Search Documents

By Feng Cai

"As a new method to support gate roadways, rock bolting has been widely used in the big coal enterprises for its superiority. The disturbed stress field of surrounding rock and anchor pre-stress field were divided into 3 areas in consideration of s1, s3. The surrounding rock failure form and characteristic were analyzed in combination with parameter f, the failure mechanism was explained using the slip line theory, furthermore, the rock bolting mechanism and its arrangement were studied. After roadway excavation, the tensile stress area appeared at the surface of the surrounding rock. The failure type changes from shallow tension-shear form into deep compression-shear form and the failure shape is an “incense burner”, surrounding by high risk failure area in butterfly shape. The maximum principle stress in roof appears discontinuous distribution because of layers separation. The failure type of surrounding rock is intensity-stress environment-weak plane control model. The internal reason of roadway macroscopic failure is the displacement between the surface plastic area and the deep elastic region along the tangential direction of slip line. In condition of rock bolt support, there is one-way tensile stress area in small range at the surface of surrounding rock, inside is the bidirectional compressive zone in uniform distribution form, stress environment is improved by the superposition of anchor pre-stress and disturbed stress field, anchor rock bolt arrangement and pre-tightening force distribution is decided according to the distribution of f parameter. Finally, supporting method and parameter reasonability was proved by the roadway deformation monitoring, damage depth drilling peep test in the 8101 transportation roadway in a mine.Introduction The stability of roadway support is very important to the safety and sustainable development of coal mine. In recent years, the focus of China's coal mining industry began to move to West China, the thick-extra thick coal seam is developed in the West. The latest technology and equipment have been put in to service, the occurrence condition of thick coal seam and the increasing of productivity lead to the cross section of the roadway increasing continually, hence, it is more difficult to control the surrounding rock. At present, the most common way to support the roadway is rock bolt (cable) support (Wang 2007); Scholars have been deeply studied on the mechanism of rock bolt. It is reported (Wang et al 2012, Gao 2007, Zhang and Yuan 2006) that the influence of rock bolt on physical and mechanical parameters of coal and rock mass in the anchorage zone, It is believed that the rock bolt can improve the peak strength of surrounding rock, especially the post peak strength, and the failure mode of rock mass under the rock bolt support is analyzed. It is reported (Wang et al 2014, Xiao et al 2013, Li et al 2007, Yan et al 2012), according to different geological conditions, the failure mechanism of surrounding rock and supporting technology of the whole coal roadway were studied. Focus on the failure mechanism of roadway surrounding rock, different forms of high strength support methods were proposed, which achieved good results. It is reported (Wang et al 2012a, Zhang et al 2011, Wang et al 2012b, Kang et al 2010, Zhang et al 2010, Kang et al 2007) that the supporting mechanism of pre-stressed anchor was analyzed from the point of the distribution of the maximum principal stress in the pre-stressed anchor field, and the influence of the rock bolt support parameters and surrounding rock characteristics on the supporting effects were studied. Based on the latest research results, this paper analyzed the failure mechanism of surrounding rock of coal roadway, proposed the high strength anchor net cable combined supporting technology based on the feature of stress zoning distribution of surrounding rock, to provide reference for the coal roadway rock bolt (cable) support technology."

Jan 1, 2017

By C. Roos

"Nearly every input to a mine plan is based on an estimate. The estimates may be from sample data, historical information, models, or personal opinion, but in all cases, these values are simply expected values (means). In real life, we do not get to iterate the exact conditions at our mining operation many times to ensure that that average value is attained. The expected value also tells us nothing about the spread of values that that input might take on. The result is a significant amount of unquantified uncertainty in our mine plans. Unfortunately, it is often too expensive or time consuming to update planning processes and software. This paper presents a proof of concept spreadsheet scheduling tool that can be utilized to incorporate many geologic realizations (simulated models) into the mine scheduling process. While this POC is not intended to be a detailed model of uncertainty, it is to show that there are stepping stones available for mine planners to begin to embrace uncertainty and produce more achievable plans without requiring a significant change in their planning process. INTRODUCTION Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years, however many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize and even embrace the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process. Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple ore body realizations to provide a thorough unbiased “picture” of the geologic uncertainty but most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter. Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this paper presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid to long-term mine plans while continuously monitoring the uncertainty in the results. The author hopes that by demonstrating the usefulness of such a system that mining companies will encourage engineers, geologists, and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 1, 2017

