place, it burst into flames and lit the night sky for over a year. Soon after, the Penn Fuel Company continued development of the Murrysville gas field and is credited with making Pittsburgh, Pennsylvania the first major city in the U.S. to have natural gas supplied for home and industrial uses. “Natural gas is king in Pittsburgh,” proclaimed an October 18, 1885, article in the New York Times headlined “Value of Natural Gas, Its Use Clarifies the Atmosphere at Pittsburgh” (AOGHS, 2018). By the early 1900s, coal, oil, and natural gas production had reached the southern extents of Pennsylvania in Greene County. The county had first produced oil in 1886, and shortly after began producing natural gas in 1890. By 1906, over 1,300 wells had been drilled (Stone and Clapp, 1906)."

Jan 1, 2019

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

Jan 1, 2006

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011