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By V. K. Srivastava, T. Gupta, T. Ghosh

"In recent years, the demand for rare earth elements (REEs) has grown due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources, with coal and coal byproducts as possibilities. Coals from certain parts of the world can be rich in REEs and can approach a total concentration of 1,000 ppm. Two Alaskan coal samples, from Healy and Wishbone Hill, were investigated for the effects of density and particle size on REE concentrations for three selected size fractions, and flotation tests were conducted on finer fractions. Additionally, bottom ash and fly ash samples from a power plant were examined for their REE concentrations. The results show that the upgrade potential for REEs on an ash basis from a whole-coal basis ranges from 2:1 for the Wishbone Hill samples to 4:1 for the Healy coal samples. Flotations of the finer fractions of the two coal samples, conducted under similar conditions, revealed higher concentrations of REEs in the tailings. Both coal samples had comparatively higher contents of light-group rare earth elements (LREEs) than heavy-group rare earth elements (HREEs). REE content trends for the power-plant products on an ash basis indicate that fly ash has slightly higher concentrations of both LREEs and HREEs than bottom ash. IntroductionRare earth elements (REEs), also known as rare earth metals, and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in the manufacture of wind turbines and hybrid cars. Europium, terbium and yttrium are used in devices that have visual displays such as computer screens and laptops (Haxel, Hedrick and Greta, 2002; Bunzli, 2013). REEs pose fewer environmental problems of disposal and recycling than their conventional heavy metal counterparts (Haxel, Hedrick and Greta, 2002). They are key materials for radar systems, avionics, modern national defense and satellites (Cammarata and Sieradzki, 1994; Hedrick, 2010; Martin, 2010; Szumigala and Werdon, 2011; Cordier, 2011; Bunzli, 2013). REEs are often classified into light-group rare earth elements (LREEs) and heavy-group rare earth elements (HREEs). This classification is primarily based on the electronic configuration in the outermost shell. LREEs, ranging from lanthanum to gadolinium, have a single or no spinning electron in the outermost 4f shell while HREEs, ranging from terbium to lutetium, have paired electrons in the 4f shell. This difference in electronic configuration is responsible for the differences in physical and chemical properties of REEs."

Jan 1, 2017

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

By M. Hepokoski, M. Klein, L. Yan

"NIOSH research has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives (RAs). These high temperature and humidity levels inside an RA may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics to create detailed thermal simulation models of RAs with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine RA. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 95°F apparent temperature limit for RAs is reasonable. The results indicated that the 95°F apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicated that the body core temperature did not reach dangerous levels even at an apparent temperature of 130°F. However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were increased, the water provided in an RA would have to be increased to offset moisture loss. INTRODUCTION The purpose of this effort was to predict a miner’s core temperature and moisture loss (sweating and respiration) in environments that are likely to be encountered in a coal mine refuge alternative (RA). A range of temperatures and relative humidity were studied to determine whether the current 95°F Steadman apparent temperature (AT) limit and 2.25 quart/day water requirements for RAs as mandated by the Mine Safety and Health Administration (MSHA) are reasonable [1, 2]. The effects of metabolic heat rate (activity level), miner size (height and weight), and pose (sitting or lying) on core temperature and moisture loss were also studied. MODEL DESCRIPTION TAITherm thermal modeling software (ThermoAnalytics, Inc.) was used to simulate humans in RA-like environments within a range of temperature and relative humidity combinations. The TAITherm Human Thermal Model (HTM) predicts the dynamic thermal response of the simulated miners while accounting for clothing, human tissue thermal properties, and active thermoregulation. The following sections describe the HTM in more detail, the thermal model setup for this analysis, and core temperature and moisture loss metrics found in published literature. Human Thermal Model Overview The TAITherm human thermal model was used to simulate the heat generated by the shelter occupants, and to predict the miners’ skin and core temperatures along with their sweat evaporation rates. The thermoregulation model simulates the process by which the body attempts to maintain a constant core temperature by considering the effects of shivering, sweating, and changes in skin blood flow. This model calculates surface and deep tissue temperatures within the human body as described by a surface mesh."

Jan 1, 2017

By C. Newman, N. Schaefer

"INTRODUCTION As underground mining continues to operate at deeper depths and in more complex geologic and geometric conditions, there has been an increased demand for higher design standards in ground control safety and stability within the mining industry. Over the past 20 years, NIOSH has developed, validated, and distributed a number of free software packages (ALPS, ARMPS, AMSS, ARBS, etc.) for the safe design of underground coal mines with respect to ground control. While these programs were initially developed on a, “stand alone model,” where all program data resides on an individual or workgroup computer, modern day web applications have begun to migrate toward a, “multiple-tier model,” allowing multiple users to access an application through an Internet connection. webGroundControl provides users with access to NIOSH ground control design software (ARBS, ALPS, and ARMPS) utilizing a web-based three-tier architecture allowing users to easily access ground control designs, perform on-demand calculations, and provide online collaboration between operational personnel and engineers through a web server. Given advancements in cloud computing as well as the expansion of Internet connectivity on the surface and underground, webGroundControl users will be able to access the applications anywhere (where permissible) at any time. As web-based computing technologies continue to advance and cloud computing gains popularity and momentum, there is an industry need to develop Internet based applications for mine and ground control design (Barczak et al., 2016). The purpose of this paper is to introduce and familiarize those in the mining industry with the basic framework and, more specifically, the user-interface of the webGroundControl application. It is expected that the mining industry will rapidly embrace this new product and webGroundControl will be a new paradigm for mining engineering computer applications. APPLICATION ARCHITECTURE With the advent of cloud computing, web-based applications have become more popular with their adoption of multiple-tier, or n-tier, architecture containing independently operating tiers. The three-tier application architecture utilized in webGroundControl (as outlined in Agioutantis and Newman, 2016) contains a Presentation Tier (Web Server), Logic Tier (Logic/Application Server), and Data Tier (Data Server) as shown in Figure 1. While tiers have the ability to be deployed across and operating on multiple servers, webGroundControl is currently being deployed on a single server located on a university desktop computer. The separation of the application into a series of tiers greatly increases the maintainability and scalability allowing for the adoption of new technologies that can be applied to a single tier without redesigning the software package. The Presentation Tier maintains the user interface translating client requests (through a web server) and displaying results (through a web browser). The Presentation Tier allows for on-demand access from multiple users and compatibility with a variety of personal computers, Smartphones, tablets, etc. on different operating systems. The Presentation Tier has been developed with respect to the HTML and JavaScript languages. Through the utilization of CSS, a coding language which describes the style of an HTML document, the webGroundControl display is able to spontaneously adapt to any browser and any screen. The development of the Presentation Tier will be discussed in more detail in subsequent sections of this paper."

Jan 1, 2017

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By K. D. Luxbacher, J. T. Davis

"A wind tunnel was designed to examine air flow, heat transfer and layering near an active fire at a working face. This tunnel simulates an active entry in an underground coal mine including an attached cross-cut of similar dimensions. A steel rectangular duct 1 ft. (0.305 m) tall, 3 ft. (0.914 m) wide and 10 ft. (3.05 m) long composes the main body of the tunnel and represents a mine entry. Air flow is generated by an exhausting centrifugal fan attached to one end of the crosscut. This fan was sized to supply air velocities based on Froude scaling. A 6 in. (15.25 cm) propane burner is used to simulate fires of various heat release rates at the working face. Thermocouples are used to map heat layering in the tunnel. Ports are installed for the introduction of tracer gases into and from sampling the system. Barometric, differential pressure, and temperature sensors are also included to monitor environmental conditions. Details about the design and testing of the system are presented including an overview of how the tunnel was scaled to accurately represent fire and flow phenomena. Finally, the proposed use of the tunnel for better understanding of mine fire phenomena and prevention is given. INTRODUCTION Fires in underground mines have been a concern since the dawn of mining. While technological advancements, regulations and best practices have improved both fire detection and firefighting techniques, mine fires continue to represent high risk events. From 2006 through 2015, fires accounted for 1.06% of fatalities in underground coal mines and 0.85 percent of fatalities in all underground mines in the United States (U.S. Department of Labor, 2006 to 2015). In addition to the risk of loss of life, mine fires can cause millions of dollars in equipment damages and lost production revenue. Extensive research has been conducted on how fires occur and spread in underground mines. In addition to testing conducted by government agencies such as the Mine Safety and Health Administration (MSHA) and the National Institute for Safety and Health (NIOSH) (e.g.(Liming, 2006), researchers like Verakis and Dalzell (Verakis, 1988) and Lowndes, et. al. (Lowndes, 2004) have furthered this field by studying ignitions and propagation of conveyor belt fires. While the studies of belt fires in mines are extensive, studies focused on fires at the working face are few in number. The particularly confined space and limited access to a working face, coupled with less robust, temporary ventilation controls create a unique environment that warrants special attention. Separate from studies on mine fires, the use of tracer gases to characterize flow patterns in normal mining ventilation is well established. In 1982, Timko and Thimons (Timko, 1982) outlined current and future applications of sulfur hexafluoride (SF6). However, little experimentation has been conducted to study specifically how tracer gases might be used to evaluate active mine fires and the fires’ effect on the surrounding mine environment (e.g.(Lindsay, 2014). In order to better understand the dynamics of smoke layering from a fire in an enclosed space, a small-scale apparatus was designed to map smoke layering and to examine other aspects of fire behavior at a working face. In addition to studying smoke flow around an active fire, experiments will be conducted using tracer gases in order to determine how they might be used to evaluate an underground fire."

Jan 1, 2017

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017

By Gustavo A. Aristizábal-H, Oscar J. Restrepo-B, J. Alejandro Delgado-J

"In Antioquia region of Colombia – South America most of extractive activity is developed as artisanal and small-scale level, exploiting different types of minerals resources but predominantly gold. This is not only an ancestral livelihood of hundreds of families in this region, but also their unique way of subsistence. However, that situation has not had a positive effect in the sustainable development of this territory because of several unsustainability factors mainly related to mercury use for gold extraction, the incorrect management of tailings and the informal way in which miners perform their activity. In 2010 Antioquia was the place with the highest contamination by mercury in the world with serious effects in ecosystems and health of habitants of this region (Veiga 2010) This paper presents a Socio-Technical Model focused on strengthening capabilities and social capital of artisanal and small-scale miners and its surrounding communities in Antioquia region. This is based on processes of evaluation, design and implementation of appropriate technologies to obtain “clean minerals” without using mercury and with a right management of tailings. In gold extraction it is about gravitational methods of concentration, which take advantage of high density of this element. These methods not only are cleaner but more profitable for miners. Notwithstanding its technical origins, the current model proposes a holistic framework that manages the elimination of mercury in mining not only as a technology transfer matter. Thus, more than formalization the strengthening process seeks to promote a business vision in miners and to develop productive chains in surrounding communities, this means to improve the skills of artisanal and small-scale miners to organize in a corporative way and to help surrounding communities to provide support and supply services to mining and even to other companies. Besides, the articulation with local institutions drives to reinforce their functions of control and accompaniment. In shorthand, this effort aims to empower local institutions, miners and surrounding communities in such a way they are able to face together their own development challenges in a sustainable way."

Jan 1, 2017

By N. K. Dumakor-Dupey, K. J. Bansah

"We made site visits to determine potential environmental issues caused by artisanal and small-scale mining (ASM) in the Tarkwa Mining Area (TMA) of Ghana. Activities of the diggers were observed to degrade vegetation, land and water. Improper handling of mercury was also identified as a major threat to people and ecosystem. Large abandoned pits and trenches posed fall traps to farmers, hunters and wildlife. We argue that lack of adequate monitoring and regulatory enforcement by Ghanaian authorities, together with inappropriate mining processes, probably due to lack of technical expertise are contributing factors to the environmental issues of artisanal and small-scale mining in the TMA. INTRODUCTION Environmental degradation caused by artisanal and small-scale mining (ASM) has been a major concern to many people and governments around the world. ASM is often associated with health, safety and environmental issues in communities where it is practiced (Kitula, 2006; Asiedu, 2013; Sousa et al., 2010). Some of the environmental issues that have been reported include land degradation, mercury contamination, cyanide release, and pollution of rivers/streams. These issues have been attributed to improper mining methods, inefficient technology, lack of technical training and environmental awareness, and lack of regulatory enforcement (Serfor-Armah et al., 2005; Bansah et al., 2016a; Hentschel et al., 2002). In Ghana, ASM typically occurs in rural communities, providing jobs to many people and contributing towards socioeconomic growth of the country (Banchirigah & Hilson, 2010; Bansah et al., 2016b; Osei-Kojo & Andrews, 2016). As a result of the environmental issues, many people have called on government to develop drastic measures to control ASM operations. It is in this regard that this paper examines potential environmental issues caused by ASM in the Tarkwa Mining Area in Ghana, and suggests mitigation measures to ensure environmental sustainability. ASM in the area comprises of registered (licensed) and unregistered (unlicensed) operations that adopt surface or underground mining methods to exploit gold-bearing materials. Surface operations typically involve clearing of vegetation, removal of overburden, excavation of mineral deposit, washing/grinding of excavated gravels and processing with mercury. Except grinding, washing and mercury recovery, underground operations are conducted below ground with limited impact on the surface. Alluvial mining is also commonly practiced in streams and along river banks. These activities can have devastating impact on biodiversity of the ecosystem. To achieve the objective for this study, field visits were made to ASM sites to observe operations and interact with diggers. Visits were also made to host communities of ASM and government officials to obtain their perspectives on ASM in relation to environmental impact. The study area (Tarkwa Mining Area) is located in the Western Region of Ghana (see Figure 1). It is endowed with natural resources such as gold and manganese. Hence, mining is the major economic activity in the area. ASM is widespread, with 15 registered operations and several unregistered mines. The environmental issues observed in the study have been grouped into three main categories: vegetation and land depletion; water quality and pollution issues; and mercury contamination issues."

Jan 1, 2017

By T. Gupta, T. Ghosh

"Rare Earth Elements (REEs) and their compounds are essential for numerous modern high tech applications such as renewable energy technologies, catalysts and defense applications. The destabilization of REE pricing owing to the global demand and supply deficit has forced many countries to re-evaluate the possibility of indigenous production of REEs. Cost effective and eco-friendly opportunities are being widely explored for extraction of REEs from non-conventional mineral sources such as coal and coal byproducts to stabilize the supply chain. Coal from Central Alaska (Healy Coal Mine) and Southern Alaska-Cook Inlet (Wishbone Hill) province have been found to possess elevated REE concentrations as compared to average world coal estimates. The objective of the study is to enrich the REEs in the fine size fraction (-75 Microns) from Healy and Wishbone Hill by froth flotation technique. A Box-Behnken design was applied for modeling and optimization of some operating variables on the flotation to maximize REE enrichment. The variables studies were frother dosage, pulp density (% Solids) and collector dosage. Experiments were carried out using a statistical design and the main and interaction effects on response variable was evaluated by analyzing 3D response surfaces. Based on the experimental results the optimum flotation conditions for maximum REE enrichment in the froth fraction was obtained at 4.2% Solids and 32.7 ppm of frother dosage for Healy coal sample and 10% Solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic equation for modelling and optimizing the response variable is found to be independent of collector dosage for both the coal samples. INTRODUCTION Alaskan coal deposits are distributed in three major coal provinces and are in Cretaceous and Tertiary rocks. The climate, vegetation type and sedimentation process has attributed to low sulfur content (averaging 0.3 percent) in Alaskan coals compared to other coal deposits found across the globe. In Central Alaska-Nenana and Southern Alaska-Cook Inlet coal province coal resources are contained in Tertiary rocks while bulk of the Coal resource in North Slope coal province is contained in Cretaceous and Tertiary coal bearing rocks [1]. Coals from Central Alaska- Nenana (Healy) and Southern Alaska-Cook Inlet province (Wishbone Hill) have been found to possess elevated concentrations of critical REEs as compared to the amounts present in world coals (Figure 1). The Wishbone Hill deposit is considered a relatively small deposit, with about 14 million tons of identified reserves, compared to Healy which has over 500 million tons identified [2]. The REE concentrations up to 286 ppm and 524 ppm on ash basis have been reported by Gupta et al. in 2016 with elevated concentrations Ce, La, Y and Nd which are expressed to be of critical importance by US Department of Energy. Accordingly, the two coal samples possess the potential to be used as a REE resource in the near future under favorable socio-economic and geo-political scenarios. [3, 4]"

Jan 1, 2017

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

By Z. Jin, D. DePaoli, P. Zhang

"Phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and fine in size, with more than 50 percent having particle size smaller than 2 µm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.IntroductionFlorida phosphate ore, or “matrix,” as it is called locally, contains three different mineral groups that have to be separated from each other: (1) phosphate minerals, (2) clay minerals and (3) quartz, or sand. As mined, the phosphate and sand particles are embedded in compacted mud, or clay-balls. Before separation can begin, all of the particles must be liberated from the matrix of mud. The very first unit operation in the beneficiation process is to disaggregate the various particles. This actually starts while the matrix is flowing through the multimile pipeline from the mine to the beneficiation plant. While in the pipeline, the matrix is exposed to shear forces as it passes through the various centrifugal pumps along the pipeline. These intense shear forces cause a significant percentage of the sand and phosphate particles to be liberated from the clay-balls by the time they arrive at the plant. Once they reach the plant, the first goal is to finish disaggregating the clay, and follow that by making a size separation at 1 mm. This processing is conducted in the washer, consisting of a large rotating trammel screen and a few stages of log washer, screens and hydrocyclones. In all of the currently operating beneficiation plants, the washer is a large structure that receives the matrix, screens it and then discharges a pebble phosphate product sized larger than 1.0 mm and a slurry of liberated clay, sand and phosphate particles that are smaller than 1.0 mm."

Jan 1, 2017

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Zhe Liu, Liping Xiao, Jichi Bai, Xuefei Luan

"In order to study the removal efficiency of Cu2+ from acid mine drainage by prepared bentonite-steel slag composite particles, adsorption experiment was carried out. The composite particles were characterized by X-ray Diffraction analysis technique (XRD), Scanning Electron Microscopy (SEM) and Fourier Transform Infrared spectrometer (FTIR). The results show that: the composite particles can release alkali to neutralize the acid of acid mine drainage; the adsorption and chemical precipitation of Cu2+ occurred in the whole reaction process; the removal amount of composite particles on Cu2+ was 9.88 mg/g when the reaction reached equilibrium; the FTIR spectra revealed the existence of surface complexation; the SEM micrographs suggested that the composite particles would continue to adsorb and coagulate Cu2+ after the composite particles surface adsorbing Cu2+ and forming precipitate, namely, there was synergistic reaction of adsorption and coagulation; the XRD patterns further showed the existence of cation exchange and revealed that the states of Cu2+ in the surface of the composite particles was Cu-Si-O mineral phase and CuO(Cu(OH)2) polymerization precipitation. The bentonite-steel slag composite particles which can play a role of adsorption-coagulation synergism are excellent multifunctional green environmental mineral materials to treat acid mine drainage containing heavy metal ions.Introduction It is reported (Zuo and He 2013) that with the rapid development of industry, the world demand for mineral resources is increasing, while the problem of mine environmental pollution is becoming more and more serious due to the large amount of mining. The pollution of mine wastewater has become a global problem, in which acid mine drainage (AMD) is one of the most serious waste water. It is also reported (Cong and Zhao 2003) that acid mine drainage containing high concentrations of heavy metals and having low pH value, causing serious negative influence to the mining production and ecological environment. Acid mine drainage is one of the most serious environmental pollution to the mining industry. In recent years, it has been widely concerned by scholars at home and abroad."

Jan 1, 2017

By N. Duru

"Gravity concentration is still a challenging area in the mineral industry. This is mainly because of the fine size valuable mineral losses to the tailings during its application. But the recent developments in centrifugal separation methods and their mutual application with conventional separation techniques has increased mineral recoveries. In this paper, field application of conventional gravity separation methods with the combination of 2” diameter hydrocyclone cluster unit and a multi gravity separator (MGS) was discussed. Additionally, particle size distribution and chromite content of the plant streams is presented and initial laboratory test results were compared with the actual plant data throughout the paper. As expected, field data showed derivations from the laboratory tests but the combination of MGS and conventional gravity separation techniques resulted in gravity separation of -0.1 mm chromite particles. INTRODUCTION The purpose of this mineral processing plant project was to investigate the possibility of upgrading chromite ore from 12% to 48% Cr2O3 and having final tailings assay as 2% Cr2O3. For this reason, initially a set of laboratory gravity separation studies were conducted to evaluate the performance of combination of 2” diameter hydrocyclone cluster and multigravity separator. After obtaining successful results from the laboratory work, a feasibility study was initiated. Economical results of the feasibility study showed that an achievable high net present and return on investment values. Following the investment decision; engineering, equipment procurement, construction of the processing plant was completed in eighteen months. This paper focuses on the initial laboratory test work results, operational data of the 2” diameter hydrocyclones and MGS units; resulted chromite recoveries. Processed ore has the chromite associated with serpentine and olivine minerals. The chromite particles are generally in round shapes with sizes between 50 µm to 1600 µm and average size of 450 µm. The microscope images of the chromite and associated formations are presented on Figure 1.Chromite is formed in mixture with iron oxides, with varying amounts of magnesium, aluminum. The average chemical composition of the representative drill core samples of the ore deposit is given on Table 1."

Jan 1, 2017